my Elektor card. Note that the hints are necessary to specify the
IO base of the pcf chip. This enables to check the IO base when the
probe routine is called during ISA enumeration.
The interrupt driven code is mixed with polled mode, which is wrong
and produces supposed spurious interrupts at each access. I still have
to work on it.
This is part 2/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
It appears to also fix the occasional problems to establish a link on
hme(4) using LU6612 PHYs and shouldn't hurt on those using QS6612 PHYs.
Obtained from: NetBSD
properly. This causes the autonegotiation to e.g. never establish a
100baseTX full-duplex link. The solution to this problem is to manually
write the capabilities from the BMSR to the ANAR every time a media
change occurs, even when already in autonegotiation mode.
The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the
NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which
will set the ANAR according to the BMSR) even when the PHY alread is in
autonegotiation mode. However, while doing the same on FreeBSD (which
involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use
mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia()
causes this driver to no longer work properly in the other modes.
Another drawback of that approach is that this will also force writing
the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which
are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is
known to be used together with 3 different PHYs while only the DP83840A
require this workaround).
So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in
nsphy_service() unconditionally when hanging off of a hme(4) and serving
a media change
This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
pipes, since open pipes are linked off a usbd_interface structure
that is free()'d when the configuration index is changed. Attempting
to close or use such pipes later would access freed memory and
usually crash the system.
The only driver that is known to trigger this problem is if_axe,
which is itself at fault, but it is worth detecting the situation
to avoid the obscure crashes that result from this type of easily
made driver mistakes.
make the key name matching case-insensitive. There are some drivers
and .inf files that have mismatched cases, e.g. the driver will look
for "AdhocBand" whereas the .inf file specifies a registry key to be
created called "AdHocBand." The mismatch is probably a typo that went
undetected (so much for QA), but since Windows seems to be case-insensitive,
we should be too.
In if_ndis.c, initialize rates and channels correctly so that specify
frequences correctly when trying to set channels in the 5Ghz band, and
so that 802.11b rates show up for some a/b/g cards (which otherwise
appear to have no 802.11b modes).
Also, when setting OID_802_11_CONFIGURATION in ndis_80211_setstate(),
provide default values for the beacon interval, ATIM window and dwelltime.
The Atheros "Aries" driver will crash if you try to select ad-hoc mode
and leave the beacon interval set to 0: it blindly uses this value and
does a division by 0 in the interrupt handler, causing an integer
divide trap.
correct. Instead, check it against the possible settings (_PRS) when
the link is probed. This is important when using APIC mode but link
devices still have PIC mode settings. This is also what Linux does.
Additional prodding by: Len Brown len dot brown at intel dot com
based on the destination sleep state. Add a method to restore the old
state on resume. This is needed for the case of suspending to a very low
state disabling a GPE (i.e. S4), resuming, and then suspending to a higher
state (i.e. S3). This case should now keep the proper GPEs enabled.
device can wake the system. For example:
dev.root0.nexus0.acpi0.acpi_lid0.wake: 1
dev.root0.nexus0.acpi0.acpi_button0.wake: 1
dev.root0.nexus0.acpi0.pcib0.wake: 0
dev.root0.nexus0.acpi0.sio0.wake: 0
been developed for use with FreeBSD, version 4.8 and later.
Submitted by: Hema Joyce
Reviewed by: Prafulla Deuskar
Approved by: Prafulla Deuskar
MFC after: 1 week
acpi_wake_init:
Evaluate _PRW and set the GPE type
acpi_wake_set_enable:
Enable or disable a device's GPE.
acpi_wake_sleep_prep:
Perform any last-minute changes to the device to prepare it for
entering the given sleep state.
Also, walk the entire namespace when transitioning to a sleep state,
disabling any GPEs which aren't appropriate for the given state. Transition
acpi_lid and acpi_button to the new API.
This clears the way for non-ACPI-aware devices to wake the system (i.e.
modems) and fixes a problem where systems power up after shutdown when a
GPE is triggered.
In particular, disabling it was likely to break configurations
involving ng_vlan(4) since the latter couldn't control
the parent's VLAN_MTU in the way vlan(4) did.
Pointed out by: ru
does not reliably prevent the triggering of interrupts for all supported
configurations. Thus, the FIFO size probe could cause an interrupt,
which could lead to an interrupt storm in the shared interrupt case.
To prevent this, change ns8250_bus_probe() to use the overflow bit in
the line status register instead of the RX ready bit in the interrupt
identification register to detect whether the FIFO has filled up.
This allows us to clear all bits in the interrupt enable register during
the probe, which should prevent interrupts reliably.
Additionally, the detected FIFO size may be a bit more accurate, because
the overflow bit is only set when the FIFO did actually fill up, while
interrupts would trigger a bit early.
Reviewed and tested on a lot of hardware by: marcel
