- doesn't break my system.
- NOT yet verified on the affected motherboard.
Stifle an annoying dma_start busy message for the sound cards.
Submitted by: "John S. Dyson" <toor@dyson.iquest.net>
simplifies some assumptions and stops some code compile problems.
This should fix the compile hiccup in PR#3491, but smp kernel profiling
isn't likely to be fixed by this.
Peter Wemm <peter@spinner.DIALix.COM>, Steve Passe <smp@csn.net>
removed all the IPI_INTS code.
made the XFAST_IPI32 code default, renaming Xfastipi32 to Xinvltlb.
cleanup of i386/isa/isa_device.h to eliminate SMP dependancies:
made the id_irq member of struct isa_device an u_int.
made the id_drq member of struct isa_device an int.
removed all other '#ifdefs' concerning SMP & APIC_IO.
removed SMP/APIC_IO dependancies from if_ze.c.
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
have successfully built, booted, and run a number of different ELF
kernel configurations, including GENERIC. LINT also builds and
links cleanly, though I have not tried to boot it.
The impact on developers is virtually nil, except for two things.
All linker sets that might possibly be present in the kernel must be
listed in "sys/i386/i386/setdefs.h". And all C symbols that are
also referenced from assembly language code must be listed in
"sys/i386/include/asnames.h". It so happens that failure to do
these things will have no impact on the a.out kernel. But it will
break the build of the ELF kernel.
The ELF bootloader works, but it is not ready to commit quite yet.
print "at <not configured>" for iobase == -1 (autodetect not happens)
and not print anything for iobase == -2 (none)
Old code treat this two special config numbers as big port numbers.
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
is still broken - it doesn't restore the floating point state.
2.2-BETA users should disable it using npx0 flags 0x04 the same as
2.2-ALPHA users should have.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
handlers if interrupts are nested more than a few (3) deep. This
only reduces the maximum nesting level by 1 with the standard
drivers unless there is a related bug somewhere, but can't hurt
much (the worst case is returning to hoggish interrupt handler like
wdintr(), but such interrupt handlers hurt anyway).
Fixed a previously harmless race incrementing the interrupt nesting
level.
This should be in 2.1.6 and 2.2.
hardware interrupt counts add up to the total. Previously, software
interrupts generated by splz() were counted in the total. These
software interrupts seem to be very rare - there have apparently been
0 of them on freefall among the last 352448857 interrupts.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
