This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
Insted of embedding a struct g_stat in consumers and providers, merely
include a pointer.
Remove a couple of <sys/time.h> includes now unneeded.
Add a special allocator for struct g_stat. This allocator will allocate
entire pages and hand out g_stat functions from there. The "id" field
indicates free/used status.
Add "/dev/geom.stats" device driver whic exports the pages from the
allocator to userland with mmap(2) in read-only mode.
This mmap(2) interface should be considered a non-public interface and
the functions in libgeom (not yet committed) should be used to access
the statistics data.
included in the kernel. Include imgact_elf.c in conf/files, instead of
both imgact_elf32.c and imgact_elf64.c, which will use the default word
size for an architecture as defined in machine/elf.h. Architectures that
wish to build an additional image activator for an alternate word size can
include either imgact_elf32.c or imgact_elf64.c in files.${ARCH}, which
allows it to be dependent on MD options instead of solely on architecture.
Glanced at by: peter
With a 1 byte transmit fifo, 3 byte receive fifo, and wierd multiplexed I/O
designed for a Z80 cpu, this chip redefines suckage.
Based on the openbsd and netbsd drivers. Only really works as a console,
modem support is not complete since I can't test it.
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
Previously these were libc functions but were requested to
be made into system calls for atomicity and to coalesce what
might be two entrances into the kernel (signal mask setting
and floating point trap) into one.
A few style nits and comments from bde are also included.
Tested on alpha by: gallatin
No functional changes, but:
+ the mrouting module now should behave the same as the compiled-in
version (it did not before, some of the rsvp code was not loaded
properly);
+ netinet/ip_mroute.c is now truly optional;
+ removed some redundant/unused code;
+ changed many instances of '0' to NULL and INADDR_ANY as appropriate;
+ removed several static variables to make the code more SMP-friendly;
+ fixed some minor bugs in the mrouting code (mostly, incorrect return
values from functions).
This commit is also a prerequisite to the addition of support for PIM,
which i would like to put in before DP2 (it does not change any of
the existing APIs, anyways).
Note, in the process we found out that some device drivers fail to
properly handle changes in IFF_ALLMULTI, leading to interesting
behaviour when a multicast router is started. This bug is not
corrected by this commit, and will be fixed with a separate commit.
Detailed changes:
--------------------
netinet/ip_mroute.c all the above.
conf/files make ip_mroute.c optional
net/route.c fix mrt_ioctl hook
netinet/ip_input.c fix ip_mforward hook, move rsvp_input() here
together with other rsvp code, and a couple
of indentation fixes.
netinet/ip_output.c fix ip_mforward and ip_mcast_src hooks
netinet/ip_var.h rsvp function hooks
netinet/raw_ip.c hooks for mrouting and rsvp functions, plus
interface cleanup.
netinet/ip_mroute.h remove an unused and optional field from a struct
Most of the code is from Pavlin Radoslavov and the XORP project
Reviewed by: sam
MFC after: 1 week
"refreshing" the label on the vnode before use, just get the label
right from inception. For single-label file systems, set the label
in the generic VFS getnewvnode() code; for multi-label file systems,
leave the labeling up to the file system. With UFS1/2, this means
reading the extended attribute during vfs_vget() as the inode is
pulled off disk, rather than hitting the extended attributes
frequently during operations later, improving performance. This
also corrects sematics for shared vnode locks, which were not
previously present in the system. This chances the cache
coherrency properties WRT out-of-band access to label data, but in
an acceptable form. With UFS1, there is a small race condition
during automatic extended attribute start -- this is not present
with UFS2, and occurs because EAs aren't available at vnode
inception. We'll introduce a work around for this shortly.
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
they may be statically linked into the kernel. Note that statically
linked modules, unlike dynamically linked modules, get INVARIANTS,
so if there are INVARIANTS failures, you'll bump into them rather
than not. Add the options to NOTES.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
This is an encryption module designed for to secure denial of access
to the contents of "cold disks" with or without destruction activation.
Major features:
* Based on AES, MD5 and ARC4 algorithms.
* Four cryptographic barriers:
1) Pass-phrase encrypts the master key.
2) Pass-phrase + Lock data locates master key.
3) 128 bit key derived from 2048 bit master key protects sector key.
3) 128 bit random single-use sector keys protect data payload.
* Up to four different changeable pass-phrases.
