longer uses these interrupt vectors for its ISA interrupt pins, so these
entries will not be overwritten. If we get a spurious interrupt from the
ATPIC when using the APIC, it will be treated as a stray interrupt instead
of causing a panic.
- Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff
range. The pmap lazyfix IPI was reordered down next to the TLB
shootdowns to avoid conflicting with the spurious interrupt vector.
- Move the base of APIC interrupts up 16 so that the first 16 APIC
interrupts do not overlap the vectors used by the ATPIC.
- Remove bogus interrupt vector reservations for LINT[01].
- Now that 0xc0 - 0xef are available, use them for device interrupts.
This increases the number of APIC device interrupts to 191.
- Increase the system-wide number of global interrupts to 191 to catch up
to more APIC interrupts.
Requested by: peter (2)
vector stubs and into the C functions they call.
- Move disabling and EOIing of interrupt sources out of PIC driver entry
points and into intr_execute_handlers(). Intr_execute_handlers() only
disables a source for an interrupt if it is a stray interrupt or has
threaded handlers. Sources with fast handlers no longer disable (mask)
the source while executing the handlers.
- Move the setting of clkintr_pending into intr_execute_handlers() and set
the variable for any interrupt source with a vector of 0. (Should only
be true for IRQ 0.) This fixes clkintr_pending in the NO_MIXED_MODE
case.
- Implement lapic_eoi() and use it to implement ioapic_eoi_source().
- Rename atpic_sched_ithd() to atpic_handle_intr() since it is used to
handle all atpic interrupts and not just threaded ones.
Inspired by: peter's changes to amd64 in p4 (1)
Requested by: bde (2)
interrupt such as IRQ 22 or 19. However, the ACPI BIOS still routes
interrupts from some PCI devices to the same intpin calling the pin
IRQ 22. Thus, ACPI expects to address a single interrupt source via two
different names. To work around this, if the SCI is remapped to a non-ISA
interrupt (i.e., greater than 15), then we use
acpi_OverrideInterruptLevel() function to tell ACPI to use IRQ 22 or 19
rather than IRQ 9 for the SCI.
Previously we would change IRQ 22 or 19's name to IRQ 9 when we encountered
such an Interrupt Source Override entry in the MADT which routed the SCI
properly but left PCI devices mapped to IRQ 22 or 19 w/o a routable
interrupt.
Tested by: sos
should now only have HTT CPUs if they have explicitly asked for them
either by enabling HyperThreading in the BIOS or by using the
MPTABLE_FORCE_HTT kernel option.
should only be used if they are enabled in the BIOS. Now that we support
enumerating CPUs using the ACPI MADT, any HTT machine using ACPI should
respect the BIOS setting. For HTT machines with ACPI disabled in the
kernel, the MPTABLE_FORCE_HTT kernel option can be used to try to probe HTT
CPUs like have done in the past for the MP Table case. This option should
only be enabled if HTT is enabled in the BIOS.
Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
pmap_pte() and pmap_pte_quick(). The distinction being based upon the
locks that are held by the caller. When the given pmap is not the
current pmap, pmap_pte() should be used when Giant is held and
pmap_pte_quick() should be used when the vm page queues lock is held.
- When assigning to PMAP1 or PMAP2, include PG_A anf PG_M.
- Reenable the inlining of pmap_is_current().
In collaboration with: tegge
pin that is used by the default identity mapping if it still maps to the
old vector. The ACPI case might need some tweaking for the SCI interrupt
case since ACPI likes to address the intpin using both the IRQ remapped to
it as well as the previous existing PCI IRQ mapped to it.
Reported by: kan
rather than signed. This fixes some cosmetics such as verbose printf's
for IRQs greater than 127.
- The calculation for next_ioapic_base was also adjusted so that it will
only complain once for each hole in the IRQs provided by ACPI for IO
APICs.
Reported by: Michal Mertl <mime@traveller.cz>
isa_device pointer as its argument and uses that to call the driver's
interrupt handler passing the unit number as its argument. This should
fix COMPAT_OLDISA devices with a unit number of 0.
Reviewed by: peter
Reported by: bde
