Use this instead of DEBUG_LASTREQS to decide whether to log lock
requests.
MFS:
vinumlock: Catch a potential race condition where one process is
waiting for a lock, and between the time it is woken and
it retries the lock, another process gets it and places it
in the first entry in the table.
This problem has not been observed, but it's possible, and
it's easy enough to fix.
Submitted by: tegge
vinumunlock: Catch a real bug capable of hanging a system. When
releasing a lock, vinumunlock() called wakeup_one. This
caused wakeups to sometimes get lost. After due
consideration, we think that this is due to the fact that
you can't guarantee that some other process is also
waiting on the same address. This makes wakeup_one a
very dangerous function to use.
Requested by: bde
Add retryerrors keyword.
vinum_scandisk: Print a different message if an inadvertent start
command did not find any additional drives. The previous message "no
drives found" confused and worried many people.
MFS:
vinum_open: Recognize Mylex devices as storage devices.
In case of error, check the VF_RETRYERRORS flag in the subdisk and
don't take the subdisk down if it's set, just retry the I/O.
Requested by: peter
If the buffer has been copied (XFR_COPYBUF), release the copied
buffer when the I/O completes.
Suggested by: alfred
Desired by: bde
This commit is the first of a general cleanup of the header files..
It won't be enough to make bde happy.
Move debug definitions from vinumhdr.h.
Create a new struct rangelockinfo. In revision 1.21 of vinumlock.c,
the plex info was removed from struct rangelock, since it wasn't
needed there. It *is* needed for trace information, however, so use
struct rangelockinfo for that.
vm_mtx does not recurse and is required for most low level
vm operations.
faults can not be taken without holding Giant.
Memory subsystems can now call the base page allocators safely.
Almost all atomic ops were removed as they are covered under the
vm mutex.
Alpha and ia64 now need to catch up to i386's trap handlers.
FFS and NFS have been tested, other filesystems will need minor
changes (grabbing the vm lock when twiddling page properties).
Reviewed (partially) by: jake, jhb
copies out the current contents of the video buffer for a syscons terminal,
providing a snapshot of the text and attributes.
Based heavily on work originally submitted by Joel Holveck <joelh@gnu.org>
for 2.2.x almost 30 months ago, which I cleaned up a little, and forward
ported to -current.
See also the usr.bin/scrshot utility.
Pro and Raylink cards with version 5 firmware. Only infra-structure
mode has been tested. Specific changes for this feature are:
o Add RFC1042 encapsulation of IP datagrams
o Add authentication and association
o Decode of the beacon (although not used)
Other changes have been made:
o Pass command completion status to *_done (in place for
adding proper error recovery)
o Move a couple of state variables into the current
network parameters structure. This is in prep. for
dealing with roaming.
MFC after: 1 week
be unions with enough padding to make sure they always end up being
a multiple of 8 bytes in size, since the 83820/83821 chips require
descriptors to be aligned on 64-bit boundaries. I happened to get it
right for the 32-bit descriptor/x86 case, but botched everything else.
Things should work properle on 32-bit/64-bit platforms now.
Note that the 64-bit descriptor format isn't being used currently.
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.
aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
aic7xxx.c:
Remove linux header ifdefs.
current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.
Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.
if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);
becomes:
ahc_update_residual(scb);
Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.
Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.
In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.
Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.
When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.
Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.
Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.
Use SCSI-3 message terminology.
aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.
current -> curr
ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.
Update some serial eeprom definitions for the latest
BIOS versions.
aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.
aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.
Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.
On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.
aic7xxx_93cx6.c:
Remove linux header ifdefs.
aic7xxx_freebsd.c:
current -> curr
Add a module event handler.
Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.
aic7xxx_freebsd.h:
Include cleanups.
Define offsetof if required.
Correct a few comments.
Update prototype of ahc_send_async().
aic7xxx_inline.h:
Implement ahc_update_residual().
aic7xxx_pci.c:
Remove linux header ifdefs.
Correct a few product strings.
Enable several U160 performance enhancing features.
Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
of " &= ". Also change the MII PHY device mask to check the correct bits.
Cookie to: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Pointy hat to: me
. FD_CLRERR clears the error counter, thus re-enables kernel error
printf()s,
. FD_GSTAT obtains the last FDC operation state, if any,
. FDOPT_NOERRLOG (temporarily) turns off kernel printf() floppy
error logging,
. FDOPT_NOERROR makes the kernel ignore an FDC error, thus can
enable the transfer of an erroneous sector to the user application
All options are being cleared on (last) close.
Prime consumer of the last features will be fdread(1), to be committed
shortly.
(FD_CLRERR should be wired into fdcontrol(8), but then fdcontrol(8)
needs a major rewrite anyway.)
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
a LinkSys card here in the office where reading the station address
fails the first time, but works find afterwards. Without this, the
probe fails. I don't think this will negatively impact any existing
cards, but I want to confirm this before MFC'ing.
we need to delete the info from the list as well as zero out the res
pointer we saved in the code.
Also made a few style(9) changes while I was at it. Don't use if
(ptr) or if (!ptr), but compare against NULL. Compare against NULL
rather than 0. Don't have useless blocks.
There are likely other problems as well, but at least the wi based
wireless card with memory listed in its cis doesn't panic the system
when the card is inserted.
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
Reduce the verbose memory map setup reports and work with pccardd to
set the common memory map up.
