Commit Graph

14 Commits

Author SHA1 Message Date
Nate Lawson
2813692cc2 Merge common XPT_CALC_GEOMETRY functions into a single convenience function.
Devices below may experience a change in geometry.

* Due to a bug, aic(4) never used extended geometry.  Changes all drives
  >1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.

For all other controllers in this commit, this should be a no-op.

Looked over by:	scottl
2003-06-14 22:17:41 +00:00
Justin T. Gibbs
a9fe95487e Sync perforce IDs. 2003-06-10 03:25:24 +00:00
Scott Long
7e71df9339 Bring back bus_dmasync_op_t. It is now a typedef to an int, though the
BUS_DMASYNC_ definitions remain as before.  The does not change the ABI,
and reverts the API to be a bit more compatible and flexible.  This has
survived a full 'make universe'.

Approved by:	re (bmah)
2003-05-27 04:59:59 +00:00
Justin T. Gibbs
d7cff4ab97 Correct spelling errors.
Switch to handling bad SCSI status as a sequencer interrupt
instead of having the kernel proccess these failures via
the completion queue.  This is done because:

 o The old scheme required us to pause the sequencer and clear
   critical sections for each SCB.  It seems that these pause
   actions, if coincident with a sequencer FIFO interrupt, would
   result in a FIFO interrupt getting lost or directing to the
   wrong FIFO.  This caused hangs when the driver was stressed
   under high "queue full" loads.
 o The completion code assumed that it was always called with
   the sequencer running.  This may not be the case in timeout
   processing where completions occur manually via
   ahd_pause_and_flushwork().
 o With this scheme, the extra expense of clearing critical
   sections is avoided since the sequencer will only self pause
   once all pending selections have cleared and it is not in
   a critical section.

  aic79xx.c
	Add code to handle the new BAD_SCB_STATUS sequencer
	interrupt code.  This just redirects the SCB through
	the already existing ahd_complete_scb() code path.
	Remove code in ahd_handle_scsi_status() that paused
	the sequencer, made sure that no selections where
	pending, and cleared critical sections.  Bad
	status SCBs are now only processed when all of these
	conditions are true.

  aic79xx.reg:
	Add the BAD_SCB_STATUS sequencer interrupt code.

  aic79xx.seq:
	When completing an SCB upload to the host, if
	we are doing this because the SCB contains non-zero
	SCSI status, defer completing the SCB until there
	are no pending selection events.  When completing
	these SCBs, use the new BAD_SCB_STATUS sequencer
	interrupt.  For all other uploaded SCBs (currently
	only for underruns), the SCB is completed via the
	normal done queue.  Additionally, keep the SCB that
	is currently being uploaded on the COMPLETE_DMA_SCB
	list until the dma is completed, not just until the
	DMA is started.  This ensures that the DMA is restarted
	properly should the host disable the DMA transfer for
	some reason.

	In our RevA workaround for Maxtor drives, guard against
	the host pausing us while trying to pause I/O until the
	first data-valid REQ by clearing the current snapshot
	so that we can tell if the transfer has completed prior
	to us noticing the REQINIT status.

	In cfg4data_intr, shave off an instruction before getting
	the data path running by adding an entrypoint to the
	overrun handler to also increment the FIFO use count.

	In the overrun handler, be sure to clear our LONGJMP
	address in both exit paths.

Perform a few sequencer optimizations.

  aic79xx.c:
	Print the full path from the SCB when a packetized
	status overrun occurs.

	Remove references to LONGJMP_SCB which is being
	removed from firmware usage.

	Print the new SCB_FIFO_USE_COUNT field in the
	per-SCB section of ahd_dump_card_state().  The
	SCB_TAG field is now re-used by the sequencer,
	so it no longer makes sense to reference this
	field in the kernel driver.

  aic79xx.h:
	Re-arrange fields in the hardware SCB from largest
	size type to smallest.  This makes it easier to
	move fields without changing field alignment.

