length field rather than the one byte message length field embedded
in the packet. This steps slightly outside of the protocol boundaries,
but should not cause any problems.
Limitation noted by: Simon Winwood <simon@winwood.org>
pkg_version (as you may well know) matches the existing packages/ports
installed on your system with the ports INDEX and reports which
ports differ from the current INDEX.
Submitted by: Bruce A. Mah <CA.Sandia.GOV>
Reviewed by: ports
- Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing
the initial work here. One thing I changed was to have the attach
and detach routines work like the PCI drivers, which means that in
theory you should be able to load and unload the driver like the PCI
NIC drivers, however the pccard support for this hasn't settled down
yet so it doesn't quite work. Once the pccard work is done, I'll have
to revisit this.
- Add device wi0 to PCCARD. If we're lucky, people should be able to
install via their WaveLAN cards now.
- Add support for signal strength caching. The wicontrol utility has
also been updated to allow zeroing and displaying the signal strength
cache.
- Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko.
Currently this module is only built for the i386 platform, though once
the pccard stuff is done it should be able to work on the alpha too.
(Theoretically you should be able to plug one of the WaveLAN/IEEE ISA
cards into an alpha with an ISA slot, but we'll see how that turns out.
- Update LINT to use only device wi0. There is no true ISA version of
the WaveLAN/IEEE so we'll never use an ISA attachment.
- Update files.i386 so that if_wi is dependent on card.
Previously, ppp attempted to bind() to a local domain tcp socket
based on the peer authname & enddisc. If it succeeded, it listen()ed
and became MP server. If it failed, it connect()ed and became MP
client. The server then select()ed on the descriptor, accept()ed
it and wrote its pid to it then read the link data & link file descriptor,
and finally sent an ack (``!''). The client would read() the server
pid, transfer the link lock to that pid, send the link data & descriptor
and read the ack. It would then close the descriptor and clean up.
There was a race between the bind() and listen() where someone could
attempt to connect() and fail.
This change removes the race. Now ppp makes the RCVBUF big enough on a
socket descriptor and attempts to bind() to a local domain *udp* socket
(same name as before). If it succeeds, it becomes MP server. If it
fails, it sets the SNDBUF and connect()s, becoming MP client. The server
select()s on the descriptor and recvmsg()s the message, insisting on at
least two descriptors (plus the link data). It uses the second descriptor
to write() its pid then read()s an ack (``!''). The client creates a
socketpair() and sendmsg()s the link data, link descriptor and one of
the socketpair descriptors. It then read()s the server pid from the
other socketpair descriptor, transfers any locks and write()s an ack.
Now, there can be no race, and a connect() failure indicates a stale
socket file.
This also fixes MP ppp over ethernet, where the struct msghdr was being
misconstructed when transferring the control socket descriptor.
Also, if we fail to send the link, don't hang around in a ``session
owner'' state, just do the setsid() and fork() if it's required to
disown a tty.
UDP idea suggested by: Chris Bennet from Mindspring at FreeBSDCon
happy with how this end up and will re-visit the entire empty field
problem, but this patch solves the NIS problem for now.
Submitted by: Dan Nelson <dan@emsphone.com>
PR: 14865,14984
/dev/usb. The actions are specified in the file /etc/usbd.conf.
usbd.c:
- Add event queue (/dev/usb) handling.
- Add comments
- Clean up code some more
usbd.8:
- Update manpage for the new command line flags
- Remove a duplicate FreeBSD tag from it).
usbd.conf, usbd.conf.5, Makefile:
- Add the usbd.conf configuration file and the man page for it.
NOTE: MAKEDEV already creates the /dev/usb device tree node, no change
needed there anymore.
inserting a new item. Without this, it's possible to
mis-insert quite badly... but only by as much as the load of
the first item, which is almost always 1 second.
Initialise the timerservice with `restart' set if we're inserting
at the start of the list.
- remove the use of NDEV. It is confusing. MAXUSBDEV should do.
- add some comments.
- add more explanation in usage()
- change the timeout value for undetected USB devices from 300 to 30
seconds. I don't think anyone wants to wait 5 minutes for broken
devices to show up. The overhead CPU wise is very little.
- print 'no controllers found' as a fatal error.
- remove inclusion of malloc.h. It's unused.
