queued internally. This works around issue in the isci HAL where it cannot
accept new I/O to a device after a resetting->ready state transition until
the completion context has unwound.
This issue was found by submitting non-tagged CCBs through pass(4) interface
to a SATA disk with an extremely small timeout value (5ms). This would trigger
internal resets with I/O in the isci(4) internal queues.
The small timeout value had not been intentional (and original reporter has
since changed his test to use 5sec instead), but it did uncover this corner
case that would result in a hung disk.
Sponsored by: Intel
Reported and tested by: Ravi Pokala <rpokala at panasas dot com>
Reviewed by: scottl (earlier version)
MFC after: 1 week
disabled or the system is in shutdown procedure.
This should fix the problem which kernel never response to the sleep
button press events after the message `suspend request ignored (not
ready yet)'.
MFC after: 3 days
There's some TX path TDMA code in if_ath_tx.c which should be migrated
out, but first I should likely try and verify/fix/repair the TDMA support
in 9.x and -HEAD.
* migrate the rx processing out into if_ath_rx.c
* migrate the TSF functions into if_ath_tsf.h, as inlines
This is in prepration for supporting the EDMA RX routines, required to
support the AR93xx series NICs.
TODO:
* ath_start() shouldn't be private, but it's called as part of
the RX path. I should likely migrate ath_rx_tasklet() back into
if_ath.c and then return this to be 'static'. The RX code really
shouldn't need to see TX routines (and vice versa.)
* ath_beacon_* should be in if_ath_beacon.[ch].
* ath_tdma_* should be in if_ath_tdma.[ch] ...
Supermicro LCD screen modules seem to not support accessing reports through
the control pipes, but working fine with the interrupt pipes.
Sponsored by: iXsystems, Inc.
MFC after: 1 week
The NAND Flash environment consists of several distinct components:
- NAND framework (drivers harness for NAND controllers and NAND chips)
- NAND simulator (NANDsim)
- NAND file system (NAND FS)
- Companion tools and utilities
- Documentation (manual pages)
This work is still experimental. Please use with caution.
Obtained from: Semihalf
Supported by: FreeBSD Foundation, Juniper Networks
add some more BAR debugging logic.
* Change the definition of ath_debug and ath_softc.sc_debug from
int to uint64_t;
* Change the relevant sysctls;
* Add a new BAR TX debugging field;
* Use this in if_ath_tx.
This has been tested by using the sysctl program, which happily allows
for fields > 32 bits to be configured.
Although I _should_ handle the other errors in various ways (specifically
errors like FILT), treating them as having transmitted successfully
is completely wrong. Here, they'd be counted as successful and the BAW
would be advanced.. but the RX side wouldn't have received them.
The specific errors I've been seeing here are HAL_TXERR_FILT.
This patch does fix the issue - I've tested it using -i 0.001 pings
(enough to start aggregation) and now the behaviour is correct:
* The RX side never sees a "moved window" error, and
* The TX side sends BARs as needed, with the RX side correctly handling
them.
PR: kern/167902
depending upon the bootloader initialising it.
The aim is to eventually support a full switch set and reinitialisation
rather than relying on a consistent bootloader setup.
Remove the port flood config from arswitch.c, it's not yet used and
it's totally incorrect.
Whilst I'm here, also add in a comment describing why the full switch
reset is disabled.
Obtained from: Linux (OpenWRT) - Values
size for the AR7240.
* Include SM/MS macros, thanks to ath_hal(4).
* This field is for normal packets, VLAN and other headers are added to
this by the switch device.
* Set the MTU to 1536, to match what is done in Linux. Use the SM
macro to write this field.
Obtained from: Atheros (AR7240 datasheet), Linux OpenWRT (MTU default)
a taskqueue.
This gives a 16% performance improvement under high load on slow systems,
especially when vr shares an interrupt with another device, which is
common with the Alix x86 boards.
Contrary to the other devices, I left the interrupt processing for loop
in because there was no significant difference in performance and this
should avoid enqueuing more taskqueues unnecessarily.
We also decided to move the vr_start_locked() call inside the for loop
because we found out that it helps performance since TCP ACKs now have a
chance to go out quicker.
Reviewed by: yongari (older version, same idea)
Discussed with: yongari, jhb
to allow drivers to handle request completion directly without passing
them to the CAM SWI thread removing extra context switch.