	The hardware scb tag field is now down near the
	"spare" portion of the SCB to facilitate reuse
	by the sequencer.

  aic79xx.reg:
	Remove LONGJMP_ADDR.

	Rearrange SCB fields to match aic79xx.h.
	Add SCB_FIFO_USE_COUNT as the first byte
	of the SCB_TAG field.

  aic79xx.seq:
	Add a per-SCB "Fifos in use count" field and use
	it to determine when it is safe (all data posted)
	to deliver status back to the host.  The old method
	involved polling one or both FIFOs to verify that
	the current task did not have pending data.  This
	makes running down the GSFIFO very cheap, so we
	will empty the GSFIFO in one idle loop pass in
	all cases.

	Use this simplification of the completion process
	to prune down the data FIFO teardown sequencer for
	packetized transfers.  Much more code is now shared
	between the data residual and transfer complete cases.

	Correct some issues in the packetized status handler.
	It used to be possible to CLRCHN our FIFO before status
	had fully transferred to the host.  We also failed to
	handle NONPACKREQ phases that could occur should a CRC
	error occur during transmission of the status data packet.

Correct a few big endian issues:

  aic79xx.c:
  aic79xx_inline.h:
  aic79xx_pci.c:
  aic79xx_osm.c:
	o Always get the SCB's tag via the SCB_GET_TAG acccessor
	o Add missing use of byte swapping macros when touching
	  hscb fields.
	o Don't double swap SEEPROM data when it is printed.
	  Correct a big-endian bug.  We cannot assign a
	o When assigning a 32bit LE variable to a 64bit LE
	  variable, we must be explict about how the words
	  of the 64bit LE variable are initialized.  Cast to
	  (uint32_t*) to do this.

aic79xx.c:
	In ahd_clear_critical_section(), hit CRLSCSIINT
	after restoring the interrupt masks to avoid what
	appears to be a glitch on SCSIINT.  Any real SCSIINT
	status will be persistent and will immidiately
	reset SCSIINT.  This clear should only get rid of
	spurious SCSIINTs.

	This glitch was the cause of the "Unexpected PKT busfree"
	status that occurred under high queue full loads

	Call ahd_fini_scbdata() after shutdown so that
	any ahd_chip_init() routine that might access
	SCB data will not access free'd memory.

	Reset the bus on an IOERR since the chip doesn't
	seem to reset to the new voltage level without
	this.

	Change offset calculation for scatter gather maps
	so that the calculation is correct if an integral
	multiple of sg lists does not fit in the allocation
	size.

	Adjust bus dma tag for data buffers based on 39BIT
	addressing flag in our softc.

	Use the QFREEZE count to simplify ahd_pause_and_flushworkd().
	We can thus rely on the sequencer eventually clearing ENSELO.

	In ahd_abort_scbs(), fix a bug that could potentially
	corrupt sequencer state.  The saved SCB was being
	restored in the SCSI mode instead of the saved mode.
	It turns out that the SCB did not need to be saved at all
	as the scbptr is already restored by all subroutines
	called during this function that modify that register.

aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
	Add support for parsing the seeprom vital product
	data.  The VPD data are currently unused.

aic79xx.h:
aic79xx.seq:
aic79xx_pci.c:
	Add a firmware workaround to make the LED blink
	brighter during packetized operations on the H2A.

aic79xx_inline.h:
	The host does not use timer interrupts, so don't
	gate our decision on whether or not to unpause
	the sequencer on whether or not a timer interrupt
	is pending.
2003-05-04 00:20:07 +00:00
Maxime Henrion
7a648f56cf I deserve a big pointy hat for having missed all those references
to bus_dmasync_op_t in my last commit.
2003-04-10 23:50:06 +00:00
Jake Burkholder
ab89b20ced Compile with PAE. 2003-04-09 14:58:02 +00:00
Justin T. Gibbs
acae33b029 aic79xx.c:
Clear the LQICRC_NLQ status should it pop up after we have
	already handled the SCSIPERR.  During some streaming operations
	this status can be delayed until the stream ends.  Without this
	change, the driver would complain about a "Missing case in
	ahd_handle_scsiint".

