Differences between how paging is done on Solaris and Linux can cause
deadlocks if KM_SLEEP is used in any the following contexts.
* The txg_sync thread
* The zvol write/discard threads
* The zpl_putpage() VFS callback
This is because KM_SLEEP will allow for direct reclaim which may result
in the VM calling back in to the filesystem or block layer to write out
pages. If a lock is held over this operation the potential exists to
deadlock the system. To ensure forward progress all memory allocations
in these contexts must us KM_PUSHPAGE which disables performing any I/O
to accomplish the memory allocation.
Previously, this behavior was acheived by setting PF_MEMALLOC on the
thread. However, that resulted in unexpected side effects such as the
exhaustion of pages in ZONE_DMA. This approach touchs more of the zfs
code, but it is more consistent with the right way to handle these cases
under Linux.
This is patch lays the ground work for being able to safely revert the
following commits which used PF_MEMALLOC:
21ade34 Disable direct reclaim for z_wr_* threads
cfc9a5c Fix zpl_writepage() deadlock
eec8164 Fix ASSERTION(!dsl_pool_sync_context(tx->tx_pool))
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
The performance of the ZIL is usually the main bottleneck when dealing with
synchronous, write-heavy workloads (e.g. databases). Understanding the
behavior of the ZIL is required to diagnose performance issues for these
workloads, and to tune ZIL parameters (like zil_slog_limit) accordingly.
This commit adds a new kstat page dedicated to the ZIL with some counters
which, hopefully, scheds some light into what the ZIL is doing, and how it is
doing it.
Currently, these statistics are available in /proc/spl/kstat/zfs/zil.
A description of the fields can be found in zil.h.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#786
zil_slog_limit specifies the maximum commit size to be written to the separate
log device. Larger commits bypass the separate log device and go directly to
the data devices.
The optimal value for zil_slog_limit directly depends on the latency and
throughput characteristics of both the separate log device and the data disks.
Small synchronous writes are faster on low-latency separate log devices (e.g.
SSDs) whereas large synchronous writes are faster on high-latency data disks
(e.g. spindles) because of higher throughput, especially with a large array.
The point is, the line between "small" and "large" synchronous writes in this
scenario is heavily dependent on the hardware used. That's why it should be
made configurable.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#783
Moving the zil_free() cleanup to zil_close() prevents this
problem from occurring in the first place. There is a very
good description of the issue and fix in Illumus #883.
Reviewed by: Matt Ahrens <Matt.Ahrens@delphix.com>
Reviewed by: Adam Leventhal <Adam.Leventhal@delphix.com>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@nexenta.com>
Reivewed by: Dan McDonald <danmcd@nexenta.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References to Illumos issue and patch:
- https://www.illumos.org/issues/883
- https://github.com/illumos/illumos-gate/commit/c9ba2a43cb
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #340
This commit adds module options for all existing zfs tunables.
Ideally the average user should never need to modify any of these
values. However, in practice sometimes you do need to tweak these
values for one reason or another. In those cases it's nice not to
have to resort to rebuilding from source. All tunables are visable
to modinfo and the list is as follows:
$ modinfo module/zfs/zfs.ko
filename: module/zfs/zfs.ko
license: CDDL
author: Sun Microsystems/Oracle, Lawrence Livermore National Laboratory
description: ZFS
srcversion: 8EAB1D71DACE05B5AA61567
depends: spl,znvpair,zcommon,zunicode,zavl
vermagic: 2.6.32-131.0.5.el6.x86_64 SMP mod_unload modversions
parm: zvol_major:Major number for zvol device (uint)
parm: zvol_threads:Number of threads for zvol device (uint)
