Commit Graph

3 Commits

Author SHA1 Message Date
Warner Losh
098ca2bda9 Start each of the license/copyright comments with /*-, minor shuffle of lines 2005-01-06 01:43:34 +00:00
Marcel Moolenaar
06287620b4 Add locking to the hardware drivers. I intended to figure out more
precisely where locking would be needed before adding it, but it
seems uart(4) draws slightly too much attention to have it without
locking for too long.
The lock added is a spinlock that protects access to the underlying
hardware. As a first and obvious stab at this, each method of the
hardware interface grabs the lock. Roughly speaking this serializes
the methods. Exceptions are the probe, attach and detach methods.
2003-09-17 01:41:21 +00:00
Marcel Moolenaar
27d5dc189c The uart(4) driver is an universal driver for various UART hardware.
It improves on sio(4) in the following areas:
o  Fully newbusified to allow for memory mapped I/O. This is a must
   for ia64 and sparc64,
o  Machine dependent code to take full advantage of machine and firm-
   ware specific ways to define serial consoles and/or debug ports.
o  Hardware abstraction layer to allow the driver to be used with
   various UARTs, such as the well-known ns8250 family of UARTs, the
   Siemens sab82532 or the Zilog Z8530. This is especially important
   for pc98 and sparc64 where it's common to have different UARTs,
o  The notion of system devices to unkludge low-level consoles and
   remote gdb ports and provides the mechanics necessary to support
   the keyboard on sparc64 (which is UART based).
o  The notion of a kernel interface so that a UART can be tied to
   something other than the well-known TTY interface. This is needed
   on sparc64 to present the user with a device and ioctl handling
   suitable for a keyboard, but also allows us to cleanly hide an
   UART when used as a debug port.

Following is a list of features and bugs/flaws specific to the ns8250
family of UARTs as compared to their support in sio(4):
o  The uart(4) driver determines the FIFO size and automaticly takes
   advantages of larger FIFOs and/or additional features. Note that
   since I don't have sufficient access to 16[679]5x UARTs, hardware
   flow control has not been enabled. This is almost trivial to do,
   provided one can test. The downside of this is that broken UARTs
   are more likely to not work correctly with uart(4). The need for
   tunables or knobs may be large enough to warrant their creation.
o  The uart(4) driver does not share the same bumpy history as sio(4)
   and will therefore not provide the necessary hooks, tweaks, quirks
   or work-arounds to deal with once common hardware. To that extend,
   uart(4) supports a subset of the UARTs that sio(4) supports. The
   question before us is whether the subset is sufficient for current
   hardware.
o  There is no support for multiport UARTs in uart(4). The decision
   behind this is that uart(4) deals with one EIA RS232-C interface.
   Packaging of multiple interfaces in a single chip or on a single
   expansion board is beyond the scope of uart(4) and is now mostly
   left for puc(4) to deal with. Lack of hardware made it impossible
   to actually implement such a dependency other than is present for
   the dual channel SAB82532 and Z8350 SCCs.

The current list of missing features is:
o  No configuration capabilities. A set of tunables and sysctls is
   being worked out. There are likely not going to be any or much
   compile-time knobs. Such configuration does not fit well with
   current hardware.
o  No support for the PPS API. This is partly dependent on the
   ability to configure uart(4) and partly dependent on having
   sufficient information to implement it properly.

As usual, the manpage is present but lacks the attention the
software has gotten.
2003-09-06 23:13:47 +00:00