two loops in agp_generic_bind_memory(). As an intended side-effect, all
of the calls to vm_page_wakeup() are now performed with the containing
vm object lock held.
o Instead of locking and unlocking all over the place, use
lock assertions to make certain that the bfe lock is held
where necessary.
o Create locked and unlocked versions of bfe_init and bfe_start. These
functions can be called from outside the module and by functions
within the bfe module. The calls from outside the module don't
hold the bfe lock so the unlocked versions called by these functions
simple obtain the bfe lock and call the locked version.
- Fix a typo (scp) in the locking macros that only worked because in all the
instances in which it was called the softc pointer happened to be named 'sc'.
- Mark the interrupt MPSAFE
Tested by: matusita, Dario Freni <saturnero@gufi.org>
Silence from: -net, wpaul
with a weak memory model or x86 + PAE (or more specifically, your
driver is using bounce pages) and you have had problems with em(4),
this may fix it. At least this is needed to have em(4) work properly
on FreeBSD/arm.
Original version by: cognet
Reviewed by: tackerman
Tested by: cognet
Add constants for SPI protocol delays that are needed for
target mode.
aic7xxx.c:
Correct a target mode issue that caused an occassional
spurious REQ to be seen on the bus when performing manual
message processing (e.g. transfer rate negotiation).
Enforce phase change bus settle rules with explicit
delays when performing manual message processing in
target mode. The sequencer already did this for
"fast-path", target mode message processing.
as the original logic did. This fixes a race with vr_intr() which was
masked on UP systems and manifested on SMP systems.
PR: kern/62889
MFC after: 1 day
the ATA pccard locking function. This makes pccard devices like
Compact Flash cards work again.
PR: kern/72805
Submitted by: James E. Flemer <jflemer@alum.rpi.edu>
MFC in: 2 days
frames. BGE hardware with the rx alignment bug will still be handled by the
calls to m_adj() that already exist. m_adj() is probably better suited for
this task anyways. Just as with if_em, this saves a malloc + several locks
per packet and prevents unneeded data copying within busdma.
Since the e1000 DMA engines hava no constraints on the alignment of buffer
transfers, there is no reason to tell busdma that there is. This save a
minimum of 1 malloc call per packet, which translates to eliminating 4 locks.
It also means that buffers are not needlessly bounced when transfered. The
end result is a 38% improvement in pps in a 4 way bridging environment.
Obtained from: Sandvine, Inc.
(usually taking 20 seconds to transmit a packet).. no longer fall back
to only transmitting one packet (instead of the entire queue) after we
have processed the entire send queue... I have no idea why we didn't
start seeing this problem ~6 years ago when this code was introduced...
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
constrained to a small number of sessions by the small on-card memories found
in newer devices. This is really a stopgap solution as having session state
in main memory incurs a (small but noticeable) performance penalty. The better
solution is to manage session state so that it's cached on chip.
Obtained from: openbsd
The changes in the next commit would make the code totally unreadable
if the #ifdef'ing were maintained.
It might make a lot of sense to split if_cx.c in a netgraph related
and in a tty related file but I will not attempt that without hardware.
handle DMA addresses located above 1GB. The LBA(loop begin address)
register which holds DMA base address is 32bits register. But the
MSB 2bits are used for other purposes. This effectivly limits the
DMA address space up to 1GB.
Approved by: jake (mentor)
Reviewed by: truckman, matk
assign DMA address to the wrong address. It can cause system lockup
or other mysterious errors. Since most sound cards requires low DMA
address(BUS_SPACE_MAXADDR_24BIT) sndbuf_alloc() would fail when the
audio driver is loaded after long running of operations.
Approved by: jake (mentor)
Reviewed by: truckman, matk
