* break out the operating mode and rx filter into new functions, rather
than them being hard-coded
* if we're in sniffer mode or not associated, set the BSS MAC to all zero,
rather than relying on a chip reset to do it for us
* add comments about .. how interestingly buggy the chip is.
Tested:
* AR9170 + AR9102, STA+monitor mode
Obtained from: linux carl9170 (general chip workings, constant definitions)
Switch to add_channel / add_channel_ht40 + pass channel's TX power
for the last.
Tested by: dhw
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6141
driver is (or behaves identically to) /dev/mem. Remove the D_MEM flag
from random drivers.
Note that currently the D_MEM flag does not affect any behaviour, but
this going to change in the next commit.
Noted and reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-Differential revision: https://reviews.freebsd.org/D6149
The Linux driver sets the rate_n_flags regardless of whether it's being
sent using firmware rate control or local rate control. This includes
the antenna configuration.
Thanks to Kyle Evans <kevans91@ksu.edu> for pointing this out to me
and doing some investigation/testing on his end.
Tested:
* Intel 7260 STA, 2G and 5G networks
I .. can't believe I missed this.
This showed up because the AP was TX'ing LDPC to an iwm(4) chipset,
which didn't advertise LDPC and doesn't /accept/ LDPC. Amusingly, all
the two other FreeBSD 11n parts I had tested with (AR9380, Intel 7260)
and I completely forgot to test on ye olde hardware.
That'll teach me.
Tested:
* AR9580 (AP) - Intel 7260 (STA), AR9380 (STA), Intel 6205 (STA)
function to error out early when no port module is present and doing
eeprom access. This also prevents error codes from filling up in
dmesg.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
LDPC adds better transmit reliability if both ends support it.
You in theory can do both STBC and LDPC at the same time.
If I see issues I'll disable it.
* Only enable it if both ends of a connection negotiate it.
* Disable it if any rate is non-11n.
* Count both LDPC TX and STBC TX.
Tested:
* AR9380, STA mode
Arguably we should only be doing the probe/attach to children of
these devices as well.
Tested by: Michal Stanek <mst_semihalf.com> (arm64)
Differential Revision: https://reviews.freebsd.org/D6133
Add new function gpio_alloc_intr_resource(), which allows an allocation
of interrupt resource associated to given gpio pin. It also allows to
specify interrupt configuration.
Note: This functionality is dependent on INTRNG, and must be
implemented in each GPIO controller.
Labels are limitted by 32 on EF10. It is not sufficient on powerful hosts.
Since only one RxQ is running over each EvQ, zero label may be used.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
PR: 208267
Differential Revision: https://reviews.freebsd.org/D6121
This allows the PCI-PCI bridge driver to save a reference to the child
device in its softc.
Note that this required moving the "pci" device creation out of
acpi_pcib_attach(). Instead, acpi_pcib_attach() is renamed to
acpi_pcib_fetch_prt() as it's sole action now is to fetch the PCI
interrupt routing table.
Differential Revision: https://reviews.freebsd.org/D6021
Rescanning a PCI bus uses the following steps:
- Fetch the current set of child devices and save it in the 'devlist'
array.
- Allocate a parallel array 'unchanged' initalized with NULL pointers.
- Scan the bus checking each slot (and each function on slots with a
multifunction device).
- If a valid function is found, look for a matching device in the 'devlist'
array. If a device is found, save the pointer in the 'unchanged' array.
If a device is not found, add a new device.
- After the scan has finished, walk the 'devlist' array deleting any
devices that do not have a matching pointer in the 'unchanged' array.
- Finally, fetch an updated set of child devices and explicitly attach any
devices that are not present in the 'unchanged' array.
This builds on the previous changes to move subclass data management into
pci_alloc_devinfo(), pci_child_added(), and bus_child_deleted().
Subclasses of the PCI bus use custom rescan logic explicitly override the
rescan method to disable rescans.
Differential Revision: https://reviews.freebsd.org/D6018
This greatly reduces the oqdrops under heavy workload.
For TCP send/recv test (10K concurrent connections):
oqdrops is reduced by 17% on sending side, and 57% on receiving side.
For nginx-1.8/wrk-4 1KB object test (10K concurrent connections,
4 requests/connection):
oqdrops is reduced by 44% on nginx side, and 10% on wrk side.
MFC after: 1 week
Sponsored by: Microsoft OSTC
- Factor out common part to zynq-7000.dtsi
- Fix problem with Zynq interrupts by using interrupt "triples"
in .dtsi file to differentiate between edge-triggered and
level-triggered interrupts
- cgem driver now recognizes "status" property
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D6095
The softc member 'ciss_logical' is an array of 'ciss_max_logical_bus' members.
Most of the time it is iterated correctly. This patch fixes the two instances
where the driver iterated off the end of the array.
Reported by: Coverity
CID: 1305492
Sponsored by: EMC / Isilon Storage Division
ism_stop() already destroys and frees 'sp', including a call to ic_destroy().
Don't dereference 'sp' after ism_stop() and don't invoke ic_destroy() on the
freed memory either.
Reported by: Coverity
CIDs: 1006109, 1304861
Sponsored by: EMC / Isilon Storage Division
This is a trivial follow-up to r296308. Annotate the intentional fallthrough
to make it clear for future readers and linters.
Reported by: Coverity
CID: 1352716
Discussed with: jhb
Sponsored by: EMC / Isilon Storage Division
Introduced in r298594. There is no path before the 'vap == NULL' check where
vap is not already dereferenced.
Reported by: Coverity
CID: 1354979
Sponsored by: EMC / Isilon Storage Division
