Note when we've found a 8250 PNP node. Only try to set hw.uart.console
if we see one (otherwise ignore serial hints). The 8250 is the only
one known to have I/O ports, so limit the guessing to when we've
positively seen one. And limit this to x86 since that's the only
platform where we have I/O ports. Otherwise, we'd set the serial port
to something crazy for the platform and fall off the cliff early in
boot.
Differential Revision: https://reviews.freebsd.org/D16463
Add some verbose debugging information to the loader's new
choices. I'll remove these / put them behind a DEBUG define at a later
time. This is to give additional information if there's any dangling
edge cases not contemplated by the code. r336789 had most of this
change, but had the wrong commit message. This refines it slightly.
nodes. These show up in default entries on SuperMicro motherboards and
elsewhere. Before, we couldn't find a block device associated with the
device path and return BAD_CHOICE which was an instant
failure. However, a VendHw node isn't specifc, so when we don't find a
media path, return NOT_SPECIFIC so that the rest of the algorithms
work.
Sponsored by: Netflix.
loading.
If we are booting in a conforming UEFI Boot Manager Environment, then
use the BootCurrent variable to find the BootXXXX we're using. Once we
find that, then if it contains more than one EFI_DEVICE_PATH in its
what to boot section, try to use the last one as the kernel to
load. This will also set the default root partition as well. If
there's only one path, or if there's an error along the way, assume
that nothing specific was specified and revert to the old
algorithm. If something was specified, but not found, then fail the
boot. Otherwise you that, specific thing. On FreeBSD, this can be set
using efibootmgr -l <loader> -k <kernel>. We try a few variations of
kernel to cope with the fact that UEFI comes from a DOS world where
paths might be upper case and/or contain back-slashes.
Note: In an ideal world, we'd work out where we are in chain loading
by looking at the passed-in image handle and doing name
matching. However, that's unreliable since at least boot1.efi booted
images don't have that, hence the assumption that loader.efi needs to
load the last thing on the list, if possible.
The reason we fail for something specific is so that we can fully
participate in the UEFI Boot Manager Protocol and fail over to the
next item in the list of BootOrder choices when something goes wrong
at this stage.
This implements was was talked about in freebsd-arch@ last year
https://docs.freebsd.org/cgi/getmsg.cgi?fetch=3576+0+archive/2017/freebsd-arch/20171022.freebsd-arch
and documented in full (after changed resulting from the discussion) in
https://docs.google.com/document/d/1aK9IqF-60JPEbUeSAUAkYjF2W_8EnmczFs6RqCT90Jg/edit#
although one or two minor details may have been modified in this
implementation to make it work, and the ZFS MEDIA PATH extension isn't
implemented. This does not yet move things to ESP:\efi\freebsd\loader.efi.
RelNotes: Yes
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D16403
line args. I had thought console would be NULL, but it's efi. Set it
to efi (as a clue) before we initialize the console, then test it to
see if it changed on the command line to do the automatic
override. This gets my serial console back.
Setting rootdev in the enviornment should specify things
completely. If it is set, then have it override everything else.
PR: 229770
Differential Review: https://reviews.freebsd.org/D16322
o Fix the parsing of the device path. a last minute change terminated
it too soon.
o Kill setting LINES. We don't need to do it, and even if we did hard
coding it to 24 is wrong.
o Now that the console is working again for the loader, adjust the
printfs to be more in line with other platforms.
note that r336270's commit message was slightly incorrect. It changed
the default setting of the console to honor the ConOut
variable. Overrides via the command line are still possible, and we
use the devices in ConOut to set the proper console. If, for example,
serial cosnole is specified, we'll set console to "efi" if ConOut has
a serial port list and to either "efi comconsole" or "comconsole efi"
if not depending on whether -D or -D -h was specified.
RelNotes: Yes
Sponsored by: Netflix
For server machines, ComOut is set to the set of devices that the efi
console suppots. Parse it to see if we have serial, video or both.
Make that take precidence over the command line args. boot1.efi parses
them, but loader.efi doesn't. It's not clear where to read boot.conf
from, so we don't do that. The command line args can still be set via
efibootmgr, which is more inline with the UEFI boot manager to replace
that. These args are typically used only to set serial vs video and
the com speed line. We can infer that from ComOut, so do so.
