The HT40 channel population logic was "just" doing pairs of channels starting with
the band entry frequency. Trouble is, a lot of the rules start way off at 5120MHz,
which isn't a valid 5GHz channel. Then, eg for HT40U, it would populate:
* (5120,5140)
* (5160,5180)
* (5200,5220)
* (5240,5260)
.. as the HT40U pairs, with the first being the primary channel. Channel 36
is 5180MHz, and since it's not a primary channel here, it wouldn't populate it.
Then, the next HT40U would be 5200/5220, which is highly wrong.
HT40D had the same problem.
So, this just forces that 5GHz HT40 channels start at channel 36 (5180),
no matter what the band edge says. This includes eg doing 4.9GHz channels.
This erm, meant that the HT40 channels for the low band was always wrong.
Oops!
Tested:
* AR9380, STA mode
* AR9344 SoC, AP mode
MFC after: 1 week
This is important in hostap, ibss, (11s at some magical future date, etc)
where different nodes may have smaller limits.
Oops!
MFC after: 1 week
Relnotes: Yes
This adds a workaround to incorrectly behaving APs (ie, FreeBSD APs) which
don't beacon out exactly when they should (at TBTT multiples of beacon
intervals.)
It forces the hardware awake (but leaves it in network-sleep so self
generated frames still state that the hardware is asleep!) and will
remain awake until the next sleep transition driven by net80211.
That way if the beacons are just at the wrong interval, we get a much
better chance of hearing more consecutive beacons before we go to sleep,
thus not constantly disconnecting.
Tested:
* AR9485, STA mode, against a misbehaving FreeBSD AP.
The 802.11-2012 spec talks about this - section 10.1.3.2 - Beacon Generation
in Infrastructure Networks. So yes, we should be expecting beacons to be
going out in multiples of intval.
Silly adrian.
So:
* fix the FreeBSD APs that are sending beacons at incorrect TBTTs (target
beacon transmit time); and
* yes indeed we will have to wake up out of network sleep until we sync
a beacon.
This was being done in the pre-AR9380 case, but not for AR9380 and later.
When powersave in STA mode is enabled, this may have lead to the transmit
completion code doing this:
* call the task, which doesn't wake up the hardware
* complete the frames, which doesn't touch the hardware
* schedule pending frames on the hardware queue, which DOES touch the
hardware, and this will be ignored
This would show up in the logs like this:
(with debugging enabled):
Nov 27 23:03:56 lovelace kernel: Q1[ 0] (nseg=1) (DS.V:0xfffffe011bd57300 DS.P:0x49b57300) I: 168cc117 L:00000000 F:0005
...
(in general, doesn't require debugging enabled):
Nov 27 23:03:56 lovelace kernel: ath_hal_reg_write: reg=0x00000804, val=0x49b57300, pm=2
That register is a EDMA TX FIFO register (queue 1), and the val is the descriptor
being written.
Whilst here, make sure the software queue gets kicked here.
Tested;
* AR9485, STA mode + powersave
This bug has been bugging me for quite some time. I finally sat down
with enough coffee to figure it out.
The short of it - rounding up to the next intval multiple of the TSF value
only works if the AP is transmitting all its beacons on an interval of
the TSF. If it isn't - for example, doing staggered beacons on a multi-VAP
setup with a single hardware TSF - then weird things occur.
The long of it -
When powersave is enabled, the MAC and PHY are partially powered off.
They can't receive any packets (or transmit, for that matter.)
The target beacon timer programming will wake up the MAC/PHY just before
the beacon is supposed to be received (well, strictly speaking, at DTIM
so it can see the TIM - traffic information map - telling the STA whether
any traffic is there for it) and it happens automatically.
However, this relies on the target beacon time being programmed correctly.
If it isn't then the hardware will wake up and not hear any beacons -
and then it'll be asleep for said beacons. After enough of this, net80211
will give up and assume the AP went away.
This should fix both TSFOOR interrupts and disconnects from APs with powersave
enabled.
The annoying bit is that it only happens if APs stagger things or start
on a non-zero TSF. So, this would sometimes be fine and sometimes not be
fine.
What:
* I don't know (yet) why the code rounds up to the next intval.
For now, just disable rounding it and trust the value we get.
TODO:
* If we do see a beacon miss in STA mode then we should transition
out of sleep for a while so we can hear beacons to resync against.
I'd love a patch from someone to enable that particular behaviour.
Note - that doesn't require that net80211 brings the chip out of
sleep state - only that we wake the chip up through to full-on and
then let it go to sleep again when we've seen a beacon. The wifi
stack and AP can still completely just stay believing we're in sleep
mode.
Tested:
* AR9485, STA mode, powersave enabled
MFC after: 1 week
Relnotes: Yes
* Obey the peer A-MPDU density if it's larger than the currently configured
one.
* Pay attention to the peer A-MPDU max-size and don't assume we can transmit
a full A-MPDU (64k!) if the peer announces smaller values.