	In the LQOBUSFREE handler...

		Don't return the LQOMGR back to the idle state until after
		we have cleaned up ENSELO and any status related to this
		selection.  The last thing we need is the LQO manager starting
		another select-out before we have updated the execution queue.
		It is not clear whether the LQOMGR would, or would not
		start a new selection early.

		Make sure ENSELO is off prior to clearing SELDO by flushing
		device writes.

		Move assignment of the next target SCB pointer inside of
		an if to make the code clearer.  The effect is the same.

	Dump card state in both "Unexpected PKT busfree" paths.

	In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
	That register only exists in the SCSI mode.  Also set the mode
	explicitly to the SCSI mode after chip reset due to paranoia.
	Re-arrange code so that SXFRCTL1 is restored as quickly after the
	chip reset as possible.

	S/G structurs must be 8byte aligned.  Make this official by saying
	so in our DMA tag.

	Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
	true.  This can cause a CIO bus lockup if a PCI or PCI-X error
	occurs while the stretch is occurring - the host cannot service
	the PCI-X error since the CIO bus is locked out and SHVALID will
	never resolve.  The stretch was added in the Rev B to simplify the
	wait for SHVALID to resolve, but the code to do this in the open
	source sequencer is so simple it was never removed.

	Consistently use MAX_OFFSET for the user max syncrate set from
	non-volatile storage.  This ensures that the offset does not
	conflict with AH?_OFFSET_UNKNOWN.

	Have ahd_pause_and_flushwork set the mode to ensure that it has
	access to the registers it checks.  Also modify the checking of
	intstat so that the check against 0xFF can actually succeed if
	the INT_PEND mask is something other than 0xFF.  Although there
	are no cardbus U320 controllers, this check may be needed to
	recover from a hot-plug PCI removal that occurs without informing
	the driver.

	Fix a typo.  sg_prefetch_cnt -> sg_prefetch_align.  This fixes
	an infinite loop at card initialization if the cacheline size is 0.

aic79xx.h:
	Add AHD_EARLY_REQ_BUG bug flag.

	Fix spelling errors.

	Include the CDB's length just after the CDB pointer in the DMA'ed
	CDB case.

	Change AH?_OFFSET_UNKNOWN to 0xFF.  This is a value that the
	curr->offset can never be, unlike '0' which we previously used.
	This fixes code that only checks for a non-zero offset to
	determine if a sync negotiation is required since it will fire
	in the unknown case even if the goal is async.

aic79xx.reg:
	Add comments for LQISTAT bits indicating their names in the 7902
	data book.  We use slightly different and more descriptive names
	in the firmware.

	Fix spelling errors.

	Include the CDB's length just after the CDB pointer in the DMA'ed
	CDB case.

aic79xx.seq:
	Update comments regarding rundown of the GSFIFO to reflect reality.

	Fix spelling errors.

	Since we use an 8byte address and 1 byte length, shorten the size
	of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.

	Remove code that, assuming the abort pending feature worked, would
	set MK_MESSAGE in the SCB's control byte on completion to catch
	invalid reselections.  Since we don't see interrupts for completed
	selections, this status update could occur prior to us noticing the
	SELDO.  The "select-out" queue logic will get confused by the
	MK_MESSAGE bit being set as this is used to catch packatized
	connections where we select-out with ATN.  Since the abort pending
	feature doesn't work on any released controllers yet, this code was
	never executed.

	Add support for the AHD_EARLY_REQ_BUG.  Don't ignore persistent REQ
	assertions just because they were asserted within the bus settle delay
	window.  This allows us to tolerate devices like the GEM318 that
	violate the SCSI spec.

	Remove unintentional settnig of SG_CACHE_AVAIL.  Writing this bit
	should have no effect, but who knows...