Remember the com speed and hw.uart.console to match.
RelNotes: yes
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D15917
This moves the bulk of the geli support from lib386/biosdisk.c into a new
geli/gelidev.c which implements a devsw-type device whose dv_strategy()
function handles geli decryption. Support for all arches comes from moving
the taste-and-attach code to the devopen() function in libsa.
After opening any DEVT_DISK device, devopen() calls the new function
geli_probe_and_attach(), which will "attach" the geli code to the open_file
struct by creating a geli_devdesc instance to replace the disk_devdesc
instance in the open_file. That routes all IO for the device through the
geli code.
A new public geli_add_key() function is added, to allow arch/vendor-specific
code to add keys obtained from custom hardware or other sources.
With these changes, geli support will be compiled into all variations of
loader(8) on all arches because the default is WITH_LOADER_GELI.
Relnotes: yes
Sponsored by: Microchip Technology Inc
Differential Revision: https://reviews.freebsd.org/D15743
Eliminate 4 of the copies of the arg parsing in /boot/laoder
by using boot_parse_cmdline.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D16205
Move the libzfs stuff into libsa. There's no need for it to be a
separate library. The separate library adds to the issues of build
ordering that we see from time to time. Move the filesystem support
into libsa, like all the other filesystem support rather than making
zfs the odd-duck out.
Discussed with: allanjude@
table if we're just going to ignore it on arm, so expand, slightly,
the reach of the ifdef. Move the buffer to the inner block so we
don't have a separate #ifdef far away from these lines.
The issue on arm is that smbios_detect does unaligned accesses, which
in the u-boot implementing EFI context causes a crash.
is. We tell the ZFS code now, and it checks rather than having a
callback to do the checks.
This will allow us to have a more graceful fallback code. In the
future, it's anticipated that we may fallback to a more global search
(or implement a command to do so) when reqeusted by the user, or we
detect a violation of the UEFI Boot Manager protocol severe enough to
warrant this backstop. For now, it just allows us to get rid of img as
a global.
Sponsored by: Netflix
e.g. boot_mute, boot_single, boot_verbose, and friends; we checked for these
in multiple places, consolidate into common/ and allow a setting of "NO" for
any of these to turn them off. This allows systems with multiple
loader.conf(5) or loader.conf(5) overlay systems to easily turn off
variables in later processed files by setting it to NO.
Reported by: Nick Wolff @ iXsystems
Reviewed by: imp
- We should be setting a known graphics mode on conout, but we aren't.
- We shouldn't be setting gop mode if we didn't find a good resolution to
set, but we were. This made efi_max_resolution=1x1 effectively worthless,
since it would always set gop mode 0 if nothing else.
Refactor the currdev setting to find the device we booted from. Limit
searching when we don't already have a reasonable currdev from that to
the same device only. Search a little harder for ZFS volumes as that's
needed for loader.efi to live on an ESP.
Sponsored by: Netflix
Differential Review: https://reviews.freebsd.org/D13784
UGA does not have the same kind of mode enumeration that GOP does. Implement
it instead as a call to text_autoresize so that firmwares with only UGA
present still get some kind of autoresizing behavior.
While here, rename a typo'd "gop" to "uga", although it will remain unused
for the time being.
Not all systems use efifb; pull hw.vga.textmode and choose a good console
mode instead if it's set to something non-zero. This is basically a revival
of the code that used to live in boot1, but instead rebased onto this
different way of doing mode selection in loader.efi.
Interestingly enough, the regression that was previously introduced where
GOP would not reflect the console setting does not seem to exist when
console mode selection is done here. I've not done any investigation as to
why this is the case. Nevertheless, boot1.efi is still not the best place to
do mode selection.
Default the max resolution to 1080p, we'll accept Width x Height
specifications along with the following presets:
- 480p
- 720p
- 1080p
- 2160p or 4k
- 5k
PR: 224825
Differential Revision: https://reviews.freebsd.org/D14801
boot1 is too early to be deciding a good resolution. Console modes don't map
cleanly/predictably to actual screen resolutions, and GOP does not reflect
the actual screen resolution after a console mode change. Rip it out.
