r199563:
Fix copy & paste error and remove extra space before colon.
r199608:
Remove unnecessary structure packing.
r199609:
Add initial endianness support. It seems the controller supports
both big-endian and little-endian format in descriptors for Rx path
but I couldn't find equivalent feature in Tx path. So just stick to
little-endian for now.
r199610:
Because we know received bytes including CRC there is no reason to
call m_adj(9). The controller also seems to have a capability to
strip CRC bytes but I failed to activate this feature except for
loopback traffic.
r199611:
Add IPv4/TCP/UDP Tx checksum offloading support. It seems the
controller also has support for IP/TCP checksum offloading for Rx
path. But I failed to find to way to enable Rx MAC to compute the
checksum of received frames.
r199612:
Add __FBSDID.
r199613:
Only Tx checksum offloading is supported now. Remove experimental
code sneaked in r199611.
r199558:
Use bus_{read,write}_4 rather than bus_space_{read,write}_4.
r199561:
Use capability pointer to access PCIe registers rather than
directly access them at fixed address. Frequently the register
offset could be changed if additional PCI capabilities are added to
controller.
One odd thing is ET_PCIR_L0S_L1_LATENCY register. I think it's PCIe
link capabilities register but the location of the register does
not match with PCIe capability pointer + offset. I'm not sure it's
shadow register of PCIe link capabilities register.
Remove complex macros that were used to compute bits values.
Although these macros may have its own strength, its complex
definition make hard to read the code.
Approved by: delphij
o Properly support M5229 revision 0xc7 and 0xc8:
- These revisions no longer have cable detection capability.
- The UDMA support bit of register 0x4b has been dropped without an
replacement.
- According to Linux it's crucial for working ATAPI DMA support to
also set the reserved bit 1 of regsiter 0x53 with these revisions.
o Only set ATA_CHECKS_CABLE for chip versions that actually support
cable detection, i.e. neither for ALI_OLD nor for ALI_NEW revisions
>= 0xc7.
Specify the capability and media bits of the capabilities page in
native, i.e. big-endian, format and convert as appropriate like we
also do with the multibyte fields of the other pages. This fixes
the output of acd_describe() to match reality on big-endian machines
without breaking it on little-endian ones. While at it, also convert
the remaining multibyte fields of the pages read although they are
currently unused for consistency and in order to prevent possible
similar bugs in the future.
Note that r200091 completely overrides r200053 and the merge of the
former is recorded for bookkeeping only.
r200091 won't be merged to 'more stable' branche(s) because of the POLA.
ndis_scan_results() can sleep if the scan results are not ready when
ndis_scan() is called. However, ndis_scan() is invoked from softclock()
and cannot sleep. Move ndis_scan_results() to the ndis driver's scan_end
hook instead.
Unbreak the ata_atapi() usage. Since r200171 (MFC'ed in r200432) the
mode setting functions get a ata_device type device passed instead of
a ata_channel one, thus ata_atapi() has to be adjusted accordingly.
Reviewed by: mav
Large I/Os on Promise controllers reported to cause UDMA ICRC errors and
subsequent timeouts. Restore previous limit for now, at least until
I will have hardware to experiment.
PR: kern/141438
- On entrance to the rx_eof sync RX rings maps with POSTWRITE flag
instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Add support for new BGE chips (5761, 5784 and 57780). These chips uses new
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
Some general cleanup of scatter/gather memory allocation
- We don't need to check malloc return values with M_WAITOK
- remove variables that we don't really need
- cleanup the error paths by just calling drm_sg_cleanup()
- fix drm_sg_cleanup() to be safe to call at any time
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this option deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.(ata|atapi)_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
Limit maximum I/O size, depending on command set supported by device.
It is required to suppot non-LBA48 devices with MAXPHYS above 128K.
Same is done in ada(4).
Add counters for the i7 architecture which were accidentally left
out of the original commit of i7 support. These are all the counters
on pages A-32 and A-33 of the _Intel(R) 64 and IA32 Architectures
Software Developer's Manual Vol 3B_, June 2009. Almost all
of these counters relate to operations on the L2 cache.
Improve support for High-speed USB audio devices.
- fix issues regarding the mixer, where the interface number was not set in
time.
- fix wrong use of resolution parameter.
Submitted by: Hans Petter Selasky
Remove overuse of exclamation marks in kernel printfs, there mere fact a
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
Disable interrupts after doing early takeover of the usb controller in case usb
isnt actually compiled in (or kldloaded) as the controller could cause spurious
interrupts.
Improve High Speed slot allocation mechanism by moving the computation to the
endpoint rather than per xfer and provide functions around get/free of resources.
Submitted by: Hans Petter Selasky
ehci_init() will do reset and set the usbrev flag. Fix problem where
ehci_reset() was called before ehci_init().
PR: usb/140242
Submitted by: Sebastian Huber
- Add usb_fill_bulk_urb() and usb_bulk_msg() linux compat functions [1]
- Don't write actual length if the actual length pointer is NULL [2]
- correct Linux Compatibility error codes for short isochronous IN transfers
and make status field signed.
Submitted by: Leunam Elebek [1], Manuel Gebele [2]
updates device entries supported with the product name not magic numbers
and sorts entries. WUSB54GCV2 is added.
overhauls urtw(4) for supporting RTL8187B devices properly that there
was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code.
Reduce probe priority of USB input devices to BUS_PROBE_GENERIC from
BUS_PROBE_SPECIFIC. This allows device-specific drivers like atp to
attach reliably.
