within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
o AR8151 v1.0(L1D) gigabit ethernet controller
o AR8151 v2.0(L1D) gigabit ethernet controller
o AR8152 v1.1(L2CB) fast ethernet controller
o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.
HW donated by: Atheros Communications, Inc.
- Increase target limit from 4 to 64; this limit will be removed entirely
at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.
Submitted by: Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by: Dansk Scanning A/S, Data Robotics Inc.
This fixes booting from a ZFS mirror with a unavailable primary device.
PR: kern/148655
Reviewed by: avg
Approved by: delphij (mentor)
MFC after: 3 days
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.
hint.ste.0.prefer_iomap="1"
PR: kern/149285
MFC after: 5 days
number of CPUs detection.
However, that was not mention at all, the problem was not reported, the
patch has not been MFCed and the fix is mostly improper.
Fix the original overflow (caused when 32 CPUs must be detected) by
just using a different mathematical computation (it also makes more
explicit the size of operands involved, which is good in the moment
waiting for a more complete support for a large number of CPUs).
PR: kern/148698
Submitted by: Joe Landers <jlanders at vmware dot com>
Tested by: gianni
MFC after: 10 days
td_critnest > 1 when not already running on the desired CPU read the
TICK counter of the BSP via a direct cross trap request in that case
instead.
- Treat the STICK based timecounter the same way as the TICK based one
regarding its quality and obtaining the counter value from the BSP.
Like the TICK timers the STICK ones also are only synchronized during
their startup (which might not result in good synchronicity in the
first place) but not afterwards and might drift over time, causing
problems when the time is read from different CPUs (see r135972).
interface goes to issue LINK_UP, then LINK_DOWN, then LINK_UP at
cold boot. This behavior is not observed when carp(4) interface
is created slightly later, when the underlying interface is fully
up.
Before this change what happen at boot is roughly:
- ifconfig creates em0 interface;
- ifconfig clones a carp device using em0;
(em0's link state is DOWN at this point)
- carp state: INIT -> BACKUP [*]
- carp state: BACKUP -> MASTER
- [Some negotiate between em0 and switch]
- em0 kicks up link state change event
(em0's link state is now up DOWN at this point)
- do_link_state_change() -> carp_carpdev_state()
- carp state: MASTER -> INIT (via carp_set_state(sc, INIT)) [+]
- carp state: INIT -> BACKUP
- carp state: BACKUP -> MASTER
At the [*] stage, em0 did not received any broadcast message from other
node, and assume our node is the master, thus carp(4) sets the link
state to "UP" after becoming a master. At [+], the master status
is forcely set to "INIT", then an election is casted, after which our
node would actually become a master.
We believe that at the [*] stage, the master status should remain as
"INIT" since the underlying parent interface's link state is not up.
Obtained from: iXsystems, Inc.
Reported by: jpaetzel
MFC after: 2 months
uname and gname weren't overwritten, so the
disk restore would use those to lookup the
original uid/gid again. Clearing the uname
and gname prevents this.
Reported by: swell.k
MFC after: 7 days
suspend state. Also disable master clock after PHY power down,
this is supposed to save more power. The master clock should be
enabled if WOL is active.
to single CPUs more efficiently with Cheetah(-class) and Jalapeno CPUs.
Besides being used to implement the ipi_cpu() introduced in r210939,
cpu_ipi_single() will also be used internally by the sparc64 MD code.
- Factor out the Jalapeno support from the Cheetah IPI send functions
in order to be able to more easily and efficiently implement support
for more than 32 target CPUs as well as a workaround for Cheetah+
erratum 25 for the latter.
the vfs.read_max default. For most systems this means going from 128 KiB
to 256 KiB, which is still very conservative and lower than what most
other operating systems use, but as a sane default should not
interfere much with existing systems.
For systems with RAID volumes and/or virtualization envirnments, where
read performance is very important, increasing this sysctl tunable to 32
or even more will demonstratively yield additional performance benefits.
If MAXPHYS ever gets bumped up, it will probably be a good idea to slave
read_max to it.
SOCK_DGRAM socket. MSG_TRUNC was only returned when some mbufs could
not be copied to the application. If some data was left in the last
mbuf, it was correctly discarded, but MSG_TRUNC was not set.
Reviewed by: bz
MFC after: 3 weeks
