EtherJet, the interrupt is selected in the eeprom based on the layout
of the PC Card board. Since this is encoded into the EEPROM, and has
no relationship to the IRQ that the pccard bridge routes the PC Card's
interrupt pin to.
As such, stop writing to that register. This gets my EtherJet working.
# The eeprom reading code appears to be totally wrong for my EtherJet
# card. This causes the card to bogusly detect the media options
# available.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
o Fix minor type problems
o Fix minor problem with a couple debug printfs.
o Default to a sane media type when none is reported.
o Minor style changes
The PR complains this will fix the IBM 300GL cards.
Submitted by: Max Gotlib
PR: 11462
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
attached and ifconfigable. The card doesn't interrupt yet.
Also, move towards bus space by introducing new macros/inline
functions which make such a move much easier than before.
These inline functions are setup now to work around an IBM EtherJet
pccard cardbus bridge incompatibility. The card works in 8 bit mode,
but not in 16-bit mode when it is connected to a cardbus bridge for
reasons unknown. The Linux driver also has a similar workaround in
it.
Future work will include making the above workaround runtime
conditional rather than compile time conditional, as well as fixing
the interrupts in pccards and converting it to bus space.
parts: isa and pccard. The isa one is known to work with an IBM
EtherJet ISA card. The pccard one isn't known to work because the
EtherJet pccard I purchased recently arrived DOA :-(. I'll commit the
pccard.conf entry when the replacement card arrives.
I plan on MFC this in a week or two.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
reported bug.
At using tcpdump for cs interface, tcpdump only dump packet which
src or dst MAC-address is cs interface. cs interface can't look up
packet between others.
Submitted by: MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
