Since device can pass multiple frames in a single payload temporary
Rx buffer was big enough to hold all of them; now the driver can
concatenate a single frame from multiple payloads.
The Rx buffer size may be configured via tunable (dev.rtwn.%d.rx_buf_size).
Tested with:
- rtl8188cus, rtl8188eu and rtl8821au (STA mode).
- (by kevlo) rtl8192cu and rtl8188eu.
PR: 218527
Reviewed by: kevlo
Differential Revision: https://reviews.freebsd.org/D11705
the informational print functions. Collapse the debug API a bit to be
more generic and not require as much code duplication. While here, fix
a bug in MPS that was already fixed in MPR.
between 12/24 hour mode. Also fix conversion between 12 and 24 hour mode.
It's not as easy as adding/subtracting 12, because the clock doesn't roll
over 11->0, it rolls over 12->1; 0 isn't a valid hour in AM/PM mode.
Don't enable the oscillator when it is found to be stopped at init time,
just let the first setting of valid time start it. But still report a dead
battery if it's stopped at init time.
Don't force the chip into 24hr mode, just cope with whatever mode it is
already in.
Align the RTC clock to top of second when setting it.
Resource allocation for parent device does not look good by itself, but
attempt to allocate them for unrelated device just does not end up good.
On Asus X99-E WS/USB3.1 system reporting ISA bridge via both PCI and ACPI
this reported to cause kernel panic on shutdown due to messed resources:
https://bugs.freenas.org/issues/25237.
MFC after: 1 week
Do the allocation before requesting the IOCFacts message. This triggers
the LSI firmware to recognize the multiqueue should be enabled if available.
Multiqueue isn't used by the driver yet, but this also fixes a problem with
the cached IOCFacts not matching latter checks, leading to potential problems
with error recovery.
As a side-effect, fetch the driver tunables as early as possible.
Reviewed by: slm
Obtained from: Netflix
Differential Revision: D9243
all the chips in the NXP PCA212x and PCA/PCF85xx series. In addition to
supporting more chips, this driver uses the countdown timer on the chips as
a fractional seconds counter, giving it a resolution of about 15 milliseconds.
Use them in some existing code that is vulnerable to roundoff errors.
The existing constant SBT_1NS is a honeypot, luring unsuspecting folks into
writing code such as long_timeout_ns*SBT_1NS to generate the argument for a
sleep call. The actual value of 1ns in sbt units is ~4.3, leading to a
large roundoff error giving a shorter sleep than expected when multiplying
by the trucated value of 4 in SBT_1NS. (The evil honeypot aspect becomes
clear after you waste a whole day figuring out why your sleeps return early.)
Currently in Virtio driver without TSO/GSO features enabled, the max scatter
gather segments for the TX path can be 4, which limits the support for 9K JUMBO
frames. 9K JUMBO frames results in more than 4 scatter gather segments and
virtio driver fails to send the frame down to host OS. With TSO/GSO feature
enabled max scatter gather segments can be 64, then 9K JUMBO frames are fine,
this is making virtio driver to support JUMBO frames only with TSO/GSO.
Increasing the VTNET_MIN_TX_SEGS which is the case for non TSO/GSO to 32 to
support upto 64K JUMBO frames to Host.
Submitted by: Lohith Bellad <lohithbsd@gmail.com>
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8803
The ksyms(4) device was added specifically for use by lockstat(1), which
as a DTrace consumer must run as root.
Discussed with: emaste
MFC after: 3 days
queue lock when the uppoer stack is called inside TCP_LRO
Submitted by: Kevin Bowling <kevin.bowling@kev009.com>
Reviewed by: erj
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D11724
were redundant and not being used to set anything up.
Submitted by: Matt Macy <mmacy@mattmacy.io>
Reported by: Jeb Cramer <cramerj@intel.com>
Sponsored by: Limelight Networks
This largely reverts FreeBSD SVN change 289937 from October 25th, 2015.
The intent of that change was to keep loop IDs persistent across
chip reinits.
The problem is that the change turned on the PREVLOOP /
PREV_ADDRESS bit (bit 7 in Firmware Options 2), which tells the
Qlogic chip to not participate in the loop if it can't get the
requested loop address. It also turned off soft addressing on 2400
(4Gb) and newer controllers.
The isp(4) driver defaults to loop address 0, and the tape drives
I have tested default to loop address 0 if hard addressing is turned
on. So when hard loop addressing is turned on on the drive, the isp(4)
driver just refuses to participate in the loop.
The solution is to largely revert that change. I left some elements
in place that are related to virtual ports, since they were new.
