handling.
- Extended PWRCTL/PMU APIs to support querying clock frequency during very
early boot, prior to bus attach.
- Implement generic PMU-based calculation of UART rclk values.
- Replaced use of static frequency tables (bcm_socinfo) with
runtime-determined values.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7552
- Added bhnd_pmu driver implementations for PMU and PWRCTL chipsets,
derived from Broadcom's ISC-licensed HND code.
- Added bhnd bus-level support for routing per-core clock and resource
power requests to the PMU device.
- Lift ChipCommon support out into the bhnd module, dropping
bhnd_chipc.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7492
This adds support for performing platform_reset() on all supported
devices, using early boot enumeration of chipc capabilities and
available cores.
- Added Broadcom-specific MIPS CP0 register definitions used by
BCM4785-specific reset handling.
- Added a bcm_platform structure for tracking chipc/pmu/cfe platform
data.
- Extended the BCMA EROM API to support early boot lookup of core info
(including port/region mappings).
- Extended platform_reset() to support PMU, PMU+AOB, and non-PMU
devices.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7539
Rather than enabling the I/O MMU when the vmm module is loaded,
defer initialization until the first attempt to pass a PCI device
through to a guest. If the I/O MMU fails to initialize or is not
present, than fail the attempt to pass a PCI device through to a
guest.
The hw.vmm.force_iommu tunable has been removed since the I/O MMU is
no longer enabled during boot. However, the I/O MMU support can be
disabled by setting the hw.vmm.iommu.enable tunable to 0 to prevent
use of the I/O MMU on any systems where it is buggy.
Reviewed by: grehan
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7448
can be in after receiving a FIN.
FWIW, NetBSD has this change for quite some time.
This has been tested at Netflix and Limelight in production traffic.
Reported by: Sam Kumar <samkumar99 at gmail.com> on transport@
Reviewed by: rrs
MFC after: 4 weeks
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D7475
- Return appropriate error code instead of ENOMEM when sosend() fails in
send_mpa_req.
- Fix for problematic race during destroy_qp.
- Abortive close in the failure of send_mpa_reject() instead of normal close.
- Remove the unnecessary doorbell flowcontrol logic.
Submitted by: Krishnamraju Eraparaju at Chelsio
MFC after: 1 month
Sponsored by: Chelsio communications
I-FORWARD-TSN chunk before any DATA or I-DATA chunk.
Thanks to Julian Cordes for finding this problem and prividing
packetdrill scripts to reporduce the issue.
MFC after: 3 days
And use new RNDIS set to configure NDIS offloading parameters.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7641
And switch MAC address query to use new RNDIS query function.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7639
Summary:
First time BSS is cleared in booke_init(), Second time it's cleared in
powerpc_init(). Any variable initialized between two those guys gets wiped out
what is wrong. In particular it wipes tlb1_entries initialized by tlb1_init(),
which was fine when tlb1_init() was called a second time, but this was removed
in r304656.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7638
'show active trace', or 'acttrace' for short, prints backtraces from running
threads only.
Reviewed by: mjg
Differential Revision: https://reviews.freebsd.org/D7646
hardware send and receive PDU limits. Report these limits to ICL and
take them into account when setting the socket's send and receive buffer
sizes. The driver used a single hardcoded limit everywhere prior to
this change.
Sponsored by: Chelsio Communications
obliterate possible error from sleep with errors from
umtxq_check_susp(), when looping to clear URWLOCK_{READ,WRITE}_WAITERS.
Noted and reviewed by: vangyzen
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
If there was some error, e.g. the sleep was interrupted, as in the
referenced PR, do_rw_rdlock() did not cleared URWLOCK_READ_WAITERS.
Since unlock only wakes up write waiters when there is no read
waiters, for URWLOCK_PREFER_READER kind of locks, the result was
missed wakeups for writers.
In particular, the most visible victims are ld-elf.so locks in
processes which loaded libthr, because rtld locks are urwlocks in
prefer-reader mode. Normal rwlocks fall into prefer-reader mode only
if thread already owns rw lock in read mode, which is not typical and
correspondingly less visible. In the PR, unowned rtld bind lock was
waited for in the process where only one thread was left alive.
Note that do_rw_wrlock() correctly clears URWLOCK_WRITE_WAITERS in
case of errors.
Reported and tested by: longwitz@incore.de
PR: 211947
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
the l2 entry is a block type and not an l3 page.
