Have pmcstat(8) and pmccontrol(8) use these APIs.
Return PMC class-related constants (PMC widths and capabilities)
with the OP GETCPUINFO call leaving OP PMCINFO to return only the
dynamic information associated with a PMC (i.e., whether enabled,
owner pid, reload count etc.).
Allow pmc_read() (i.e., OPS PMCRW) on active self-attached PMCs to
get upto-date values from hardware since we can guarantee that the
hardware is running the correct PMC at the time of the call.
Bug fixes:
- (x86 class processors) Fix a bug that prevented an RDPMC
instruction from being recognized as permitted till after the
attached process had context switched out and back in again after
a pmc_start() call.
Tighten the rules for using RDPMC class instructions: a GETMSR
OP is now allowed only after an OP ATTACH has been done by the
PMC's owner to itself. OP GETMSR is not allowed for PMCs that
track descendants, for PMCs attached to processes other than
their owner processes.
- (P4/HTT processors only) Fix a bug that caused the MI and MD
layers to get out of sync. Add a new MD operation 'get_config()'
as part of this fix.
- Allow multiple system-mode PMCs at the same row-index but on
different CPUs to be allocated.
- Reject allocation of an administratively disabled PMC.
Misc. code cleanups and refactoring. Improve a few comments.
theoretically unload pci bridges or pci drivers. It will also allow
detach to work if one needed to detach a subtree.
This is inspired by looking at the p4 commits from bms to his 5.4
tree, but I didn't look at the final results.
for the VGA I/O or memory ranges, when it's not within the default
ranges decoded by the bridge. When allocation for VGA addresses is
attempted, check that the bridge has the VGA Enable bit set before
allowing it.
As such, newbusified VGA drivers can allocate their resources when
the VGA adapter is behind a PCI-to-PCI bridge.
Reviewed by: imp@, jhb@
Only allow a process to use the x86 RDPMC instruction if it has
allocated and attached a PMC to itself.
Inform the MD layer of the "pseudo context switch out" that needs
to be done when the last thread of a process is exiting.
fact that access to RR0 does not need a prior write to the register
index because the index always reverts to 0 after the indexed register
has been accessed.
Typically when a RR or WR is to accessed, one programs the index (which
is a write to the control register), followed by a read or write to the
actual indexed register (a read pr write to the same control register).
When this non-atomic sequence is interrupted after having written the
index and low-level console I/O is done in that situation, the write to
program the index will actually write to the indexed register and nuke
state. This almost always yields a wedge.
By not programming the index register and instead just reading from RR0,
the worst case scenario is non-fatal. For if we don't actually read from
RR0 but some other register we get an invalid status, which may lead us
to conclude that the transit data register is empty when it's not or that
the receive data register contains data when it doesn't. Hence, we may
lose an output character or get a sporadic input character, but given
the situation this is a non-issue.
Full serialization is not possible due to the fact that this code needs
to work from DDB and before mutex initialization has happened.
In collaboration with: kris@, marius@
Tested by: kris@
MFC after: 1 day
X-MFC: 5.4-RELEASE candidate
during a data phase. Before, we would try to recover the autosense, but
the DMA engine would still be active with interrupted transfer, and we'd
quickly spiral out of control and cause massive data corruption. For now,
just reset the chip and cancel everything. The better solution is to
cancel the DMA operation, but there is no clear way to do that right now.
The data corruption problem is severe enough to warrant this fix in the
interim. Thanks to Kris Kenneway to sacrificing countless filesystems to
this bug.
MFC After: 3 days
on boards with VIA gigE controllers that are embedded in VIA chipsets.
Presumably, they don't have an external EEPROM and store the MAC
address somewhere else. To get around this, force an autoload and
read the station address from the RX filter registers instead.
This has been tested to work on both embedded and standalone
controllers.
While there also check for failed device_add_child calls.
Found by: Coventry Analysis tool[1].
Submitted by: sam[1]
Approved by: pjd (mentor)
MFC after: 1 week
here on in, if_ndis.ko will be pre-built as a module, and can be built
into a static kernel (though it's not part of GENERIC). Drivers are
created using the new ndisgen(8) script, which uses ndiscvt(8) under
the covers, along with a few other tools. The result is a driver module
that can be kldloaded into the kernel.
A driver with foo.inf and foo.sys files will be converted into
foo_sys.ko (and foo_sys.o, for those who want/need to make static
kernels). This module contains all of the necessary info from the
.INF file and the driver binary image, converted into an ELF module.
You can kldload this module (or add it to /boot/loader.conf) to have
it loaded automatically. Any required firmware files can be bundled
into the module as well (or converted/loaded separately).
Also, add a workaround for a problem in NdisMSleep(). During system
bootstrap (cold == 1), msleep() always returns 0 without actually
sleeping. The Intel 2200BG driver uses NdisMSleep() to wait for
the NIC's firmware to come to life, and fails to load if NdisMSleep()
doesn't actually delay. As a workaround, if msleep() (and hence
ndis_thsuspend()) returns 0, use a hard DELAY() to sleep instead).
This is not really the right thing to do, but we can't really do much
else. At the very least, this makes the Intel driver happy.
There are probably other drivers that fail in this way during bootstrap.
Unfortunately, the only workaround for those is to avoid pre-loading
them and kldload them once the system is running instead.
16C950. Adding it here doesn't unlock any of the cool 16C950 features
(like the 128 byte fifo, the different prescalor, etc), but it does
seem to get it working for me in light testing.
Card Provided by: Ihsan Dogan
pumping data despite our scsi data counters being at 0, something has
gone massively wrong. The consequence of happily ignoring this is more
DMA phase errors and a disk full of spammed sectors. Instead, panic on
the first occurance to hopefully limit the damage.
MFC After: 3 days
latest 82550 and 82551 chipsets (revision IDs 0x0e, 0x0f and 0x10).
We were only enabling it for revisions 0x0c and 0x0d, now it's
enabled for any 8255x NIC with a revision ID bigger than 0x0c. It
should be safe, and this is what Intel does in their open source
driver.
MFC after: 2 weeks
Tested by: Pavel Lobach lobach_pavel at mail dot ru
This also removes the warning timeout on the taskqueues stalling as
I'm tired of getting ATA error reports for problems in other parts ;)
Misc cosmetic and comment cleanups now we are here.
number of task threads to start on boot. Go back to a default of 3
threads to work around lost battery state problems. Users that need
a setting of 1 can set this via the tunable. I am investigating the
underlying issues and this tunable can be removed once they are solved.
MFC after: 2 days
includes the MD header for us. Do not include <machine/specialreg.h>
as it is not a header file that can be included from MI files. It
is included from <machine/pmc_mdep.h> if so needed and possible.
Ok'd: jkoshy@
ioctls are now handled explicitly, but we can't really do anything
with them unless the NIC is up (trying to get/set a parameter when
the NDIS driver isn't running always yields an error). If something
invokes either of these ioctls and the NIC isn't initialized, punt
to the default ieee80211_ioctl() routine.
