pnp system in freebsd, I'm not sure how useful this will be, but my
1542CP seems to work well in plug and play mode and does seem to
probe correctly at all the oddball addresses/irq/drqs that I tried.
[[
I was unable to get /kernel.conf or /kernel.config to read in, so
I wasn't able to verify that this method of userconfig works. that's
one thing that makes pnp so hard to use in the current scheme.
Pointers to the right new way of doing this accepted.
]]
o Add some kludges to maybe bring support for 1540A/1542A into the
driver. Since I have no 154xA cards, and the only person I know
that has them hasn't given me feedback, I'm making this commit
blind.
o Honor unit numbers that are in the config file now. This allows one
to hard wire the unit numbers (and have high unit numbers for plug
and pray devices, which can't seem to be hardwired) and have the
cards not migrate from aha1 -> aha0 should aha0 go on the fritz. I
didn't verify that hard wired scsi busses would work, but did verify
that hard wired aha addresses did work to a limited extent. Both
aha0 and aha1 must be hardwired, or when the card that was in aha0
goes away, the probe for aha0 might pick up the card that otherwise
would have been aha1.
its original form. (Originally, it only applied to the CFP 2107.)
Hopefully we can come to some conclusion about which Conner drives are
broken for tagged queueing.
The previous code just ignored the invalid map register, but this gave
surprising results because of the way pci_map_port() associated the map
register offset supplied with a map entry in the map array.
- Bring down the splash screen when a vty is opened for the first
time.
- Make sure the splash screen/screen saver is stopped before
switching vtys.
- Read and save initial values in the BIOS data area early.
VESA BIOS may change BIOS data values when switching modes.
- Fix missing '&' operator.
- Move ISA specific part of driver initialization to syscons_isa.c.
atkbd
- kbdtables.h is now in /sys/dev/kbd.
all
- Adjust for forthcoming alpha port. Submitted by: dfr
Fix NFS file corruption problem introduced in 1.188. The valid range
was not being set properly, causing a later reference to the buffer
to clear the B_CACHE bit.
the CFP2107, but it appears (not surprisingly) that the 1 gig and 4 gig
versions of that drive have the same problem with tagged queueing.
Also, fix the problem reported in PR kern/9482. The XPT_DEV_MATCH case in
xptioctl() wasn't putting a proper path in the CCB before it called
xpt_action(). When CAMDEBUG is defined, and CAM_DEBUG_TRACE debugging is
turned on, the CAM_DEBUG statement at the beginning of xpt_action would end
up deferencing a NULL path pointer. That of course caused a panic.
My solution is to just stick the xpt peripheral's path in the CCB.
PR: kern/9482
Reviewed by: gibbs
however is only marginally useful until the new-style bus (pci and isa)
stuff comes onboard to give us a better shot at actually pci and isa
drivers loadable (or preloadable anyway).
Iprobe is an alpha-only system profiling suite which I'm porting from
Linux/alpha to FreeBSD.
Iprobe works by using the hardware profiling support built into
alpha cpus. In a nutshell, what Iprobe does is to setup the alpha
performance counters to sample the pc at a fairly high rate & dumps
those pc samples out to user space. Then some code runs to map the
sampled PCs to functions. You get a bit more than that (like the PSL
word, so you can tell if you're in the kernel or userland, what the
ipl is, etc).
o Add the EB64PLUS systype into the kernel configuration files
and add it to the GENERIC kernel
o Correct mcclock_isa.c's dependence on cia, it should depend on isa.
This will allow avanti and eb64+ kernels to be built without the cia
chipset support code.
The new file pci_eb64plus_intr.s deals with the interrupt hardware
on the EB64PLUS and was obtained from NetBSD with the NetBSD
copyright intact
The apecs chipset support code was altered to allow routing interrupts
through pci if we're not running on an avanti. Avanti's route all
interrupts through isa.
Tested by: Wilko Bulte <wilko@yedi.iaf.nl>
Partially reviewed by: dfr
needs. This removes the dependancy on Perl for the generation of the
loader, allowing the world to be built on a perl-free system.
Submitted by: Joe Abley <jabley@clear.co.nz>
state.
Note: this requires a recompilation of netstat (but netstat has been
broken since rev 1.52 of ip_mroute.c anyway)
Obtained from: Significantly based on Steve McCanne's
<mccanne@cs.berkeley.edu> work for BSD/OS
arplookup() to try again. This gets rid of at least one user's
"arpresolve: can't allocate llinfo" errors, and arplookup() gives
better error messages to help track down the problem if there really
is a problem with the routing table.
one in the kernel source, and that one is already used for modules.
I don't _think_ this will hurt releases, aout-to-elf, etc, but it is
possible. In all the cases I've looked at, config(8) has been
generated straight after a make world, so if /usr/sbin/config exists and
is the right version for the kernel, then we can pretty much count on
/usr/bin/gensetdefs being there too.
XXX It probably makes sense to have a flag for bsd.kern.mk to avoid these
rules.
XXX IO_NDELAY seems to be the main reason for it, when used in a cdevsw
read or write "flag" context. Perhaps a redundant declaration
somewhere like sys/conf.h might help remove the need for vnode.h in
these device drivers in the first place.