Use enumeration values for CARD_SET_RES_FLAGS.
Use DELAY when spinning waiting for the card to come free instead of a loop.
MFC: after 1 week
Tidy up includes, credit Slawa Olhovchenkov, John Prince and Eric Hernes
for their efforts and add a couple of missing parenthesis around return
expressions.
- Rework of twe_report_request to use the command status value rather
than the flags register. (Joel Jacobson @ 3ware)
- Update to match some changes in -current vs. stable.
MFC in: 1 week
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
other "system" header files.
Also help the deprecation of lockmgr.h by making it a sub-include of
sys/lock.h and removing sys/lockmgr.h form kernel .c files.
Sort sys/*.h includes where possible in affected files.
OK'ed by: bde (with reservations)
The constant I was using was correct, but I mislabeled it as 256K when
it should have been 512K. This doesn't actually change the code, but
it clarifies things somewhat.
Submitted by: Chuck Cranor <chuck@research.att.com>
Add TI4451 as well.
These are untested since I don't have the hardware to test against.
Also, some O2Micro devices are #define w/o numbers as place holders so that
I can encourage people to submit them when they appear in the channels.
codecs. Also, add some additional code to check for future cards without
this feature - attempting to initialise them as AC97 cards will hang the
machine.
PR: 26427
Reviewed by: cg
s/1518/ETHER_MAX_LEN
Some style changes, add some braces, mostly residual from having
a lot of debug hooks added while working on this driver.
Bring in a plethora of changes from NetBSD:
revision 1.58
date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1
it wait until busy flag disappears.
it was able to prevent some cards with late initializing faling in wi_reset().
revision 1.41
date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2
Fix wi_intr() to avoid touching card registers during insert/remove events,
when sharing an interrupt with other devices:
check sc->sc_enabled, and drop the interrupt if its' off.
revision 1.30
date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4
Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header
instead of addr1 and addr2. THis means that tcpdump -e will show the
correct MAC address for communications with access points instead of showing
the BSSID.
In the future there should be 802.11 support for bpf/libpcap/tcpdump,
but that is aways down the road.
Parag Patel did all of the grunt work, so he gets the credit.
Register definitions and actions inferred from a Linux driver,
so Intel also gets some 'credit'.
o Change the number of init tries from 5 to a #define.
o Allow up to 5s rather than 2s for commands to complete. This
is still much less than 51 minutes, but makes my intel card init
with more reliability than before.
possible for some systems where the device is there, but the BIOS
hasn't allocated memory resources for it), we don't panic.
Submitted by: Gerard Roudier
Don't leak iospace when irq allocation fails. (call wi_free())
Call bus_release_resource() with the correct "rid" obtained from
bus_alloc_resource() that's saved in the softc instead of a hardcoded
0.
immediate value or the accumulator. 0 is the chip's internal
representation for the accumulator, and so 0 is an invalid immediate value
when the accumulator can also be specified as an argument.
Submitted by: gibbs
overflow the request queue. The reason we want to do this is that we
now push out completed CTIOs as we complete them- this gets the QLogic
working on them quicker. So we need to know whether we can put the entire
burrito out before we start.
We now support conjoint status with data for the last CTIO for both Fibre
Channel and SCSI. Leave the old code in place in case we need to go back
(minor 3 line ifdef).
Ultra-ultra important- *don't* set rq->req_seg_count for non-data
target mode requests in isp_pci_dmasetup. D'oh- this is actually
the tag value area for a CTIO. What *was* I thinking? Boy howdy
does both aic7xxx and sym get awfully unhappy when on reconnect
you give them a constant '1' for a tag value.
function- we did it a bit cleaner. We only use this if a CTIO completes with
!CT_OK state. We now have managed to get away without having to poke around
and trying to find the original ATIO- the csio we're using has the tag_id
and lun values with it which is mostly what we need when we do the putback.
Make sure we correctly propagate AT_TQAE->CT_TQAE for tags. Make sure
we call ISP_DMAFREE only if we had DATA to move.
tag is active for an ATIO, and say that you want to reconnect with
a tag value in a CTIO have *never* been exercised until now. This lossage
derived from Solaris code where this stuff originally came from that is
about 7 years old. Amazing.
We now bundle the incoming tag (legal values are 0..256) as the low
16 bits of the ccb_accept_tio's at_tagid while we put the firmware
handle for this ATIO in the top 16 bits- define some macros to make
this cleaner.
Complete some Ansification.
Redo establishment of default SCSI parameters whether or not
we've been compiled for target mode. Unfortunately, the Qlogic
f/w is confused so that if we set all targets to be 'safe' (i.e.,
narrow/async), it will also then report narrow, async if we're
contacted in target mode from that target (acting in initiator
role). D'oh!
Fix ISPCTL_TOGGLE_TMODE to correctly enable the right channel for
dual channel cards. Add some more opcodes. Fix a stupid NULL
pointer bug.
Simplify initialization and remove offending DMA channel resets there.
The resets trash whatever is pointed to DMA registers, but at cmi_attach()
time the DMA registers have not been initialized with valid addresses.
Reviewed by: Cameron Grant <gandalf@vilnya.demon.co.uk>
It appears that some of the new PRISM2 cards need it.
Fail the probe if we fail to read the MAC address.
Fix a comment.
Delete the unload printf. The bus system now prints this message.
