cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
variable `kern.maxvnodes' which gives much better control over vnode
allocation than EXTRAVNODES (except in -current between 1995/10/28 and
1996/11/12, kern.maxvnodes was read-only and thus useless).
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
when allocating memory for network buffers at interrupt time. This is due
to inadequate checking for the new mcl_map. Fixed by merging mb_map and
mcl_map into a single mb_map.
Reviewed by: wollman
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
previous hackery involving struct in_ifaddr and arpcom. Get rid of the
abominable multi_kludge. Update all network interfaces to use the
new machanism. Distressingly few Ethernet drivers program the multicast
filter properly (assuming the hardware has one, which it usually does).
compile again. The code to protect users from combining the dedicated
PCCARD drivers and the generic code is a warning if the above option
is included in the config file.
Demanded by: bde
(helptext from Philippe Regnauld)
- Make introfunc() work with serial terminals.
(submitted by Jean-Marc Zucconi)
- Eliminate excessive statusline redraw during screen updates.
(requested by Peter Wemm)
- Some trivial output formatting dinks.
> <sys/param.h> doesn't include <sys/time.h>
>
> I removed the NAPM check since it's wasteful to check twice. apmprobe()
> checks the unit number, and that's the right check.
Submitted by: bde
swapgeneric.c hasn't had anything to do with swapping for some time.
It just makes the -a boot option actually work, and breaks the static
configuration of rootdev and dumpdev. It should be reorganized to
only support -a.
etc..), plus add a better display suspend function.
- Changed the Copyright's to reflect the new 'jp.FreeBSD.org' email
address.
Submitted by: nate & HOSOKAWA, Tatsumi <hosokawa@jp.FreeBSD.org>
- the operands for bt, bts, arpl and `enter' were reversed.
- btr was reported as bts (with the correct operand order).
- cmpxchg was misplaced. It was misplaced differently in the
comments. It is misplaced differently again in the i486 manual.
I put it where the i586 manual and gas say it is.
- fucompp was misplaced.
- the rr table for(s) some versions of fstp, fcom and fcomp was non-null.
This caused some invalid opcodes to be reported as "" instead of as
"<bad instruction>".
- the word and long versions of the fi* instructions were reversed.
- aaa and daa were reversed.
Fixed bugs involving unusual operand sizes:
- 32-bit registers weren't always forced for bswap or for moves to and
from special registers.
- the operand sizes weren't reported for [l]call or [l]jmp.
- displacements weren't truncated mod 2^16 when the operand size was
16-bit.
- too-large displacements and offsets were fetched, and too-large
offsets were reported, when the operand size was 16-bit.
- sign extended immediate bytes were extended too far when the operand
size was 16-bit.
Fixed bugs involving usual operand sizes:
- 8-bit source registers weren't forced for mov[sz]b[wl].
- 16-bit source registers weren't forced for mov[sz]w[wl].
- immediate bytes were sometimes reported as sign extended even for
byte operations. Same for immediate words in word operations.
- the immediate byte was not reported as sign extended for `push'.
Finished Pentium support:
- cpuid, cmpxchg8b and rsm were missing.
Finished i287 support:
- fneni, fndisi and fsetpm were missing. These are harmless nops on
later FPUs.
Improvements:
- report invalid opcodes 0xd6 and 0xf1 using .byte. They are special
in not causing invalid operand exceptions when executed.
- report the immediate byte for unusual aam and aad instuctions.
Immediate bytes other than 0x0a always worked and are documented to
work on Pentiums.
wdparams from short into u_short. If wdp_cylinders is short, it
overflows and cause serious sign extension bug when large IDE HDD is
used. These members are only used for initialization of u_long
variables in both 3.0-current and RELENG_2_2 branch.
I believe this should be in 2.2.
Reviewed by: Bruce Evans <bde@zeta.org.au>
This code was sent to me by Bruce Evans, and seems to fix some
possible kernel panic in case of an execution error. It did not
cause any problems on my system, but I did never observe the
problem this patch is supposed to fix, anyway.
This patch is a NOP, unless the kernel is built with "options
USER_LDT", and doesn't affect the GENERIC kernel for this reason.
I want to have it in 2.2: it fixes a bug ...
Submitted by: bde
taken from the voxware-3.5 distribution. Also some changes to the SB
and MPU IRQs to reflect more common/default settings.
Submitted-By: Brian Campbell <brianc@netrover.com>
at device attach time, instead of allocating and freeing buffers as
necessary. But he or she forgot to remove the line that invalidated
the buffer when the device is closed. Therefore, after using the
device for the first time, the buffer was incorrectly invalidated and
that caused a page fault on the second, and subsequent uses.
