Fixed some style bugs (always use precisely 1 space after `:' in
dependency specifications).
Removed bogus dependency of ${FULLKERNEL} on ${BEFORE_DEPEND}.
is not configured. Including <isa/isavar.h> when it is not used is
harmful as well as bogus, since it includes "isa_if.h" which is not
generated when isa is not configured.
fixee incoherency of pipe timestamps relative to file timestamps in
the usual case where getnanotime() is not used for the latter. (File
and pipe timestamps are still incoherent relative to real time unless
the vfs_timestamp_precision sysctl is set to 2 or 3).
Some interface botches went away, leaving the macros unused outside of
the implementation of interrupt masking, and it was silly for the
implementation to use the macros in only one place each.
apm_default_resume() to sometimes set a very wrong time.
(1) Accesses to the RTC index and data registers were not atomic enough.
Interrupts were not masked. This was only good enough until an
interrupt handler (rtcintr()) started accessing the RTC in FreeBSD-2.0.
(2) Access to the block of time registers in inittodr() was not atomic
enough. inittodr() has 244us to read the time registers. Interrupts
were not masked. This was only good enough until something (apm)
started calling inittodr() after boot time in FreeBSD-2.0.
The fix for (2) also makes the timecounter update more atomic, although
this is currently unimportant due to the low resolution of the RTC.
Problem reported by: mckay
frames would be handled incorrectly due to bad usage of m_pullup() in
the case where the frame wraps from the end of the receive buffer back
the beginning.
Also, when manually extending small packets to pad them to the minimum
frame length during transmission, zero out the pad area to make some
really paranoid people happy.
when I made the absence of the clean flag sticky in rev.1.88. This
was a problem main for "mount /". There is no way to mount "/" for
writing without using mount -u (normally implicitly), so after
"mount -f /" of an unclean filesystem, the absence of the clean flag
was sticky forever.
each and every xxx_genassym.c file to seperately define these and
also to promote uniformity and a level of abstraction.
Symbols are created as unsigned long by default and overridable on
a per file basis.
- In uhci_intr() check to see if sc->sc_bus.bdev is NULL, and if it is,
ack any pending interrupts and disable them, then return. It is possible
for interrupts to be delivered the moment a handler is set up at attach
time in uhci_pci.c, particularly when attempting to kldload the usb.ko
module after the system is already up. However the driver isn't ready
to field interrupts at that time and certain pointers in the softc
struct aren't initialized yet, and we invariably end up falling off
the end of one of them. The effect is that kldloading the usb module
will panic the system in uhci_intr(). This added sanity check stops
this from happening: I can now kldload the usb.ko module without any
problems and load/attach other USB drivers after it.
Of course the uhci driver has no detach method, but that's another
problem.
- In uhci_run(), set the UHCI_CMD_MAXP bit in the command register to
allow 64-byte packets to be used for full speed bandwidth reclamation.
Certain high speed devices (in this case the ADMtek USB ethernet
adapter) require this bit to be set, otherwise babble errors occur
at the end of large (between 1100 and 1500 byte) transfers. This
should not affect other devices, although supposedly it is less efficient
than the 32-byte setting. Unfortunately, this is a per-bus setting,
not a per-device setting, so we can't just enable it for certain
devices on the USB bus.
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
Add support, kinda, for megaheartz xjack nic cards. This support
works well for one machine per ethernet segment because it hard codes
the MAC address. The pccardd in -current doesn't have support to
parse the ethernet address from the CIS in the funky way that the
megaheartz card does things (it includes it in the info tuple, as
ascii, which is non-standard). I'd rather kludge this for the moment
and work to read the CIS from the kernel rather than mess with
pccardd.
The isa attachment is untested. The pccard attachment is known to
work since I'm committing over it.
Card Obtained from: Chris D. Faulhaber <jedger@fxp.org>
now. On one machine with <825a> and <875> controllers, `sym' correctly
attached. On another one with only a <ncr 53c810 fast10 scsi>, the `ncr'
driver correctly attached.
- Don't keep private copies of some of the data fields from the
ENQUIRY and ENQUIRY2 commands. Instead, standardise on the ENQUIRY2
command for initial adapter information, and keep a copy of the entire
structure. Refer to it where appropriate.
- Move all of the controller description functionality into a new
function. Print lots more controller data if bootverbose is set.
Add knowledge of the DAC960 PR, PT, PTL0 and PRL controllers, rename
the 960PTL -> PTL0 and 1100P -> 1100PVX.
- Correctly terminate an error message.
The controller interface procedures have been reviewed against the
Mylex-supplied documentation; no changes appear necessary at this
time.
NFSSERVER defined, useful for userland fileservers that want to
use a filehandle type interface to the filesystem.
Submitted by: Assar Westerlund assar@stacken.kth.se
PR: kern/15452