Add an efi-autoresizecons command to loader to choose an optimal screen
resolution based on the current environment. We'll explicitly execute this
later, preferably before we draw anything of value but after we load config
and pick up any tunables we may need to decide where we're going.
This method also allows us to actually pass the correct framebuffer
information on to the kernel.
UGA autoresizing is not implemented because it doesn't have the kind of mode
enumeration that GOP does. If an interested person with relevant hardware
could get in contact, we can take a look at implementing UGA autoresize.
This effectively "fixes" the breakage caused by r327058, but doesn't
actually set the resolution correctly until the interpreter calls
efi-autoresizcons. The lualoader version of this has been included for
reference; the forth equivalent will follow.
Reviewed by: imp (with some hestitation), manu
Differential Revision: https://reviews.freebsd.org/D14788
This fixes a problem encountered on the Lenovo Thinkpad X220/Yoga 11e where
runtime services would try to inexplicably jump to other parts of memory
where it shouldn't be when attempting to enumerate EFI vars, causing a
panic.
The virtual mapping is enabled by default and can be disabled by setting
efi_disable_vmap in loader.conf(5).
Reviewed by: kib (earlier version)
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D14677
A foolish consistency is the hobgoblin of little minds, adored by
little statesmen and philosophers and divines. With consistency a
great soul has simply nothing to do. -- Ralph Waldo Emerson
The current system is fragile and requires very careful layout of all
*_devdesc structures. It also makes it hard to change the base
devdesc. Take a page from CAM and put the 'header' in all the derived
classes and adjust the code to match.
For OFW, move the iHandle h_handle out of a slot conflicting with
d_opendata. Due to quirks in the alignment rules, this worked.
However changing the code to use d_opendata storage now that it's a
pointer is hard, so just have a separate field for it.
All other cleanups were to make the *_devdesc structures match where
they'd taken some liberties that were none-the-less compatible enough
to work.
open_disk uses d_opendata for it's own purpse. We can't store blkio
there. Fortunately, blkio is stored elsewhere and we never actually
retrieve blkio from d_opendata. Eliminate it as a source of confusion.
Eliminate all stores of d_opendata in efi since this layer doesn't own
that field.
There's no reason to have multiple copies of lszfs and
reloadbe. Consolidate them into one location. Also ldi_get_size is the
same everywhere (except sparc64). Make it the same everywhere as the
common definition is more general and will work on spar64.
Scan only the BLOCK IO MEDIA once instead of each time for each type of
device (fd, cd and hdd).
Leave the mechanism to free and reprobe all devices if one day we want
to implement a "dev rescan" thing.
Reviewed by: imp, tsoome
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14334
preference to LIBFICL{,32}. LIBFICL{,32} are now always defined, but
LDR_INTERP{,32} is defined empty when building w/o forth (aka the
simple interpreter) and defined to LIBFICL{,32} when we are building
forth.
MK_CTF, MK_SSP, MK_PROFILE, NO_PIC, and INTERNALLIB are always the
same, so set them in defs.mk. MAN= is common, so set it here too.
This removes a lot of boring repetition from the Makefiles that added
almost no value.
These were found during bring-up on a new arm64 platform and in an
amd64 VM.
Submitted by: Arshan Khanifar <arshankhanifar_gmail.com>
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14036
When building loader bits, lld fails with the following error:
"ld: error: section: .dynamic is not contiguous with other relro sections"
on both ubldr and EFI loader.
Move .dynamic up to make ld.lld happy, adjust .got as necessary for ubldr.
Tested on: OrangePi One (ld.lld, ubldr)
Tested on: Banana Pi-M3 (ld.lld, ubldr)
Tested on: qemu-armv7 (ld.lld, EFI)
Tested on: qemu-armv7 (ld.bfd, EFI)
Tested on: Raspberry Pi 2 (ld.bfd, ubldr) [manu]
Tested on: Banana Pi-M2 (ld.bfd, ubldr) [manu]
Reviewed by: andrew, emaste, imp
Differential Revision: https://reviews.freebsd.org/D13942
removing this argument, and expanding when rc is NULL. This
effectively completes the back out of custom scripts for tftp booted
loaders from r269153 that was started in r292344 with the new path
tricks that obsoleted it.
Submitted by: Netflix