Closes PR # kern/2319: Using Genius GS-4500 scanner...
Submitted by: jmrueda@diatel.upm.es (Javier Martmn Rueda)
also implies VM_PROT_EXEC. We support it that way for now,
since the break system call by default gives VM_PROT_ALL. Now
we have a better chance of coalesing map entries when mixing
mmap/break type operations. This was contributing to excessive
numbers of map entries on the modula-3 runtime system. The
problem is still not "solved", but the situation makes more
sense.
Eventually, when we work on architectures where VM_PROT_READ
is orthogonal to VM_PROT_EXEC, we will have to visit this
issue carefully (esp. regarding security issues.)
is still broken - it doesn't restore the floating point state.
2.2-BETA users should disable it using npx0 flags 0x04 the same as
2.2-ALPHA users should have.
Closes PR # kern/1065.
While i was at it, also reject IO requests that are not an integer
multiple of the device blocksize.
Submitted by: vak@crox.net.kiae.su (Serge V.Vakulenko)
Confirmed by: Georg-W. Koltermann (gwk@cray.com)
workings of #error in particular. He also broke the 2.2 build with this
change, leading me to wonder whether or not the changes were ever even
tested. Folks, I'm happy to see people work directly on 2.2 like
this and will continue to encourage Nate to make direct commits, but
please TEST before committing! I think that's a more than reasonable
prerequisite, and this code could never have worked at all, leading me to
believe that Nate skipped this most basic of steps.
Don't allow people to use the 'dedicated' drivers at the same time as
the generic support code, as it can cause all sorts of problems
including kernel crashes.
[ definite 2.2 material ]
Broke locking on named pipes in the same way as locking on non-vnodes
(wrong errno). This will be fixed later.
The fix involves negative logic. Named pipes are now distinguished from
other types of files with vnodes, and there is additional code to handle
vnodes and named pipes in the same way only where that makes sense (not
for lseek, locking or TIOCSCTTY).
This makes unexpected faults (in an interrupt handler) more likely
to crash properly. It could be done even better (more robustly and
more efficiently) using lazy fault handling.
They were garbage that happened to be 0 in many cases. (real_to_prot()
happens to leave the value of the real-mode %cr0 in %eax and the
memory-size BIOS calls usually don't touch the upper bits of %eax.
The upper 16 bits of %cr0 are usually 0 at boot time, at least on
486's.
Should be in 2.2.
configure() where it always belonged. It was originally slightly
misplaced after configure(). Rev.138 left it completely misplaced
before the DEVFS, DRIVERS and CONFIGURE sysinits by not moving it
together with configure().
Restored the printing of bootinfo.bi_n_bios_used now that it can
be nonzero.
EISA slots to probe. This is mainly intended to allow installing the
system on an HP Netserver with an on-board AIC7xxx EISA SCSI
controller, that is sitting on EISA slot # 11.
Documentation updates explaining this hack will follow shortly.
Note that this can go away again as soon as the EISA device probing
is more intelligent about the address space clash with the PCI address
space.
2.2 candidate.
Not objected by: freebsd-core :)
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
the profiling level in config and decide what to do in makefiles.
Makefile.i386:
Align functions to 16-byte boundaries if profiling is enabled. This
will allow a fourfold reduction in the size of the profiling buffers.
I've added an installation from optical disk drive facility.
This enables FreeBSD to be installed from an optical disk, which
may be formatted in "super floppy" style or sliced into MSDOS-FS
and UFS partitions.
Note: ncr.c should be reviewed by Stefan Esser <se@freebsd.org>
and cd.c by Joerg Wunsch <joerg@freebsd.org> before bringing this
into 2.2.
Submitted-By: Shunsuke Akiyama <akiyama@kme.mei.co.jp>
makerom checksum check calculation was a no-op
nb8390.c had a bug which caused packet_len to be incorrect
for packets which wrapped in the buffer.
Submitted by: Linux developers (I lost the email with their names)
partition is 0, which is outside the slice unless the disk is
dangerously dedicated. There is little error checking later, and
following garbage metadata outside the slice usually caused crashes,
Empty 'a' partitions are fairly easy to create by cloning the label
for the whole disk.
Fixed a missing newline in a related error message.
