* to reduce the number of adapter failures. Transceiver select
* logic changed to use value from EEPROM. Autoconfiguration
* features added.
Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
Etherlink III 'zp' on 2.0R, but it did not work with the -current.
Noriyuki Takahashi <hor@aecl.ntt.jp> san has fixed this bug.
Our alpha-testers are tested this driver with 3C589B-COMBO and
3C589B-TP. And it works fine.
I also fixed a little about the use of ZP_DEBUG symbol and beautified
the awful Frankenstein-style indent :-) with "indent -c0 -nfc1 -i4".
[Also merge with Bruce's last changes]
Submitted by: "HOSOKAWA Tatsumi" <hosokawa@mt.cs.keio.ac.jp>
update what has actually been touched. This should speed up
screen access on slow hardware.
Introduced setting of "destructive" cursor size, much like
the old hardware cursor.
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
- ignore the partition table if it is identical with the bogus one in
/usr/src/sys/i386/boot/biosboot/start.S. Honoring the bogus size
field was fatal. The error is detected but other compatibilty
cruft weakens the error handling too much for this case.
- weaken the partition entry checking to allow the following treatments
of C/H/S addresses when C should be >= 1024:
(1) allow C = 1023, H = max, S = max.
(2) allow C to be correct modulo 1024.
Other compatibilty cruft weakens the error handling to allow all
C/H/S addresses, but there too many errors were reported.
Improve error messages:
- print C/H/S addresses if relevant.
- distinguish primary partition table from extended partition tables.
- don't use diskerr() except for i/o errors.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
Fixed the I/O statistics
Allow WD1007 type controllers to work
Support MULTI-BLOCK I/O
Correct delay to use port 0x84, reading the status register
might not be a long enough delay.
Changed probe message to match SCSI type devices.
with individual devices for each type of sound card:
opl, sb, sbxvi, sbmidi, pas, mpu, gus, gusxvi, gusmax, mss, uart
EXCLUDE_* options are no longer required to be included in the config file.
They are automatically determined by local.h depending on the devices
included.
Move #includes in local.h to os.h so files are included in the proper
order to avoid warnings.
soundcard.c now has additional code to reflect the device driver
routines needed.
Define new EXCLUDE_SB16MIDI for use in sb16_midi.c and dev_table.h.
#ifndef EXCLUDE_SEQUENCER or EXCLUDE_AUDIO have been added to
soundcard.c and sound_switch.c where appropriate.
Probe outputs changed to reflect new device names.
Readme.freebsd not needed. Update sound.doc with new config instructions.
Reviewed by: wollman
$Id$ information, and other code to make sound driver compile and work
correctly with FreeBSD.
Integrate changes obtained from Sujal Patel. These changes are:
o local.h: reverse option logic from EXCLUDE_* to AUDIO_*
o pas2_mixer.c: small addition
o ad1848.c: minor change with macro names
o sequencer.c: minor change with note check
o many spelling corrections in comments in about every other file
