A attacker sending a lot of bogus fragmented packets to the target
(with different IPv4 identification field - ip_id), may be able
to put the target machine into mbuf starvation state.
By setting a upper limit on the number of reassembly queues we
prevent this situation.
This upper limit is controlled by the new sysctl
net.inet.ip.maxfragpackets which defaults to NMBCLUSTERS/4
If you want old behaviour (no upper limit) set this sysctl
to a negative value.
If you don't want to accept any fragments (not recommended)
set the sysctl to 0 (zero)
Obtained from: NetBSD (partially)
MFC after: 1 week
all alphas with devices behind ppb's. I'm working on a better solution now.
Note that all alphas that use per-platform interrupt mapping are broken
again (as they have been for several months)
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
any response to our third SYN to work-around some broken
terminal servers (most of which have hopefully been retired)
that have bad VJ header compression code which trashes TCP
segments containing unknown-to-them TCP options.
PR: kern/1689
Submitted by: jesper
Reviewed by: wollman
MFC after: 2 weeks
this works on cs4630 chips, and should implement the clkrun hack for
thinkpads- this will display diagnostic messages when triggered until its
correctness is established.
from cpu_switch(), curproc has been changed, but the sched_lock owner will
not be updated until we return to mi_switch(), thus we deadlock against
ourselves. As a workaround, push the acquire and release of sched_lock out
to the callers of set_user_ldt(). Note that we can't use a mtx_assert() in
set_user_ldt for the same reason.
Sleuting by: tmm
Tested by: tmm, dougb
For FTP control connection, keep the CRLF end-of-line termination
status in there.
Fixed the bug when the first FTP command in a session was ignored.
PR: 24048
MFC after: 1 week
* all members of msginfo from sysv_msg.c;
* msqids from sysv_msg.c;
* sema from sysv_sem.c; and
* shmsegs from sysv_shm.c;
These will be used by ipcs(1) in non-kvm mode.
Reviewed by: tmm
they can be used with cell operators like !.
As I did this, I noticed the whole CELL thing might have problems with
big endian architectures with sizeof(int)!=sizeof(void*).
UDP checksums too, not just IP. The chip only tells us if the checksum
is ok, it does not give us a copy of the partial checksum for later
processing. We have to deal with this the right way, but we can deal
with it.
- Use __func__ instead of __FUNCTION.
- Support power-off to S3 or S5 (takawata)
- Enable ACPI debugging earlier (with a sysinit)
- Fix a deadlock in the EC code (takawata)
- Improve arithmetic and reduce the risk of spurious wakeup in
AcpiOsSleep.
- Add AcpiOsGetThreadId.
- Simplify mutex code (still disabled).
attempting to remove nonexistant exports with MNT_DELEXPORT returns
an error; before this change it always succeeded. This caused
mountd(8) to log "can't delete exports for /whatever" warnings.
Change the error code from EINVAL to a more specific ENOENT, and
make mountd ignore this error when deleting the export list. I
could have just restored the previous behaviour of returning success,
but I think an error return is a useful diagnostic.
Reviewed by: phk
----
Make a device for each ISP- really usable only with devfs and add an ioctl
entry point (this can be used to (re)set debug levels, reset the HBA,
rescan the fabric, issue lips, etc).
----
Add in a kernel thread for Fibre Channel cards. The purpose of this
thread is to be woken up to clean up after Fibre Channel events
block things. Basically, any FC event that casts doubt on the
location or identify of FC devices blocks the queues. When, and
if, we get the PORT DATABASE CHANGED or NAME SERVER DATABASE CHANGED
async event, we activate the kthread which will then, in full thread
context, re-evaluate the local loop and/or the fabric. When it's
satisfied that things are stable, it can then release the blocked
queues and let commands flow again.
The prior mechanism was a lazy evaluation. That is, the next command
to come down the pipe after change events would pay the full price
for re-evaluation. And if this was done off of a softcall, it really
could hang up the system.
These changes brings the FreeBSD port more in line with the Solaris,
Linux and NetBSD ports. It also, more importantly, gets us being
more proactive about topology changes which could then be reflected
upwards to CAM so that the periph driver can be informed sooner
rather than later when things arrive or depart.
---
Add in the (correct) usage of locking macros- we now have lock transition
macros which allow us to transition from holding the CAM lock (Giant)
and grabbing the softc lock and vice versa. Switch over to having this
HBA do real locking. Some folks claim this won't be a win. They're right.
But you have to start somewhere, and this will begin to teach us how
to DTRT for HBAs, etc.
--
Start putting in prototype 2300 support. Add back in LIP
and Loop Reset as async events that each platform will handle.
Add in another int_bogus instrumentation point.
Do some more substantial target mode cleanups.
MFC after: 8 weeks
it becomes possible to trap in ptsstop() in kern/tty_pty.c
if the slave side has never been opened during the life of a kernel.