	On the Rev A, we must wait for HDMAENACK before loading additional
	segments to avoid clobbering the address of the first segment in
	the S/G FIFO.  This resolves data-corruption issues with certain
	IBM (now Hitachi) and Fujitsu U320 drives.

	Rearrange calc_residual to avoid an extra jmp instruction.

	On RevA Silicon, if the target returns us to data-out after we
	have already trained for data-out, it is possible for us to
	transition the free running clock to data-valid before the required
	100ns P1 setup time (8 P1 assertions in fast-160 mode).  This will
	only happen if this L-Q is a continuation of a data transfer for
	which we have already prefetched data into our FIFO (LQ/Data
	followed by LQ/Data for the same write transaction).  This can
	cause some target implementations to miss the first few data
	transfers on the bus.  We detect this situation by noticing that
	this is the first data transfer after an LQ (LQIWORKONLQ true),
	that the data transfer is a continuation of a transfer already
	setup in our FIFO (SAVEPTRS interrupt), and that the transaction
	is a write (DIRECTION set in DFCNTRL). The delay is performed by
	disabling SCSIEN until we see the first REQ from the target.

	Only compile in snapshot savepointers handler for RevA silicon
	where it is enabled.

	Handle the cfg4icmd packetized interrupt.  We just need to load
	the address and count, start the DMA, and CLRCHN once the transfer
	is complete.

	Fix an oversight in the overrun handler for packetized status
	operations.  We need to wait for either CTXTDONE or an overrun
	when checking for an overrun.  The previous code did not wait
	and thus could decide that no overrun had occurred even though
	an overrun will occur on the next data-valid req.  Add some
	comment to this section for clarity.

	Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
	completion in the packetized status case.  LASTSDONE may come up
	more quickly since it only records completion on the SCSI side,
	but since LAST_SEG_DONE is used everywhere else (and needs to be),
	this is less confusing.

	Add a missing invalidation of the longjmp address in the non-pack
	handler.  This code needs additional review.

aic79xx_inline.h:
	Fix spelling error.

aic79xx_osm.c:
	Set the cdb length for CDBs dma'ed from host memory.

	Add a comment indicating that, should CAM start supporting cdbs
	larger than 16bytes, the driver could store the CDB in the status
	buffer.

aic79xx_pci.c:
	Add a table entry for the 39320A.

	Added a missing comma to an error string table.

	Fix spelling errors.
2003-02-27 23:23:16 +00:00
Justin T. Gibbs
0794987d01 aic79xx.c:
Implement the SCB_SILENT flag.  This is useful for
	hushing up the driver during DV or other operations
	that we expect to cause transmission errors.  The
	messages will still print if the SHOW_MASKED_ERRORS
	debug option is enabled.

	Save and restore the NEGOADDR address when setting
	new transfer settings.  The sequencer performs lookups
	in the negotiation table too and it expects NEGOADDR
	to remain consistent across pause/unpause sessions.

	Consistently use "offset" instead of "period" to determine
	if we are running sync or not.

	Add a SHOW_MESSAGES diagnostic for when we assert ATN
	during message processing.

	Print out IU, QAS, and RTI features when showing transfer options.

	Limit the syncrate after all option conformance
	changes have taken place in ahd_devlimited_syncrate.
	Changes in options may change the final syncrate we
	accept.

	Keep a copy of the hs_mailbox in our softc so that
	we can perform read/modify/write operations on the
	hs_mailbox without having to pause the sequencer to
	read the last written value.  Use the ENINT_COALESS
	flag in the hs_mailbox to toggle interrupt coalessing.

	Add entrypoints for enabling interrupt coalessing and
	setting both a timeout (how long to wait for commands
	to be coalessed) and a maximum commands to coaless value.
	Add a statistics timer that decides when to enable or
	disable interrupt coalessing based on load.

