switches. Not as lazy as it could be. Changing FPU state with sigcontext
still TODO.
fpu.c - convert some asm to inline C, and macroize fpu loads/stores
swtch.S - call out to save/restore fpu routines
trap.c - always call enable_fpu, since this shouldn't be called once
the FPU has been enabled for a thread
genassym.c - define for pcb fpu flag
and save/restore during a context switch.
The USER_SR could be overwritten when the current thread was switched
out with a faulting copyin/copyout.
Approved by: Benno
choosethread() in MI C code instead of doing it in in assembly in all the
various cpu_switch() functions. This fixes problems on ia64 and sparc64.
Reviewed by: julian, peter, benno
Tested on: i386, alpha, sparc64
The case in cpu_switch() where there isn't a higher priority thread
(choosethread() == curthread) uses r4 as the PCB context pointer. However, the
use of r4 after the label L2 is incorrect, since it was probably trashed by
the call to choosethread, and in any case was set up to curthread at the start
of the routine.
This condition will occur when an interrupt thread schedules a netisr, which
is a lower priority thread.
Another (probably unnecessary) difference is that I was paranoid about
register trashing, so I decided to save r2 and r13 as well.
Submitted by: Peter Grehan <peterg@ptree32.com.au>
Highlights include:
- New low-level trap code from NetBSD. The high level code still needs a lot
of work.
- Fixes for some pmap handling in thread switching.
- The kernel will now get to attempting to jump into init in user mode. There
are some pmap/trap issues which prevent it from actually getting there though.
Obtained from: NetBSD (parts)
boot sequence.
The new pmap.c is based on NetBSD's newer pmap.c (for the mpc6xx processors)
which is 70% faster than the older code that the original pmap.c was based
on. It has also been based on the framework established by jake's initial
sparc64 pmap.c.
There is no change to how far the kernel gets (it makes it to the mountroot
prompt in psim) but the new pmap code is a lot cleaner.
Obtained from: NetBSD (pmap code)
- The MI portions of struct globaldata have been consolidated into a MI
struct pcpu. The MD per-CPU data are specified via a macro defined in
machine/pcpu.h. A macro was chosen over a struct mdpcpu so that the
interface would be cleaner (PCPU_GET(my_md_field) vs.
PCPU_GET(md.md_my_md_field)).
- All references to globaldata are changed to pcpu instead. In a UP kernel,
this data was stored as global variables which is where the original name
came from. In an SMP world this data is per-CPU and ideally private to each
CPU outside of the context of debuggers. This also included combining
machine/globaldata.h and machine/globals.h into machine/pcpu.h.
- The pointer to the thread using the FPU on i386 was renamed from
npxthread to fpcurthread to be identical with other architectures.
- Make the show pcpu ddb command MI with a MD callout to display MD
fields.
- The globaldata_register() function was renamed to pcpu_init() and now
init's MI fields of a struct pcpu in addition to registering it with
the internal array and list.
- A pcpu_destroy() function was added to remove a struct pcpu from the
internal array and list.
Tested on: alpha, i386
Reviewed by: peter, jake
to working but still needs some work to properly switch the full context
(such as saving the fpu registers, switch stacks, etc.). Also, remove some
dead code that was mixed in.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