What happens is that calls to ttyflush() done from ptyioctl() for the
controlling side end up calling ptsstop() [via (*tp->t_stop)(tp, <X>)]
which evaluates the following:
struct pt_ioctl *pti = tp->t_dev->si_drv1;
In order for tp->t_dev to be set, the slave device must first be
opened in ttyopen() [kern/tty.c].
It appears that the only problem is calls to (*tp->t_stop)(tp, <n>),
so this could also happen with other ioctls initiated by the
controlling side before the slave has been opened.
PR: 27698
Submitted by: David Bein bein@netapp.com
MFC after: 6 days
it with vfsload("msdos").
(The proper fix would be to rename the `msdos' file system to
`msdosfs' in VFS_SET(), and mount_msdos(8) to mount_msdosfs(8).
But that would break too many existing fstab(5) setups, and
would require a lot of unnecessary documentation and code
msdos -> msdosfs changes.)
Noticed by: markm
csc_route and func_route to hold the way that each interrupt is
routed. csc is Card Status Change in the datasheets and standard, but
is called "Management Interrupt" in FreeBSDese. There are three types
of interrupt routing: ISA parallel, PCI parallel and ISA serial (some
chipsets support other types as well, but I don't plan on supporting
them).
When we try to allocate an interrupt, and the type for that interrupt
is pci_parallel, allow it to be shared by oring in RF_SHAREABLE to the
flags argument. Introduce pcic_alloc_resource to allow this to
happen.
file is processed by passing its name in argv[1]:
return(mod_loadobj(typestr, argv[1]));
however, it is not tested to see if argv[1] actually is defined.
At best, mod_loadobj() near line 244 returns an error like
"can't find 'garbage'" but if the "filename" entered is sufficiently
long, some buffer gets overrun. Of course, "load -t filename" is
actually a typo because we meant to type "load -t mfs_root filename";
nevertheless, a hung machine seems like too harsh a punishment for
such a small typo...
PR: i386/27693
Submitted by: Adrian Steinmann <ast@marabu.ch>
MFC after: 1 week
breakage:
- call PCIB_ROUTE_INTERRUPT() regardless of how valid the intline looks.
Some alphas leave garbage in the intline and leave the intr mapping
to OS platform support routines that map slots/buses to intlines
- Down in the alpha pci code, first try platform.pci_intr_route() and
if it doesn't exist or returns garbage, just read the intline out of
config space.
tested on AS500 (garbage in intline) and UP1000 (PC-like, intline is valid)
Note that a nice little hack like the APIC_IO section of pci_cfgregread()
is not workable. This is because the calling interface for
alpha_pci_route_interrupt() requires us to figure out the bus/slot/etc
from a device_t. At pci_read_device() time, we don't have a device_t
for the bus/slot/func in question.
instead of using two malloced arrays for storing channel lists, use an
slist. convert the sndstat device to use sbufs and optionally provide more
detail about channel state.
vchans are software mixed playback channels. they are not enabled by this
commit. they use the feeder infrastructure to emulate normal playback
channels in a manner transparent to applications, whilst providing as many
channels are desired, especially suitable for devices with only one hardware
playback channel. in the future they will provide additional features.
those wishing to test this functionality will need to add vchan.c to
sys/conf/files and use 'sysctl -w hw.snd.pcm0.vchans' to enable it.
blocksize and auto-rate selection are not yet supported.
SC_DEV isn't NULL; if it is, evaluate to NULL and don't dereference
NULL. Callers of VIRTUAL_TTY must already check for the result being
NULL since si_tty can be NULL, so this should be safe.
This fixes a panic when trying to switch to a different vty in an
environment such as userconfig (-c option to the kernel).
PR: 26508
the saved uid and gid during execve(). Unfortunately, the optimizations
were incorrect in the case where the credential was updated, skipping
the setting of the saved uid and gid when new credentials were generated.
This change corrects that problem by handling the newcred!=NULL case
correctly.
Reported/tested by: David Malone <dwmalone@maths.tcd.ie>
Obtained from: TrustedBSD Project
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
dev_t. The dev_depends(dev_t, dev_t) function is for tying them
to each other.
When destroy_dev() is called on a dev_t, all dev_t's depending
on it will also be destroyed (depth first order).
Rewrite the make_dev_alias() to use this dependency facility.
kern/subr_disk.c:
Make the disk mini-layer use dependencies to make sure all
relevant dev_t's are removed when the disk disappears.
Make the disk mini-layer precreate some magic sub devices
which the disk/slice/label code expects to be there.
kern/subr_disklabel.c:
Remove some now unneeded variables.
kern/subr_diskmbr.c:
Remove some ancient, commented out code.
kern/subr_diskslice.c:
Minor cleanup. Use name from dev_t instead of dsname()