* Blackening feature for provable destruction of master key material.
* Isotropic disk contents offers no information about sector contents.
* Configurable destination sector range allows steganographic deployment.
This commit adds the kernel part, separate commits will follow for the
userland utility and documentation.
This software was developed for the FreeBSD Project by Poul-Henning Kamp and
NAI Labs, the Security Research Division of Network Associates, Inc. under
DARPA/SPAWAR contract N66001-01-C-8035 ("CBOSS"), as part of the DARPA CHATS
research program.
Many thanks to Robert Watson, CBOSS Principal Investigator for making this
possible.
Sponsored by: DARPA & NAI Labs.
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
configuration stuff as well as conditional code in the IPv4 and IPv6
areas. Everything is conditional on FAST_IPSEC which is mutually
exclusive with IPSEC (KAME IPsec implmentation).
As noted previously, don't use FAST_IPSEC with INET6 at the moment.
Reviewed by: KAME, rwatson
Approved by: silence
Supported by: Vernier Networks
- Begin moving scheduler specific functionality into sched_4bsd.c
- Replace direct manipulation of scheduler data with hooks provided by the
new api.
- Remove KSE specific state modifications and single runq assumptions from
kern_switch.c
Reviewed by: -arch
allow us to avoid nasty by-hand string parsing stuff in a number of
places in the kernel, reducing the risk of unexpected consequences
for kernel correctness.
among other things, the DEVFS rule subsystem to match nodes against a
path pattern supplied by the user.
fnmatch.c was repo-copied from src/lib/libc/gen/fnmatch.c, and the
only changes to it are those necessary to make it compile in the
kernel. The relevant parts of fnmatch.h were imported into libkern.h.
Approved by: -arch
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
This allocate the best IRQ to boot-disable devices (have IRQ 0).
Allocated IRQ will be used for PCI interrupt routing when ACPI is
enabled.
Note that verbose messaging enabled for the time being so that
people can easily notice the strange behavior if it happened.
gets signals operating based on a TailQ, and is good enough to run X11,
GNOME, and do job control. There are some intricate parts which could be
more refined to match the sigset_t versions, but those require further
evaluation of directions in which our signal system can expand and contract
to fit our needs.
After this has been in the tree for a while, I will make in kernel API
changes, most notably to trapsignal(9) and sendsig(9), to use ksiginfo
more robustly, such that we can actually pass information with our
(queued) signals to the userland. That will also result in using a
struct ksiginfo pointer, rather than a signal number, in a lot of
kern_sig.c, to refer to an individual pending signal queue member, but
right now there is no defined behaviour for such.
CODAFS is unfinished in this regard because the logic is unclear in
some places.
Sponsored by: New Gold Technology
Reviewed by: bde, tjr, jake [an older version, logic similar]
aac driver dependent on the linux emulation module. This was
especially bad for the release engineers who tried to move the
aac driver from the kernel onto the drivers floppy. The linux
compat bits for this driver are now in their own driver, aac_linux.
It can be loaded as a module or compiled into the kernel. For
the latter case, the AAC_COMPAT_LINUX option is needed, along with
the COMPAT_LINUX option.
I've tested this in every configuration I can think of. This is an
MFC candidate for 4.7.
Idea from: rwatson
MFC after: 3 days
so that it is MI. Allow nfs_mountroot to return an error if the nfs_diskless
struct is not valid, rather than panicing later on. Call nfs_setup_diskless()
from nfs_mountroot if NFS_ROOT is defined, like bootpc_init(). Removed legacy
root mount support for sparc64, and enabled NFS_ROOT by default.
i4bq931, i4b, isic, iwic, ifpi, ifpi2, ifpnp, ihfc, and itjc are
no longer count devices. Also remove a few other instances of N<DEVICE>
being used to control compilation of whole files.
Reviewed by: hm
This feature can be disabled via the AHD/AHC_REG_PRETTY_PRINT kernel
option.
The ahc driver now uses the same debug options mechanism as ahd:
AHC_DEBUG - Compile in debugging code
AHC_DEBUG_OPTS - String of debug options as listed in aic7xxx.h
This is an architecture that present a thing message passing interface
to the OS. You can query as to how many ports and what kind are attached
and enable them and so on.
A less grand view is that this is just another way to package SCSI (SPI or
FC) and FC-IP into a one-driver interface set.
