disconnected swap device.
This is quick and imperfect solution, as swap device will still be opened
and GEOM will not be able to destroy it. Proper solution would be to
automatically turn off and close disconnected swap device, but with existing
code it will cause panic if there is at least one page on device, even if
it is unimportant page of the user-level process. It needs some work.
Reviewed by: kib@
MFC after: 1 week
checking the returned oldlen: when ENOMEM is due to the supplied
buffer being too short the return oldlen is equal to buffer size.
Without this additional check sockstat gets stuck in loop leaking the
memory if the returned ENOMEM was due the exceeded memorylocked
limit. This is easily can be observed running `limits -l 1k sockstat'.
Submitted by: Andrey Zonov <andrey zonov org>
MFC after: 1 week
checking the returned oldlen: when ENOMEM is due to the supplied
buffer being too short the return oldlen is equal to buffer size.
Without this additional check kvm_getprocs() gets stuck in loop if the
returned ENOMEM was due the exceeded memorylocked limit. This is
easily can be observed running `limits -l 1k top'.
Submitted by: Andrey Zonov <andrey zonov org>
MFC after: 1 week
channels available
- current code treats bits 4:7 in 'SATAHC interrupt mask' and 'SATAHC
interrupt cause' as flags for SATA channels 2 and 3
- for embedded SATA controllers (SoC) these bits have been marked as reserved
in datasheets so far, but for some new and upcoming chips they are used for
purposes other than SATA
Submitted by: Lukasz Plachno
Reviewed by: mav
Obtained from: Semihalf
MFC after: 2 weeks
to cleanup routes from a single ifa.
o Implement carp_addroute()/carp_delroute() via above functions.
o Call carp_ifa_delroute() in the carp_detach() to avoid
junk routes left in routing table, in case if user
removes an address in a MASTER state. [1]
Reported by: az [1]
it is possible that a single AIO event will be reported to multiple
threads, it is not threading friendly, and the existing API can not
control this behavior.
Allocate a kevent flags field sigev_notify_kevent_flags for AIO event
notification in sigevent, and allow user to pass EV_CLEAR, EV_DISPATCH
or EV_ONESHOT to AIO kernel code, user can control whether the event
should be cleared once it is retrieved by a thread. This change should
be comptaible with existing application, because the field should have
already been zero-filled, and no additional action will be taken by
kernel.
PR: kern/156567
* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.
* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.
The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.
Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.
hardware imposes strict limitations on hard buffer and block sizes.
Previous code set soft buffer to be no smaller then hard buffer. On some
cards with fixed 64K physical buffer that caused up to 800ms play latency.
New code allows to set soft buffer size down to just two blocks of the hard
buffer and to not write more then that size ahead to the hardware buffer.
As result of that change I was able to reduce full practically measured
record-playback loop delay in those conditions down to only about 115ms
with theoretical playback latency of only about 50ms.
New code works fine for both vchans and direct cases. In both cases sound(4)
tries to follow hw.snd.latency_profile and hw.snd.latency values and
application-requested buffer and block sizes as much as limitation of two
hardware blocks allows.
Reviewed by: silence on multimedia@
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
Nextboot(8) can now set any combination of kernel name (-k), kernel
options (-o), and environment strings (-e). As a result of this change
-k also becomes optional.
Reviewed by: freebsd-current (Ian Lepore, pluknet@, jhb@)
any thread doing an I/O RPC with a transfer size greater than
NFS_UDPMAXDATA will be hung indefinitely, retrying the RPC.
After a discussion on freebsd-fs@, I decided to add a warning
message for this case, as suggested by Jeremy Chadwick.
Suggested by: freebsd at jdc.parodius.com (Jeremy Chadwick)
MFC after: 2 weeks
under the subject "F_RDLCK lock to FreeBSD NFS fails to R/O target file".
This occurred because the server side NLM always checked for VWRITE
access, irrespective of the type of lock request. This patch
replaces VOP_ACCESS(..VWRITE..) with one appropriate to
the lock operation. It allows unlock and lock cancellation
to be done without a check of VOP_ACCESS(), so that files
can't be left locked indefinitely after the file permissions
have been changed.
Discussed with: zack
Submitted by: jwd (earlier version)
Reviewed by: dfr
MFC after: 2 weeks
compliance testing.
In order to allow for radar pattern matching to occur, the DFS CAC/NOL
handling needs to be made configurable. This commit introduces a new
sysctl, "net.wlan.dfs_debug", which controls which DFS debug mode
net80211 is in.
* 0 = default, CSA/NOL handling as per normal.
* 1 = announce a CSA, but don't add the channel to the non-occupy list
(NOL.)
* 2 = disable both CSA and NOL - only print that a radar event occured.
This code is not compiled/enabled by default as it breaks regulatory
handling. A user must enable IEEE80211_DFS_DEBUG in their kernel
configuration file for this option to become available.
Obtained from: Atheros
* For legacy NICs, the combined RSSI should be used.
For earlier AR5416 NICs, use control chain 0 RSSI rather than combined
RSSI.
For AR5416 > version 2.1, use the combined RSSI again.
* Add in a missing AR5212 HAL method (get11nextbusy) which may be called
by radar code.
This serves no functional change for what's currently in FreeBSD.
about new child not only when doing PT_TO_SCX, but also for PT_CONTINUE.
If TDB_FORK flag is set, always issue a stop, the same as is done for
TDB_EXEC.
Reported by: Dmitry Mikulin <dmitrym juniper net>
MFC after: 1 week
that instead of using direct I/O it allows read-ahead similar to
POSIX_FADV_NORMAL, but invokes VOP_ADVISE(POSIX_FADV_DONTNEED) after the
read(2) has completed to purge just-read data. The write(2) path continues
to use direct I/O for POSIX_FADV_NOREUSE for now. Note that NOREUSE works
optimally if an application reads and writes full fs blocks.
that we have the lock now. This cleans up a locking panic ASSERT when
knlist_empty is called without a lock when INVARIANTS etc. are turned.
Reviewed by: kib jhb
MFC after: 1 week
This fixes the bug: when procstat -xa was run and the sysctl for a
process returned ESRCH or EPERM, for this process procstat output the
result collected for the previous successful process.