This does work with IBM tape drives with hard and soft addressing
turned on. I have tested it with 4Gb, 8Gb, and 16Gb controllers.
sys/dev/isp.c:
Largely revert FreeBSD SVN change 289937. I left the
ispmbox.h changes in place.
Don't use the PREV_ADDRESS bit on initialization. It tells
the chip to not participate if it can't get the requested
loop ID.
Do use soft addressing on 2400 and newer chips.
Use hard addressing when the user has requested a specific
initiator ID. (hint.isp.X.iid=N in /boot/loader.conf)
Leave some of the virtual port options from that change in
place, but don't turn on the PREV_ADDRESS bit.
Reviewed by: mav
MFC after: 3 days
Sponsored by: Spectra Logic
Reduce the use of local copies of switch register data.
The switch now works with the upstream dsa node (i.e. the upstream DTS).
Tested on: ClearFog Pro (88E6176), SG-3100 (88E6141)
Sponsored by: Rubicon Communications, LLC (Netgate)
for embedded slots. Fail in the sdhci(4) initialization for slot type
shared, which is completely unsupported by this driver at the moment. [1]
For Intel eMMC controllers, taking the embedded slot type into account
obsoltes setting SDHCI_QUIRK_ALL_SLOTS_NON_REMOVABLE so remove these quirk
entries.
- Hide the 1.8 V VDD capability when the slot is detected as non-embedded,
as the SDHCI specification explicitly states that 1.8 V VDD is applicable
to embedded slots only. [2]
- Define some easy bits of the SDHCI specification v4.20. [3]
- Don't leak bus_dma(9) resources in failure paths of sdhci_init_slot().
Obtained from: DragonFlyBSD 65704a46 [1], 7ba10b88 [2], 0df14648 [3]
Usually it is sufficient to use iicbus_transfer_excl(), or one of the
higher-level convenience functions that use it, to reserve the bus for the
duration of each register access. Occasionally it is important that a
series of accesses or read-modify-write operations must be done without any
other intervening access to the device, to prevent corrupting state.
Without support for nested request/release, slave device drivers would have
to stop using high-level convenience functions and resort to working with
arrays of iic_msg structs just for a few operations (often involving
one-time device setup or infrequent configuration changes).
The changes here appear large from a glance at the diff, but in fact they're
nearly trivial, and the large diff is because of changes in indentation and
the re-wrapping of comments caused by that. One notable change is that
iicbus_release_bus() now ignores the IICBUS_CALLBACK(IIC_RELEASE_BUS) return
value. The old error handling left the bus in a kind of limbo state where
it was still owned at the iicbus layer, but drivers rarely check the return
of the release call, and it's unclear what they would do to recover from an
error return anyway. No existing low-level drivers return any kind of error
from IIC_RELEASE_BUS except one EINVAL for "you don't own the bus", to which
the right response is probably to carry on with the process of releasing the
reference to the bus anyway.
on i2c devices, where the "register" can be any length.
Many (perhaps most) common i2c devices are organized as a collection of
(usually 1-byte-wide) registers, and are accessed by first writing a 1-byte
register index/offset number, then by reading or writing the data.
Generally there is an auto-increment feature so the when multiple bytes
are read or written, multiple contiguous registers are accessed.
Most existing slave device drivers allocate an array of iic_msg structures,
fill in all the transfer info, and invoke iicbus_transfer(). These new
functions commonize all that and reduce register access to a simple call
with a few arguments.
* While there clean up alignments and line wrapping in existing
definitions for rs API in if_iwmreg.h
Obtained from: dragonflybsd.git 085e37a042bdb17081e495e46919359ce43aa118
* iwm_xmit_queue_drain() calls ieee80211_free_node(), removing a possible
memory leak, compared to using just mbufq_drain().
* Remove duplicate mbufq_drain() from iwm_mvm_rm_sta(), this should be
handled in the caller.
Obtained from: dragonflybsd.git 339d45fda40072e0aca5ece639173204716f11fe
* Limiting the channel list with "ifconfig wlan0 chanlist ..." now will
actually set the list of channels scanned by iwm.
Tested:
* Intel 7260, STA mode, setting chanlist to 1-14 and 36-254, and indeed it does what
it should!
of LOR detection and a bit of lock release/acquire collision when using LRO.
Submitted by: Kevin Bowling <kevin.bowling@kev009.com>
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D11712
and keepalive in the sysctl MIB. Provide tunables to change some of
these parameters. These are supposed to be setup by the firmware so
these tunables are for experimentation only.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
This status will be reported if the backend NIC is wireless; it's not
useful. Due to the high frequency of the reporting, this could be
pretty annoying; ignore it.
MFC after: 3 days
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D11651
The VF-HN map will be used later on to implement "transparent VF".
MFC after: 3 days
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D11618
