devices and the FreeBSD USB stack itself. This program can be used to
test compliance against well established usb.org standards, also
called chapter-9 tests. The host platform can act as either USB device
or USB host depending on the available hardware. The basic USB
communication happens through FreeBSD's own libusb v2, and some
sysctls are also used to invoke specific error conditions. This test
program can be used to verify correct operation of external USB
harddisks under heavy load and various other conditions. The software
is driven via a simple command line interface. Main supported USB host
classes are "USB mass storage" and "USB modems".
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: so (des)
Remove it if the knob isn't tweaked. Certain ports seem to think that
if /usr/bin/iconv exists, then libc has built in libiconv things and will
blow up pretty nicely when built.
Reviewed by: gjb@
MFC after: 2 weeks
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and
for general purpose monitoring without tapping any cxgbe or cxl ifnet
directly.
Tracers on the T4/T5 chips provide access to Ethernet frames exactly as
they were received from or transmitted on the wire. On transmit, a
tracer will capture a frame after TSO segmentation, hw VLAN tag
insertion, hw L3 & L4 checksum insertion, etc. It will also capture
frames generated by the TCP offload engine (TOE traffic is normally
invisible to the kernel). On receive, a tracer will capture a frame
before hw VLAN extraction, runt filtering, other badness filtering,
before the steering/drop/L2-rewrite filters or the TOE have had a go at
it, and of course before sw LRO in the driver.
There are 4 tracers on a chip. A tracer can trace only in one direction
(tx or rx). For now cxgbetool will set up tracers to capture the first
128B of every transmitted or received frame on a given port. This is a
small subset of what the hardware can do. A pseudo ifnet with the same
name as the nexus driver (t4nex0 or t5nex0) will be created for tracing.
The data delivered to this ifnet is an additional copy made inside the
chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual.
/* watch cxl0, which is the first port hanging off t5nex0. */
# cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting)
# cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving)
# cxgbetool t5nex0 tracer list
# tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire
If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K
"frames" with no L3/L4 checksum but this will show you the frames that
were actually transmitted.
/* all done */
# cxgbetool t5nex0 tracer 0 disable
# cxgbetool t5nex0 tracer 1 disable
# cxgbetool t5nex0 tracer list
# ifconfig t5nex0 destroy
The BSD-licensed patch(1) command has matured and it's behaviour
can be considered equivalent to the older version of GNU patch
in the tree.
The switch has been extensively tested [1] and only two ports
presented regressions, which have since been fixed.
For convenience a new WITH_GNU_PATCH option is available,
but it will likely be removed in the near future.
PR: 176313
Approved by: portmgr
make the ARM EABI the default ABI on arm, armeb, armv6 and armv6eb.
This is intended to be the default ABI from now on with the old ABI to be
retired. Because of this all users are strongly suggested to upgrade to the
ARM EABI.
As the two ABIs are incompatible it is unlikely upgrading in place will
work. Users should perform a full backup and either use an external machine
to upgrade, or install to an alternative location on their media. They
should also reinstall all ports or packages when these are available.
The only known issues are:
- pkg incorrectly detects the ABI. This is fixed upstream, and will a
patch will be made to the port.
- GDB can have issues with executables built with clang.
__FreeBSD_version has been bumped.
Although using -i with -c does not seem very useful, it seems inappropriate
to read commands from the terminal in this case.
Side effect: if the -s -c extension is used and the -s option is turned off
using 'set +s' during the interactive part, the shell now exits after an
error or interrupt. Note that POSIX only specifies -s as option to sh, not
to set.
See also Austin Group issue #718.
- spa status can not be called before spa init
- libzfs.h inclusion is now required
- fix alternative code for explicit root dataset lookup
MFC after: 10 days
This is a workaround for WITH_LDNS_UTILS forcing BIND_UTILS off. It can
be reverted when we no longer have these conflicting options, or made more
general if we grow more cases like this.