This driver support the following hardware:
LSI FC909: Single channel, 1Gbps, Fibre Channel (FC-SCSI only)
LSI FC929: Dual Channel, 1-2Gbps, Fibre Channel (FC-SCSI only)
LSI 53c1020: Single Channel, Ultra4 (320M) (Untested)
LSI 53c1030: Dual Channel, Ultra4 (320M)
Currently it's in fair shape, but expect a lot of changes over the
next few weeks as it stabilizes.
Credits:
The driver is mostly from some folks from Jeff Roberson's company- I've
been slowly migrating it to broader support that I it came to me as.
The hardware used in developing support came from:
FC909: LSI-Logic, Advansys (now Connetix)
FC929: LSI-Logic
53c1030: Antares Microsystems (they make a very fine board!)
MFC after: 3 weeks
The CAM<>ATAPI layer was submitted by "Thomas Quinot <thomas@cuivre.fr.eu.org>"
changes form the version on the net by me (formatting, ability to be used
alone without the ATAPI native device driver, proper speed reporting...)
See /sys/conf/NOTES for usage.
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
kernel access control.
Modify procfs so that (when mounted multilabel) it exports process MAC
labels as the vnode labels of procfs vnodes associated with processes.
Approved by: des
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
This driver actually works slightly better on -stable than on -current
(the system locks on detach on -current), so it should be MFC'd somewhat
sooner.
This driver currently points out a difficulty in the sound device framework.
The PCM unregister routine is allowed to refuse the detach if the device is
in use. In the case of a USB device, however, this unregistration is much more
mandatory in nature, since the device is *actually* gone when this call is
made. The sound subsystem really should not refuse an unregistration and
should take its own steps to reject further I/O. As a result, if you detach
a USB sound device while it is in use, you can expect a panic shortly
thereafter.
This device cannot currently record audio. Some routines are unwritten as
of yet in uaudio.c to support recording.
This device hangs my -current box on detach. I don't know why. This does
not happen on my -stable machine.
Obtained from: Hiroyuki Aizu
MFC after: 2 weeks
handler in the kernel at the same time. Also, allow for the
exec_new_vmspace() code to build a different sized vmspace depending on
the executable environment. This is a big help for execing i386 binaries
on ia64. The ELF exec code grows the ability to map partial pages when
there is a page size difference, eg: emulating 4K pages on 8K or 16K
hardware pages.
Flesh out the i386 emulation support for ia64. At this point, the only
binary that I know of that fails is cvsup, because the cvsup runtime
tries to execute code in pages not marked executable.
Obtained from: dfr (mostly, many tweaks from me).
administrator to define certain properties of new devfs nodes before
they become visible to the userland. Both static (e.g., /dev/speaker)
and dynamic (e.g., /dev/bpf*, some removable devices) nodes are
supported. Each DEVFS mount may have a different ruleset assigned to
it, permitting different policies to be implemented for things like
jails.
Approved by: phk
one out of a block cipher. This has 2 advantages:
1) The code is _much_ simpler
2) We aren't committing our security to one algorithm (much as we
may think we trust AES).
While I'm here, make an explicit reseed do a slow reseed instead
of a fast; this is in line with what the original paper suggested.
The file vfs_conf.c which was dealing with root mounting has
been repo-copied into vfs_mount.c to preserve history.
This makes nmount related development easier, and help reducing
the size of vfs_syscalls.c, which is still an enormous file.
Reviewed by: rwatson
Repo-copy by: peter
The ability to schedule multiple threads per process
(one one cpu) by making ALL system calls optionally asynchronous.
to come: ia64 and power-pc patches, patches for gdb, test program (in tools)
Reviewed by: Almost everyone who counts
(at various times, peter, jhb, matt, alfred, mini, bernd,
and a cast of thousands)
NOTE: this is still Beta code, and contains lots of debugging stuff.
expect slight instability in signals..
This code makes use of variable-size kernel representation of rules
(exactly the same concept of BPF instructions, as used in the BSDI's
firewall), which makes firewall operation a lot faster, and the
code more readable and easier to extend and debug.
The interface with the rest of the system is unchanged, as witnessed
by this commit. The only extra kernel files that I am touching
are if_fw.h and ip_dummynet.c, which is quite tied to ipfw. In
userland I only had to touch those programs which manipulate the
internal representation of firewall rules).