parm: zio_injection_enabled:Enable fault injection (int)
parm: zio_bulk_flags:Additional flags to pass to bulk buffers (int)
parm: zio_delay_max:Max zio millisec delay before posting event (int)
parm: zio_requeue_io_start_cut_in_line:Prioritize requeued I/O (bool)
parm: zil_replay_disable:Disable intent logging replay (int)
parm: zfs_nocacheflush:Disable cache flushes (bool)
parm: zfs_read_chunk_size:Bytes to read per chunk (long)
parm: zfs_vdev_max_pending:Max pending per-vdev I/Os (int)
parm: zfs_vdev_min_pending:Min pending per-vdev I/Os (int)
parm: zfs_vdev_aggregation_limit:Max vdev I/O aggregation size (int)
parm: zfs_vdev_time_shift:Deadline time shift for vdev I/O (int)
parm: zfs_vdev_ramp_rate:Exponential I/O issue ramp-up rate (int)
parm: zfs_vdev_read_gap_limit:Aggregate read I/O over gap (int)
parm: zfs_vdev_write_gap_limit:Aggregate write I/O over gap (int)
parm: zfs_vdev_scheduler:I/O scheduler (charp)
parm: zfs_vdev_cache_max:Inflate reads small than max (int)
parm: zfs_vdev_cache_size:Total size of the per-disk cache (int)
parm: zfs_vdev_cache_bshift:Shift size to inflate reads too (int)
parm: zfs_scrub_limit:Max scrub/resilver I/O per leaf vdev (int)
parm: zfs_recover:Set to attempt to recover from fatal errors (int)
parm: spa_config_path:SPA config file (/etc/zfs/zpool.cache) (charp)
parm: zfs_zevent_len_max:Max event queue length (int)
parm: zfs_zevent_cols:Max event column width (int)
parm: zfs_zevent_console:Log events to the console (int)
parm: zfs_top_maxinflight:Max I/Os per top-level (int)
parm: zfs_resilver_delay:Number of ticks to delay resilver (int)
parm: zfs_scrub_delay:Number of ticks to delay scrub (int)
parm: zfs_scan_idle:Idle window in clock ticks (int)
parm: zfs_scan_min_time_ms:Min millisecs to scrub per txg (int)
parm: zfs_free_min_time_ms:Min millisecs to free per txg (int)
parm: zfs_resilver_min_time_ms:Min millisecs to resilver per txg (int)
parm: zfs_no_scrub_io:Set to disable scrub I/O (bool)
parm: zfs_no_scrub_prefetch:Set to disable scrub prefetching (bool)
parm: zfs_txg_timeout:Max seconds worth of delta per txg (int)
parm: zfs_no_write_throttle:Disable write throttling (int)
parm: zfs_write_limit_shift:log2(fraction of memory) per txg (int)
parm: zfs_txg_synctime_ms:Target milliseconds between tgx sync (int)
parm: zfs_write_limit_min:Min tgx write limit (ulong)
parm: zfs_write_limit_max:Max tgx write limit (ulong)
parm: zfs_write_limit_inflated:Inflated tgx write limit (ulong)
parm: zfs_write_limit_override:Override tgx write limit (ulong)
parm: zfs_prefetch_disable:Disable all ZFS prefetching (int)
parm: zfetch_max_streams:Max number of streams per zfetch (uint)
parm: zfetch_min_sec_reap:Min time before stream reclaim (uint)
parm: zfetch_block_cap:Max number of blocks to fetch at a time (uint)
parm: zfetch_array_rd_sz:Number of bytes in a array_read (ulong)
parm: zfs_pd_blks_max:Max number of blocks to prefetch (int)
parm: zfs_dedup_prefetch:Enable prefetching dedup-ed blks (int)
parm: zfs_arc_min:Min arc size (ulong)
parm: zfs_arc_max:Max arc size (ulong)
parm: zfs_arc_meta_limit:Meta limit for arc size (ulong)
parm: zfs_arc_reduce_dnlc_percent:Meta reclaim percentage (int)
parm: zfs_arc_grow_retry:Seconds before growing arc size (int)
parm: zfs_arc_shrink_shift:log2(fraction of arc to reclaim) (int)
parm: zfs_arc_p_min_shift:arc_c shift to calc min/max arc_p (int)
It's possible for a zvol_write thread to enter direct memory reclaim
while holding open a transaction group. This results in the system
attempting to write out data to the disk to free memory. Unfortunately,
this can't succeed because the the thread doing reclaim is holding open
the txg which must be closed to be synced to disk. To prevent this
the offending allocation is marked KM_PUSHPAGE which will prevent it
from attempting writeback.
Closes#191
Fix non-c90 compliant code, for the most part these changes
simply deal with where a particular variable is declared.
Under c90 it must alway be done at the very start of a block.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