Modify all ATA/SATA drivers to use them.
Reviewed by: gibbs, ken
MFC after: 2 weeks
* Add in the AR724x support. It probes the same as an AR8216/AR8316, so
just add in a hint to force the probe success rather than auto-detecting
it.
* Add in the missing entries from conf/files, lacking in the previous
commit.
The register values and CPU port / mirror port initialisation value was
obtained from Linux OpenWRT ag71xx_ar7240.c.
The DELAY(1000) to let things settle is my local workaround. For some
reason, PHY4 doesn't seem to probe very reliably without it. It's quite
possible that we're missing some MDIO bus initialisation code in if_arge
for the AR724x case. As I dislike DELAY() workarounds in general, it's
definitely worth trying to figure out why this is the case.
Tested on: AP93 (AR7240) reference design
Obtained from: Linux OpenWRT
PAE to insta-panic on startup. Remove one unused variable that was
commented out.
Reviewed by: ambrisko@
Obtained from: jhb@ peter@ bz@ and countless others during BSDCAN
MFC after: 3 days
This is designed to support the very basic ethernet switch chip behaviour,
specifically:
* accessing switch register space;
* accessing per-PHY registers (for switches that actually expose PHYs);
* basic vlan group support, which applies for the rtl8366 driver but not
for the atheros switches.
This also includes initial support for:
* rtl8366rb support - which is a 10/100/1000 switch which supports
vlan groups;
* Initial Atheros AR8316 switch support - which is a 10/100/1000 switch
which supports an alternate vlan configuration (so the vlan group
methods are stubbed.)
The general idea here is that the switch driver may speak to a variety of
backend busses (mdio, i2c, spi, whatever) and expose:
* If applicable, one or more MDIO busses which ethernet interfaces can
then attach PHYs to via miiproxy/mdioproxy;
* exposes miibusses, one for each port at the moment, so ..
* .. a PHY can be exposed on each miibus, for each switch port, with all
of the existing MII/ifnet framework.
However:
* The ifnet is manually created for now, and it isn't linked into the
interface list, nor can you (currently) send/receive frames on this ifnet.
At some point in the future there may be _some_ support for this, for
switches with a multi-port, isolated mode.
* I'm still in the process of sorting out correct(er) locking.
TODO:
* ray's switch code in zrouter (zrouter.org) includes a much more developed
newbus API that covers the various switch methods, as well as a
capability API so drivers, the switch layer and the userland utility
can properly control the subset of supported features.
The plan is to sort that out later, once the rest of ray's switch drivers
are brought over and extended to export MII busses and PHYs.
Submitted by: Stefan Bethke <stb@lassitu.de>
Reviewed by: ray
deterministically handled after the corresponding PHY drivers when
loaded as modules. Otherwise, when these MAC/PHY driver pairs are
compiled into a single module probing the PHY driver may fail. This
makes r151438 and r226154 actually work. [1]
Reported and tested by: yongari (fxp(4))
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
Submitted by: jhb [1]
MFC after: 3 days
as possible when using more than one igb(4) adapter. This
means that queues will not be bound to the same CPUs if
there are more CPUs availble.
This is only applicable to a system that has multiple interfaces.
Obtained from: Yahoo! Inc.
MFC after: 3 days
controller to perform MDIO type accesses to a remote transceiver
using message pages defined through MRBE(multirate backplane
ethernet). It's used in blade systems(e.g Dell Blade m610) which
are connected to pass-through blades rather than traditional
switches.
This change directly manipulates firmware's mailboxes to control
remote PHY such that it does not use mii(4). Alternatively, as
David said, it could be implemented in brgphy(4) by creating a fake
PHY and let brgphy(4) do necessary mii accesses and bce(4) can
implement mailbox accesses based on the type of brgphy(4)'s mii
accesses. Personally, I think it would make brgphy(4) hard to
maintain since it would have to access many bce(4) registers in
brgphy(4). Given that there are users who are suffering from lack
of remote PHY support, it would be better to get working system
rather than waiting for complete/perfect implementation.
Tested by: Jan Winter ( jan.winter <> kantarmedia dot de )
Reviewed by: davidch (initial version)
MFC after: 2 weeks