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
ACTUALLY_LKM_NOT_KERNEL until the real fix comes through. Whatever
flag that is used to indicate building LKMs will have be be substituted
in the future. This allows proper selection of the usage of the
efficient, single instruction in the kernel, but alas, doesn't allow
for use in userland or LKMs :-(. Them's the breaks!!!
with one of the following (I486_CPU,I586_CPU,I686_CPU) so it can take
advantage of the very quick bswap insn. This keeps LKMs from being
built to take advantage of the insn, but also makes sure that the LKMs
can be run on all CPUs. (The LKMs don't pick up the CPU options :-( ).
function ed_attach_NE2000_pci() in if_ed.c passes
an uninitialized block of memory (got with malloc())
to ed_attach. This prevents a proper initialization
of the device descriptor and in my case causes a panic
during the probe, while printing out device info.
Reviewed by: phk
Submitted by: Luigi Rizzo <luigi@iet.unipi.it>
list of IP setsockopts the Linux emulator recognizes.
Explicitly disallow IP_HDRINCL since Linux's handling of
raw output is different than BSD's.
Closes PR#kern/2111.
Submitted by: y-nakaga@ccs.mt.nec.co.jp (Yoshihisa NAKAGAWA)
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
decrease the size of buffer_map to approx 2/3 of what it used to be
(buffer_map can be smaller now.) The original commit of these changes
increased the size of buffer_map to the point where the system would
not boot on large systems -- now large systems with large caches will
have even less problems than before.
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
registers.) Also clean up some namespace pollution, and remove
gcc-1 support (nothing really works with it anymore anyway.)
Submitted by: Bruce Evans <bde@freebsd.org> and me.
consistent stack frame in fastmove() so that only one new fault handler
is necessary.
Should be in 2.2. Harmless until the i586 versions are reenabled.
Per Wayne Scott of Intel, the old sequence took 20cycles!!! on a P6.
Another nice side-benefit is that the kernel is about 3K smaller!!!
Submitted by: Wayne Scott <wscott@ichips.intel.com>
the keyboard IO port definitions from <machine/console.h>.
Note: I do not have a machine available to test this yet, I sent this
for review to several people who have not replied.
This is also totally busted in 2.2, which has half of the syscons/psm/kbdio
changes in it. This really desperately needs to be tested and fixed
in 2.2 as well.
SCBs in response to a busfree.
When re-queueing an SCB that returned with QUEUE FULL status, reset its timeout.
Ensure that aborted SCBs have an error code set in there xs before it gets
passed back up with scsi_done.
Fix a few KNF nits.
uses /usr/include/sys/*, which may point to a different build tree. I'm
not sure that this is necessary, but there was a question mark over what
/usr/include/sys points to when building the "user mode" binaries in the
kernel code, especially when building the smp tree.
I suspect that the "right" line here is to use ${INCLUDES}, but that
causes warnings about unused static inline functions in stdio.h and ctype.h
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
substantially increasing buffer space. Specifically, we double
the number of buffers, but allocate only half the amount of memory
per buffer. Note that VDIR files aren't cached unless instantiated
in a buffer. This will significantly improve caching.
do reset it from the QOUTCNT register inside a pause/unpause. This now happens
once per command complete interrupt in the paging case (one interrupt can be
for multiple completed commands). I may introduce a counter and do a lazy
update in the future, similar to what is done with the QINCNT.
Enhance the QUEUE FULL condition handling so that the number of openings will
be reduced. This has become more important now that the driver is faster.
This code really belongs in the gerneric SCSI layer, as will be the case once
3.0 gets the code from the 'SCSI' branch.
Add some #if 0'd out trace code I've been using to help debug sequencer
problems.
Fix the SCB paging problem that I was seeing. This was only on my 7850
controller and stems from the fact that its QINFIFO can only handle 3bit
SCB identifiers. This means that you can only have 8 transactions open at
a time with the current paging scheme to these controllers. The code added
to enforce this is generic in that it tests for the number of relevent bits
that the QINFIFO can store and adjusts the max accordingly. It may be possible
to come up with a scheme that allows for more than 8 commands at a time, but
I don't know that it is worth the effort simply to fix a low end card. The
aic7880 still can do 255.
This problem may be related to what Andrey was seeing since I don't have n
aic7770 rev E chip here to test on, but as soon as someone probes one of these
cards with this new code, the dmesg output will tell the whole story.
aic7xxx cards failing on certain motherboards, reverse the logic used to
control this feature. AHC_FORCE_PIO is replaced with AHC_ALLOW_MEMIO.
GENERIC no longer needs to specify the AHC_FORCE_PIO option since this is
the default.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
with the copyright stuff fixed so soon (this should be merged into 2.2 when
you have a chance, Poul).
This is the new AWE32 driver, with support for the AWE32's fancy MIDI
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