The code is almost entirely new (and I believe I have written the
vast majority of those sections which were taken from the former
ip_fw.c), so rather than modifying the old ip_fw.c I decided to
create a new file, sys/netinet/ip_fw2.c . Same for the user
interface, which is in sbin/ipfw/ipfw2.c (it still compiles to
/sbin/ipfw). The old files are still there, and will be removed
in due time.
I have not renamed the header file because it would have required
touching a one-line change to a number of kernel files.
In terms of user interface, the new "ipfw" is supposed to accepts
the old syntax for ipfw rules (and produce the same output with
"ipfw show". Only a couple of the old options (out of some 30 of
them) has not been implemented, but they will be soon.
On the other hand, the new code has some very powerful extensions.
First, you can put "or" connectives between match fields (and soon
also between options), and write things like
ipfw add allow ip from { 1.2.3.4/27 or 5.6.7.8/30 } 10-23,25,1024-3000 to any
This should make rulesets slightly more compact (and lines longer!),
by condensing 2 or more of the old rules into single ones.
Also, as an example of how easy the rules can be extended, I have
implemented an 'address set' match pattern, where you can specify
an IP address in a format like this:
10.20.30.0/26{18,44,33,22,9}
which will match the set of hosts listed in braces belonging to the
subnet 10.20.30.0/26 . The match is done using a bitmap, so it is
essentially a constant time operation requiring a handful of CPU
instructions (and a very small amount of memmory -- for a full /24
subnet, the instruction only consumes 40 bytes).
Again, in this commit I have focused on functionality and tried
to minimize changes to the other parts of the system. Some performance
improvement can be achieved with minor changes to the interface of
ip_fw_chk_t. This will be done later when this code is settled.
The code is meant to compile unmodified on RELENG_4 (once the
PACKET_TAG_* changes have been merged), for this reason
you will see #ifdef __FreeBSD_version in a couple of places.
This should minimize errors when (hopefully soon) it will be time
to do the MFC.
MAKEDEV: Add MAKEDEV glue for the ti(4) device nodes.
ti.4: Update the ti(4) man page to include information on the
TI_JUMBO_HDRSPLIT and TI_PRIVATE_JUMBOS kernel options,
and also include information about the new character
device interface and the associated ioctls.
man9/Makefile: Add jumbo.9 and zero_copy.9 man pages and associated
links.
jumbo.9: New man page describing the jumbo buffer allocator
interface and operation.
zero_copy.9: New man page describing the general characteristics of
the zero copy send and receive code, and what an
application author should do to take advantage of the
zero copy functionality.
NOTES: Add entries for ZERO_COPY_SOCKETS, TI_PRIVATE_JUMBOS,
TI_JUMBO_HDRSPLIT, MSIZE, and MCLSHIFT.
conf/files: Add uipc_jumbo.c and uipc_cow.c.
conf/options: Add the 5 options mentioned above.
kern_subr.c: Receive side zero copy implementation. This takes
"disposable" pages attached to an mbuf, gives them to
a user process, and then recycles the user's page.
This is only active when ZERO_COPY_SOCKETS is turned on
and the kern.ipc.zero_copy.receive sysctl variable is
set to 1.
uipc_cow.c: Send side zero copy functions. Takes a page written
by the user and maps it copy on write and assigns it
kernel virtual address space. Removes copy on write
mapping once the buffer has been freed by the network
stack.
uipc_jumbo.c: Jumbo disposable page allocator code. This allocates
(optionally) disposable pages for network drivers that
want to give the user the option of doing zero copy
receive.
uipc_socket.c: Add kern.ipc.zero_copy.{send,receive} sysctls that are
enabled if ZERO_COPY_SOCKETS is turned on.
Add zero copy send support to sosend() -- pages get
mapped into the kernel instead of getting copied if
they meet size and alignment restrictions.
uipc_syscalls.c:Un-staticize some of the sf* functions so that they
can be used elsewhere. (uipc_cow.c)
if_media.c: In the SIOCGIFMEDIA ioctl in ifmedia_ioctl(), avoid
calling malloc() with M_WAITOK. Return an error if
the M_NOWAIT malloc fails.