	Add a routine, ahd_reset_cmds_pending() which is used
	to update the CMDS_PENDING sequencer variable whenever
	error recovery compeltes SCBs without notifying the
	sequencer.  Since ahd_reset_cmds_pending is called
	during ahd_unpause() only if we've aborted SCBs, its
	call to ahd_flush_qoutfifo should not cause recursion
	through ahd_run_qoutfifo().  A panic has been added to
	ensure that this recursion does not occur.

	In ahd_search_qinfifo, update the CMDS_PENDING sequencer
	variable directly.  ahd_search_qinififo can be called
	in situations where using ahd_reset_cmds_pending() might
	cause recursion.  Since we can safely determine the
	exact number to reduce CMDS_PENDING by in this scenario
	without running the qoutfifo, the manual update is sufficient.

	Clean up diagnostics.
	Add ahd_flush_qoutfifo() which will run the qoutfifo
	as well as complete any commands sitting on the
	sequencer's COMPLETE_SCB lists or the good status FIFO.
	Use this routine in several places that did similar
	things in an add-hoc, but incomplete, fashion.  A call
	to this routine was also added to ahd_abort_scbs() to
	close a race.

	In ahd_pause_and_flushwork() only return once selections
	are safely disabled.  Flush all completed commands via
	ahd_flush_qoutfifo().

	Remove "Now packetized" diagnostic now that this
	information is incorperated into the actual negotiation
	messages that are displayed.

	When forcing renegotiation, don't clober the current
	ppr_options.  Much of the driver uses this information
	to determine if we are currently packetized or not.

	Remove some stray spaces at column 1 in ahd_set_tags.

	When complaining about getting a host message loop
	request with no pending messages, print out the
	SCB_CONTROL register down on the card.

	Modify the ahd_sent_msg() routine to handle a search
	for an outgoing identify message.  Use this to detect
	a msg reject on an identify message which typically
	indicates that the target thought we were packetized.
	Force a renegotiation in this case.

	In ahd_search_qinfifo(), wait more effectively for SCB
	DMA activities to cease.  We also disable SCB fetch
	operations since we are about to change the qinfifo
	and any fetch in progress will likely be invalidated.

	In ahd_qinfifo_count(), fix the qinfifo empty case.

	In ahd_dump_card_state(), print out CCSCBCTL in the
	correct mode.

	If we are a narrow controller, don't set the current
	width to unknown when forcing a future negotiation.
	This just confuses the code into attempting a wide
	negotiation on a narrow bus.

	Add support for task management function completions.

	Modify ahd_handle_devreset so that it can handle
	lun resets in addition to target resets.  Use
	ahd_handle_devreset for lun and target reset task
	management functions.

	Handle the abort task TMF race case better.  We now
	wait until any current selections are over and then
	set the TMF back to zero.  This should cause the sequencer
	to ignore the abort TMF completion should it occur.

	Correct a bug in the illegal phase handler that
	caused us to drop down to narrow when handling the
	unexpected command phase case after 3rd party
	reset of a packetized device.

	Indicate the features, bugs, and flags set in the softc
	that are used to control firmware patch download when
        booting verbose.

aic79xx.h:
	Add coalessing and HS_MAILBOX fields.

	Add per-softc variables for the stats "daemon".

	Add a debug option for interrupt coalessing activities.

	Add two new softc flags:
	o AHD_UPDATE_PEND_CMDS
	  Run ahd_reset_cmds_pending() on the next unpause.

	o AHD_RUNNING_QOUTFIFO
	  Used to catch recursion through ahd_run_qoutfifo().

aic79xx.reg:
	Correct register addresses related to the software timer
	and the DFDBCTL register.

	Add constants paramaterizing the software timer.

	Add scratch ram locations for storing interrupt coalessing
	tunables.

	Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2.
	In at least the REV A, these are writable bits.  We make
	use of that for a swtimer workaround in the sequencer.

	Since HS_MAILBOX autoclears, provide a sequencer variable
	to store its contents.