Relnotes: ath(4): Fix A-MPDU transmit; obey A-MPDU density and max size.
This is a long time coming. The general pieces have been floating around
in a local repo since circa 2012 when I dropped the net80211 support
into the tree.
This allows the per-chain RSSI and NF to show up in 'ifconfig wlanX list sta'.
I haven't yet implemented the EVM hookups so that'll show up; that'll come
later.
Thanks to Susie Hellings <susie@susie.id.au> who did the original work
on this a looong time ago for a company we both worked at.
* Don't do RTS/CTS - experiments show that we get ACK frames for each of them
and this ends up causing the timestamps to look all funny.
* Set the HAL_TXDESC_POS bit, so the AR9300 HAL sets up the hardware to return
location and CSI information.
* change the HT_RC_2_MCS to do MCS0..23
* Use it when looking up the ht20/ht40 array for bits-per-symbol
* add a clk_to_psec (picoseconds) routine, so we can get sub-microsecond
accuracy for the math
* .. and make that + clk_to_usec public, so higher layer code that is
returning clocks (eg the ANI diag routines, some upcoming locationing
experiments) can be converted to microseconds.
Whilst here, add a comment in ar5416 so i or someone else can revisit the
latency values.
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
The 11n duration calculation function in net80211 and the HAL round /up/
the duration calculation for short-gi, so we can't use that.
The 11n duration calculation doesn't know about the extra symbol time
needed for STBC, nor the LDPC encoding duration, so we can't use
that.
This (along with other, local hacks) allow the locationing services to
get down to around 200nS (yes, nanoseconds) of variance when speaking
to a "good" AP.
Tested:
* AR9380, STA mode, local locationing frame hacks
The pre-11n calculations include SIFS, but the 11n ones don't.
The reason is that (mostly) the 11n hardware is doing the SIFS calculation
for us but the pre-11n hardware isn't. This means that we're over-shooting
the times in the duration field for non-11n frames on 11n hardware, which
is OK, if not a little inefficient.
Now, this is all fine for what the hardware needs for doing duration math
for ACK, RTS/CTS, frame length, etc, but it isn't useful for doing PHY
duration calculations. Ie, given a frame to TX and its timestamp, what
would the end of the actual transmission time be; and similar for an
RX timestamp and figuring out its original length.
So, this adds a new field to the duration routines which requests
SIFS or no SIFS to be included. All the callers currently will call
it requesting SIFS, so this /should/ be a glorious no-op. I'm however
planning some future work around airtime fairness and positioning which
requires these routines to have SIFS be optional.
Notably though, the 11n version doesn't do any SIFS addition at the moment.
I'll go and tweak and verify all of the packet durations before I go and
flip that part on.
Tested:
* AR9330, STA mode
* AR9330, AP mode
* AR9380, STA mode
* the code already stored the length of the RX desc, which I never used.
So, use that and retire the new flag I introduced a while ago.
* Introduce a TX timestamp length field and capability.
* extend the TX timestamp to 32 bits, as the AR5416 and later does a full
32 bit TX timestamp instead of 15 or 16 bits.
* add RX descriptor fields for PHY uploaded information (coming soon)
* add flags for RX/TX fast timestamp, hardware upload, etc
* add a flag for TX to request ToD/ToA location information.
I keep asking myself "what do these fields mean" and so now I've clarified
it for myself.
Tested:
* Reading the comments, going "a-ha!" a couple times.
Approved by: re (gjb)
It turns out that getting decent performance requires stacking the TX
FIFO a little more aggressively.
* Ensure that when we complete a frame, we attempt to push a new frame
into the FIFO so TX is kept as active as it needs to be
* Be more aggressive about batching non-aggregate frames into a single
TX FIFO slot. This "fixes" TDMA performance (since we only get one
TX FIFO slot ungated per DMA beacon alert) but it does this by pushing
a whole lot of work into the TX FIFO slot.
I'm not /entirely/ pleased by this solution, but it does fix a whole bunch
of corner case issues in the transmit side and fix TDMA whilst I'm at it.
I'll go revisit transmit packet scheduling in ath(4) post 11.
Tested:
* AR9380, STA mode
* AR9580, hostap mode
* AR9380, TDMA client mode
Approved by: re (hrs)
This started showing up when doing lots of aggregate traffic. For TDMA it's
always no-ACK traffic and I didn't notice this, and I didn't notice it
when doing 11abg traffic as it didn't fail enough in a bad way to trigger
this.
This showed up as the fifo depth being < 0.
Eg:
Jun 19 09:23:07 gertrude kernel: ath0: ath_tx_edma_push_staging_list: queued 2 packets; depth=2, fifo depth=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1, bf=0xfffffe000385f068, start=1, end=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1: FIFO depth is now 0 (1)
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1, bf=0xfffffe0003866fe8, start=0, end=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1: FIFO depth is now -1 (0)
So, clear the flags before adding them to a TX queue, so if they're
re-added for the retransmit path it'll clear whatever they were and
not double-account the FIFOEND flag. Oops.
