clean up parts of the *_recv_mgmt() functions.
- make sure appropriate counters are bumped and debug messages are printed
- order the unhandled subtypes by value and add a few missing ones
- fix some whitespace nits
- remove duplicate code in adhoc_recv_mgmt()
- remove a useless comment, probably left in while c&p
The current code transmits management and multicast frames at MCS 0.
What it should do is check whether the negotiated basic set is zero (and
the MCS set is not) before making this decision.
For now, simply default to the lowest negotiated rate, rather than
MCS 0. This fixes the behaviour with at least the DLINK DIR-825, which
ACKs but silently ignores block-ack (BA) response frames.
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
o IEEE80211_IOC_CHANSWITCH fixups:
- restrict to hostap vaps
- return EOPNOTSUPP instead of EINVAL when applied to !hostap vap
or to a vap w/o 11h enabled
- interpret count of 0 to mean cancel the current CSA
Reviewed by: rpaulo, avatar
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
and xmit parameters. This makes it possible to use tdma on fractional
channels.
o add IEEE80211_MODE_HALF and IEEE80211_MODE_QUARTER; note these are
band-agnostic (may need revisiting)
o setup all default rates in ic_sup_rates instead of doing it only
for active modes; we need these to calculate the default tx parameters
which are not recalculated after a regulatory update (can't just
recalculate after installing a new channel list because we might
clobber user settings)
o remove special case code in ieee80211_get_suprates; this is now
a candidate for an inline or removal
o add various entries for new modes (roaming+tx params, wme, rate
mapping, scan set setup, country ie construction, tdma, basic rates)
Note these modes are intentionally not visible through if_media.
parent interface tasks to complete. This had been added to the ioctl path but
it is also need elsewhere like detach so its safe to teardown.
Reported by: Hans Petter Selasky
Submitted by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
don't do this right; instead go to the scan cache so we pass through
auth state (if the cache is warm we can do this w/o an actual scan)
MFC after: 1 week
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
through wpa_supplcant. If a sta is deauth'd (e.g. due to inactivity)
with roaming mode set to manual then a subsequent MLME assoc request
will be incorrectly handled and the station will never reauthenticate.
To fix this interpret a reason code of zero as sufficient to send an
auth request frame.
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
the state machine clocks to INIT, node references are not reclaimed.
Add a new routine ieee80211_drain_ifq that does this and use it
instead of IF_DRAIN.
Submitted by: Sepherosa Ziehau
Obtained from: DragonFly
MFC after: 1 month
o add IEEE80211_F_JOIN flag to ieee80211_fix_rate to indicate a station
is joining a BSS; this is used to control whether or not we over-write
the basic rate bit in the calculated rate set
o fix ieee80211_fix_rate to honor IEEE80211_F_DODEL when IEEE80211_F_DONEGO
is not specified (e.g. when joining an ibss network)
o on sta join always delete unusable rates from the negotiated rate set,
this was being done only ibss networks but is also needed for 11g bss
with mixed stations
o on sta join delete unusable rates from the bss node's rate set, not the
scan table entry's rate set
o when calculating a rate set for new neighbors in an ibss caculate a
negotiated rate set so drivers are not presented with rates they should
not use
Submitted by: Sepherosa Ziehau (w/ modifications)
Obtained from: DragonFly
MFC after: 1 month
in the Public Safety Band):
o add channel flags to identify half/quarter-rate operation
o add rate sets (need to check spec on 4Mb/s in 1/4 rate)
o add if_media definitions for new rates
o split net80211 channel setup out into ieee80211_chan_init
o fixup ieee80211_mhz2ieee and ieee80211_ieee2mhz to understand half/quarter
rate channels: note we temporarily use a nonstandard/hack numbering that
avoids overlap with 2.4G channels because we don't (yet) have enough
state to identify and/or map overlapping channel sets
o fixup ieee80211_ifmedia_init so it can be called post attach and will
recalculate the channel list and associated state; this enables changing
channel-related state like the regulatory domain after attach (will be
needed for 802.11d support too)
o add ieee80211_get_suprates to return a reference to the supported rate
set for a given channel
o add 3, 4.5, and 27 MB/s tx rates to rate <-> media conversion routines
o const-poison channel arg to ieee80211_chan2mode
particular this fixes use of wme in adhoc demo mode, it wasn't possible
to set the txop limit because the aggressive mode logic would override
Reviewed by: apatti
MFC after: 2 weeks
in the 802.11 layer: we send a directed probe request frame to the
current ap bmiss_max times (w/o answer) before scanning for a new ap.
MFC after: 2 weeks
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