	Add SEQINT codes for handling task management completions.

aic79xx.seq:
	Correct ignore wide residue processing check for
	a wide negotiation being in effect.  We must be
	in the SCSI register window in order to access the
	negotiation table.

	Use the software timer and a commands completed count to
	implement interrupt coalessing.  The command complete is
	deferred until either the maximum command threshold or a
	the expiration of a command deferral timer.  If we have
	more SCBs to complete to the host (sitting in COMPLETE_SCB
	lists), always try to coaless them up to our coalessing limit.
	If coalessing is enabled, but we have fewer commands oustanting
	than the host's min coalessing limit, complete the command
	immediately.

	Add code to track the number of commands outstanding.
	Commands are outstanding from the time they are placed
	into the execution queue until the DMA to post completion
	is setup.

	Add a workaround for intvec_2 interrupts on the H2A4.
	In H2A4, the mode pointer is not saved for intvec2, but
	is restored on iret.  This can lead to the restoration
	of a bogus mode ptr.  Manually clear the intmask bits and
	do a normal return to compensate.  We use intvec_2 to
	track interrupt coalessing timeouts.

	Since we cannot disable the swtimer's countdown, simply
	mask its interrupt once we no longer care about it firing.

	In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime
	we are notified of an HS_MAILBOX update via the
	HS_MAILBOX_ACT bit in QOFF_CTLSTA.  We have to use a
	local copy of persistant portions of the HS_MAILBOX as
	the mailbox auto-clears on any read.

	Move the test for the cfg4istat interrupt up an instruction
	to hopefully close a race between the next outgoing selection
	and our disabling of selections.

	Add a missing ret to the last instruction in load_overrun_buf.

	Add notifications to the host of task management
	completions as well as the completions for commands
	that completed successfully before their corresponding
	TMF could be sent.

	Hold a critical section during select-out processing
	until we have a fully identified connection.  This
	removes a race condition with the legacy abort handler.

	Correct a few spelling errors in some comments.

aic79xx_inline.h:
	Call ahd_reset_cmds_pending() in ahd_unpause if required.

	Update cmdcmplt interrupt statistics in our interrupt
	handler.

	Allow callers to ahd_send_scb() to set the task management
	function.

aic79xx_pci.c:
	Disable SERR and pause the controller prior to performing
	our mmapped I/O test.  The U320 controllers do not support
	"auto-access-pause".

aic79xx_osm.c:
	Set the task management function now that
	ahd_send_scb() doesn't do it for us.  We
	also perform a lun reset in response to BDR
	requests to packetized devices.
2003-01-20 20:17:35 +00:00
Scott Long
de5305d5b6 Synchronize perforce Id tags
Approved by:	re (blanket)
2002-11-30 20:04:10 +00:00
Scott Long
29dcbe8760 Revisit the printf format fixes for alpha. intmax_t doesn't exist in
RELENG_4, so cast to u_long in order to stay compatible.

Approved by: re	(blanket)
2002-11-28 04:09:29 +00:00
Scott Long
cec762959b Fix printf format problems that were stopping LINT on alpha
Submitted by:	jmallett, many others
Approved by:	re
2002-11-25 04:53:12 +00:00
Justin T. Gibbs
c1463ef7c0 Enable card interrupts in our OSM rather than in the core.
This ensures that we don't enter our interrupt handler until
all OSM components it might reference have been fully initialized
during attach.

Remove vestiges of untagged queue handling.

Add hints to ahd_get_scb() so it knows what type of SCB collision
management to perform for each new transaction.

Properly disable/enable IU_REQ with changes in tagged queuing and
disconnection settings passed in by CAM.
2002-08-31 06:51:15 +00:00
Justin T. Gibbs
cdd49e97b4 Hook up the ahd driver. 2002-06-06 16:35:58 +00:00
Justin T. Gibbs
17d2475554 Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X
SCSI Controller chip.
2002-06-05 19:52:45 +00:00