Tested:
* AR9380, STA mode, 11n iperf testing (~130mbit)
Approved by: re (delphij)
It turns out the frame scheduling policies (eg DBA_GATED) operate on
a single TX FIFO entry. ASAP scheduling is fine; those frames always
go out.
DBA-gated sets the TX queue ready when the DBA timer fires, which triggers
a beacon transmit. Normally this is used for content-after-beacon queue
(CABQ) work, which needs to burst out immediately after a beacon.
(eg broadcast, multicast, etc frames.) This is a general policy that you
can use for any queue, and Sam's TDMA code uses it.
When DBA_GATED is used and something like say, an 11e TX burst window,
it only operates on a single TX FIFO entry. If you have a single frame
per TX FIFO entry and say, a 2.5ms long burst window (eg TDMA!) then it'll
only burst a single frame every 2.5ms. If there's no gating (eg ASAP) then
the burst window is fine, and multiple TX FIFO slots get used.
The CABQ code does pack in a list of frames (ie, the whole cabq) but
up until this commit, the normal TX queues didn't. It showed up when
I started to debug TDMA on the AR9380 and later.
This commit doesn't fix the TDMA case - that's still broken here, because
all I'm doing here is allowing 'some' frames to be bursting, but I'm
certainly not filling the whole TX FIFO slot entry with frames.
Doing that 'properly' kind of requires me to take into account how long
packets should take to transmit and say, doing 1.5 or something times that
per TX FIFO slot, as if you partially transmit a slot, when it's next
gated it'll just finish that TX FIFO slot, then not advance to the next
one.
Now, I /also/ think queuing a new packet restarts DMA, but you have to
push new frames into the TX FIFO. I need to experiment some more with
this because if it's really the case, I will be able to do TDMA support
without the egregious hacks I have in my local tree. Sam's TDMA code
for previous chips would just kick the TXE bit to push along DMA
again, but we can't do that for EDMA chips - we /have/ to push a new
frame into the TX FIFO to restart DMA. Ugh.
Tested:
* AR9380, STA mode
* AR9380, hostap mode
* AR9580, hostap mode
Approved by: re (gjb)
Some later code I'll commit pushes lists of frames into the EDMA TX
FIFO, rather than a single frame at a time. The CABQ code already
pushes frame lists, but it turns out we should actually be doing it
in general or performance tanks. :(
This is the initial framework to call into the MCI HAL routines and drive
the basic state engine.
The MCI bluetooth coex model uses a command channel between wlan and
bluetooth, rather than a 2-wire or 3-wire signaling protocol to control things.
This means the wlan and bluetooth chip exchange a lot more information and
signaling, even at the per-packet level. The NICs in question can share
the input LNA and output PA on the die, so they absolutely can't stomp
on each other in a silly fashion. It also allows for the bluetooth side
to signal when profiles come and go, so the driver can take appropriate
control. There's also the possibility of dynamic bluetooth/wlan duty cycle
control which I haven't yet really played with.
It configures things up with a static "wlan wins everything" coexistence,
configures up the available 2GHz channel map for bluetooth, sets a static
duty cycle for bluetooth/wifi traffic priority and drives the basics needed to
keep the MCI HAL code happy.
It doesn't do any actual coexistence except to default to "wlan wins everything",
which at least demonstrates that things do indeed work. Bluetooth inquiry frames
still trump wifi (including beacons), so that demonstrates things really do
indeed seem to work.
Tested:
* AR9462 (WB222), STA mode + bt
* QCA9565 (WB335), STA mode + bt
TODO:
* .. the rest of coexistence. yes, bluetooth, not people. That stuff's hard.
* It doesn't do the initial BT side calibration, which requires a WLAN chip
reset. I'll fix up the reset path a bit more first before I enable that.
* The 1-ant and 2-ant configuration bits aren't being set correctly in
if_ath_btcoex.c - I'll dig into that and fix it in a subsequent commit.
* It's not enabled by default for WB222/WB225 even though I believe it now
can be - I'll chase that up in a subsequent commit.
Obtained from: Qualcomm Atheros, Linux ath9k
The legacy bits are just from ah.h; the MCI bits are from the ar9300
HAL "freebsd" extras.
A subsequent commit will include ah_btcoex.h into ah.h and remove
the older defintions.
This is like the WB222 coexistence (ie, "MCI", a message bus inside the
chip), and it's currently a cut/paste so I can start using it to flesh
out the differences with WB222.
It doesn't completely /do/ bluetooth coexistence, because it turns out
I need to add some contigmalloc'ed buffers to the btcoex path for this
type of hardware. I'm putting this work in the "people would like
to see functioning-ish btcoex before FreeBSD-11" bucket because I see
this as "broken".
Tested:
* QCA9535 (WB335) NIC, BT + 2GHz STA
