upper stack in fxp_start_body().
fxp(4) drops driver lock in Rx path so check the fxp(4) is still
running after reacquiring driver lock in Rx path. Also don't
invoke fxp_intr_body if fxp(4) is not running. With this change
there is no need to set suspend bit in device attach phase.
hardware reset in attach phase. Selective reset does not clear
configured parameters so I think full hardware reset is required.
To prevent PCI bus lock-up, do selective reset first which will get
off the controller from PCI bus and request software reset after
selective reset. Software reset will unmask interrupts so disable
it after the reset.
common mbuf dma tag for both Tx and Rx path but Rx buffer should
have single DMA segment and maximum buffer size of the segment
should be less than MCLBYTES.
fxp(4) also have to check Tx completion status which was updated by
DMA so we need BUS_DMASYNC_PREREAD and BUS_DMASYNC_POSTWRITE
synchronization in Tx path. Fix all misuse of bus_dmamap_sync(9) in
fxp(4). I guess this change shall fix occasional driver breakage in
PAE environments.
While I'm here add error messages of dma tag/buffer creation and
correct messages.
getgroups for ibcs emulation. It seems vanishingly likely any
programs will actually be affected since they probably assume a much
lower value and use a static array size.
pointer to the containing mbuf. This eliminates a strong assumption
about the layout of network buffer memory, giving us greater
flexibility to revise mbuf semantics in the future.
reassembly but failed to be modernized over time:
- Use queue(9).
- Specifically allocate queue entries of type M_SPXREASSQ to point at
member mbufs, rather than casting mbuf data to 'spx_q'.
- Maintain the mbuf pointer as part of the queue entry so that we can
later free the mbuf without using dtom().
Intel agrees with my reading of the docs, make it so for all G4X chips.
The new register also has a 32 bit width as opposed to 24 bits. Fix
things up so that the counters roll over properly.
MFC after: 3 days
Now that we start to use credentials on character devices more often
(because of MPSAFE TTY), move the prison-checks that are in place in the
TTY code into devfs.
Instead of strictly comparing the prisons, use the more common
prison_check() function to compare credentials. This means that
pseudo-terminals are only visible in devfs by processes within the same
jail and parent jails.
Even though regular users in parent jails can now interact with
pseudo-terminals from child jails, this seems to be the right approach.
These processes are also capable of interacting with the jailed
processes anyway, through signals for example.
Reviewed by: kib, rwatson (older version)
not in cpu_exit(). The latter is called after td_md.md_highfp_mtx
has been destroyed, which results in a race condition when another
thread wants to use the high FP registers on the CPU that still has
the high FP registers in question.
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
below key_setsaval().
Without that, the lookup for the SA had failed as we were looking for
a SA with the new, updated port numbers instead of the old ones and
were comparing the ports in key_cmpsaidx().
This makes updating the remote -> local SA on the initiator work again.
Problem introduced with: p4 changeset 152114
Add necessary changes to the kernel for this (basically introduce a
bpf_zero_counters() function). As well, update the man page.
MFC after: 1 month
Discussed with: rwatson
NGROUPS_MAX, eliminate ABI dependencies on them, and raise the to 1024
and 1023 respectively. (Previously they were equal, but under a close
reading of POSIX, NGROUPS_MAX was defined to be too large by 1 since it
is the number of supplemental groups, not total number of groups.)
The bulk of the change consists of converting the struct ucred member
cr_groups from a static array to a pointer. Do the equivalent in
kinfo_proc.
Introduce new interfaces crcopysafe() and crsetgroups() for duplicating
a process credential before modifying it and for setting group lists
respectively. Both interfaces take care for the details of allocating
groups array. crsetgroups() takes care of truncating the group list
to the current maximum (NGROUPS) if necessary. In the future,
crsetgroups() may be responsible for insuring invariants such as sorting
the supplemental groups to allow groupmember() to be implemented as a
binary search.
Because we can not change struct xucred without breaking application
ABIs, we leave it alone and introduce a new XU_NGROUPS value which is
always 16 and is to be used or NGRPS as appropriate for things such as
NFS which need to use no more than 16 groups. When feasible, truncate
the group list rather than generating an error.
Minor changes:
- Reduce the number of hand rolled versions of groupmember().
- Do not assign to both cr_gid and cr_groups[0].
- Modify ipfw to cache ucreds instead of part of their contents since
they are immutable once referenced by more than one entity.
Submitted by: Isilon Systems (initial implementation)
X-MFC after: never
PR: bin/113398 kern/133867
Instead of locking the local unp followed by the remote unp, use the same
locking model as accept() and read lock the global link lock followed by
the remote unp while fetching the remote sockaddr.
Reported by: Mel Flynn mel.flynn of mailing.thruhere.net
Reviewed by: rwatson
MFC after: 1 week
structure. When the page is shared, the kernel mapping becomes a special
type of managed page to force the cache off the page mappings. This is
needed to avoid stale entries on all ARM VIVT caches, and VIPT caches
with cache color issue.
Submitted by: Mark Tinguely
Reviewed by: alc
Tested by: Grzegorz Bernacki, thompsa
allocator for the jumbo frames zones. This change has two benefits: (1) a
custom back-end deallocator is no longer required. UMA's standard
deallocator suffices. (2) It eliminates a potentially confusing artifact
of using contigmalloc(): The malloc(9) statistics contain bogus information
about the usage of jumbo frames. Specifically, the malloc(9) statistics
report all jumbo frames in use whereas the UMA zone statistics report the
"truth" about the number in use vs. the number free.
SVCXPTR structure returned by them, it was possible for the structure
to be free'd before svc_reg() had been completed using the structure.
This patch acquires a reference count on the newly created structure
that is returned by svc_[dg|vc|tli|tp]_create(). It also
adds the appropriate SVC_RELEASE() calls to the callers, except the
experimental nfs subsystem. The latter will be committed separately.
Submitted by: dfr
Tested by: pho
Approved by: kib (mentor)
in the type field of system call tables. Specifically, one can now use
the 'NO*' types as flags in addition to the 'COMPAT*' types. For example,
to tag 'COMPAT*' system calls as living in a KLD via NOSTD. The COMPAT*
type is required to be listed first in this case.
- Add new functions 'type()' and 'flag()' to the embedded awk script in
makesyscalls.sh that return true if a requested flag is found in the
type field ($3). The flag() function checks all of the flags in the
field, but type() only checks the first flag. type() is meant to be
used in the top-level "switch" statement and flag() should be used
otherwise.
- Retire the CPT_NOA type, it is now replaced with "COMPAT|NOARGS" using
the flags approach.
- Tweak the comment descriptions of COMPAT[46] system calls so that they
say "freebsd[46] foo" rather than "old foo".
- Document the COMPAT6 type.
- Sync comments in compat32 syscall table with the master table.
a potential race pointed out by pjd. Also use TAILQ_FOREACH_SAFE to iterate over
dirhashes in ufsdirhash_lowmem(), so that we can continue iterating even after a
dirhash is destroyed.
Suggested by: pjd
Tested by: pho
Approved by: dwmalone (mentor)
- Mark nfsclnt as UNIMPL. It should have been NOSTD instead of NOIMPL back
when it lived in nfsclient.ko, but it was removed from that a long time
ago.