While here fix the string to correct the level name and add a missing ')'.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
syscons spinlock for the output routine alone. It is better to extend
the coverage of the first syscons spinlock added in r162285. 2 locks
might work with complicated juggling, but no juggling was done. What
the 2 locks actually did was to cover some of the missing locking in
each other and deadlock less often against each other than a single
lock with larger coverage would against itself. Races are preferable
to deadlocks here, but 2 locks are still worse since they are harder
to understand and fix.
Prefer deadlocks to races and merge the second lock into the first one.
Extend the scope of the spinlocking to all of sc_cnputc() instead of
just the sc_puts() part. This further prefers deadlocks to races.
Extend the kdb_active hack from sc_puts() internals for the second lock
to all spinlocking. This reduces deadlocks much more than the other
changes increases them. The s/p,10* test in ddb gets much further now.
Hide this detail in the SC_VIDEO_LOCK() macro. Add namespace pollution
in 1 nested #include and reduce namespace pollution in other nested
#includes to pay for this.
Move the first lock higher in the witness order. The second lock was
unnaturally low and the first lock was unnaturally high. The second
lock had to be above "sleepq chain" and/or "callout" to avoid spurious
LORs for visual bells in sc_puts(). Other console driver locks are
already even higher (but not adjacent like they should be) except when
they are missing from the table. Audio bells also benefit from the
syscons lock being high so that audio mutexes have chance of being
lower. Otherwise, console drviver locks should be as low as possible.
Non-spurious LORs now occur if the bell code calls printf() or is
interrupted (perhaps by an NMI) and the interrupt handler calls
printf(). Previous commits turned off many bells in console i/o but
missed ones done by the teken layer.
tso_segsz pkthdr field during RX processing, and use the information in TCP for
more correct accounting and as a congestion control input. This is only a start,
and an audit of other uses for the data is left as future work.
Reviewed by: gallatin, rrs
Sponsored by: Netflix, Inc.
Differential Revision: https://reviews.freebsd.org/D7564
set later in the function. This fixes a potential NULL pointer dereference
found on arm64.
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
to what the 32-bit arm code does, with the exception that it always assumes
the tag is non-coherent.
Tested by: jmcneill
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
- Increasing queue depth gives ~100% performance improvement for
randwrite fio test in Azure.
- New channel selection, which takes LUN id and the current cpuid
into consideration, gives additional ~20% performance improvement
for ranwrite fio test in Azure.
Submitted by: Hongzhang Jiang <honzhan microsoft com>
Modified by: sephe
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7622
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
indicate (potentially partial) success of the open. Use these to
decide what to close in sccnclose(). Only grab/ungrab use open/close
so far.
Add a per-sc variable to count successful keyboard opens and use
this instead of the grab count to decide if the keyboad state has
been switched.
Start fixing the locking by using atomic ops for the most important
counter -- the grab level one. Other racy counting will eventually
be fixed by normal mutex or kdb locking in most cases.
Use a 2-entry per-sc stack of states for grabbing. 2 is just enough
to debug grabbing, e.g., for gets(). gets() grabs once and might not
be able to do a full (or any) state switch. ddb grabs again and has
a better chance of doing a full state switch and needs a place to
stack the previous state. For more than 3 levels, grabbing just
changes the count. Console drivers should try to switch on every i/o
in case lower levels of nesting failed to switch but the current level
succeeds, but then the switch (back) must be completed on every i/o
and this flaps the state unless the switch is null. The main point
of grabbing is to make it null quite often. Syscons grabbing also
does a carefully chosen screen focus that is not done on every i/o.
Add a large comment about grabbing.
Restore some small lost comments.
- in sccnopen(), open the keyboard before the screen. The keyboard
currently requires Giant (although it must be spinlocked to work
correctly as a console), so the previous order would be a LOR if
it has any semblance of locking.
- add a (currently dummy) state arg to scgetc().
As the support for large blocks was enabled in loader zfs code, the
heap in userboot was left not changed, resulting with failure of detecting
and accessing zfs pools for bhyve virtual machines.
This fix does set the heap to use same amount of memory as the zfsloader
is using. To make it possible to test and verify loader functions, bhyve
is providing very useful option, but it also means, we like to keep feature
parity with [zfs]loader as close as possible.
PR: 212038
Reported by: dfh0522@gmail.com
Reviewed by: allanjude, grehan
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D7635
The issue was introduced with adding support for salted checksums, and
was revealed by bhyve userboot.so.
During pool discovery the loader is reading pool label from disks, and
at that time the spa structure is not yet set up, so the NULL pointer
is passed for spa. This condition must be checked to avoid the corruption
of the memory and NULL pointer dereference.
PR: 212114
Reported by: tsoome@freebsd.com
Reviewed by: allanjude
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D7634