The ti(4) driver and the wi(4) driver, at least, call
this with a mutex held. This causes witness warnings
for 'ifconfig -a' with a wi(4) or ti(4) board in the
system. (I've only verified for ti(4)).
ip_output.c: Fragment large datagrams so that each segment contains
a multiple of PAGE_SIZE amount of data plus headers.
This allows the receiver to potentially do page
flipping on receives.
if_ti.c: Add zero copy receive support to the ti(4) driver. If
TI_PRIVATE_JUMBOS is not defined, it now uses the
jumbo(9) buffer allocator for jumbo receive buffers.
Add a new character device interface for the ti(4)
driver for the new debugging interface. This allows
(a patched version of) gdb to talk to the Tigon board
and debug the firmware. There are also a few additional
debugging ioctls available through this interface.
Add header splitting support to the ti(4) driver.
Tweak some of the default interrupt coalescing
parameters to more useful defaults.
Add hooks for supporting transmit flow control, but
leave it turned off with a comment describing why it
is turned off.
if_tireg.h: Change the firmware rev to 12.4.11, since we're really
at 12.4.11 plus fixes from 12.4.13.
Add defines needed for debugging.
Remove the ti_stats structure, it is now defined in
sys/tiio.h.
ti_fw.h: 12.4.11 firmware.
ti_fw2.h: 12.4.11 firmware, plus selected fixes from 12.4.13,
and my header splitting patches. Revision 12.4.13
doesn't handle 10/100 negotiation properly. (This
firmware is the same as what was in the tree previously,
with the addition of header splitting support.)
sys/jumbo.h: Jumbo buffer allocator interface.
sys/mbuf.h: Add a new external mbuf type, EXT_DISPOSABLE, to
indicate that the payload buffer can be thrown away /
flipped to a userland process.
socketvar.h: Add prototype for socow_setup.
tiio.h: ioctl interface to the character portion of the ti(4)
driver, plus associated structure/type definitions.
uio.h: Change prototype for uiomoveco() so that we'll know
whether the source page is disposable.
ufs_readwrite.c:Update for new prototype of uiomoveco().
vm_fault.c: In vm_fault(), check to see whether we need to do a page
based copy on write fault.
vm_object.c: Add a new function, vm_object_allocate_wait(). This
does the same thing that vm_object allocate does, except
that it gives the caller the opportunity to specify whether
it should wait on the uma_zalloc() of the object structre.
This allows vm objects to be allocated while holding a
mutex. (Without generating WITNESS warnings.)
vm_object_allocate() is implemented as a call to
vm_object_allocate_wait() with the malloc flag set to
M_WAITOK.
vm_object.h: Add prototype for vm_object_allocate_wait().
vm_page.c: Add page-based copy on write setup, clear and fault
routines.
vm_page.h: Add page based COW function prototypes and variable in
the vm_page structure.
Many thanks to Drew Gallatin, who wrote the zero copy send and receive
code, and to all the other folks who have tested and reviewed this code
over the years.
a small chance that it might have broken loading the miibus, so err on
the side of caution until I can figure out what is going on. This
backs out all but the PCI, PCIB and ISA bus interfaces being
"standard," which have been well tested...
easier loading of modules that might refer to these interfaces. None
of the code that implements them is standard, just the glue. This
bloats the kernel a whopping 8k.
Silence on: arch@
so that /dev/mumble can be the entrypoint to some networking graph,
e.g. a tunnel or a remote tape drive or whatever...
Not fully tested (by me) yet.
Submitted by: Mark Santcroos <marks@ripe.net>
MFC after: 3 weeks
is currently conditional on both the GEOM and GEOM_GPT options to
avoid getting GPT by default and having the MBR and GPT classes
clash.
The correct behaviour of the MBR class would be to back-off (reject)
a MBR if it's a Protective MBR (a MBR with a single partition of type
0xEE that spans the whole disk (as far as the MBR is concerned).
The correct behaviour if the GPT class would be to back-off (reject)
a GPT if there's a MBR that's not a Protective MBR.
At this stage it's inconvenient to destroy a good MBR when working
with GPTs that it's more convenient to have the MBR class back-off
when it detects the GPT signature on disk and have the GPT class
ignore the MBR.
In sys/gpt.h UUIDs (GUIDs) for the following FreeBSD partitions
have been defined:
GPT_ENT_TYPE_FREEBSD
FreeBSD slice with disklabel. This is the equivalent of
the well-known FreeBSD MBR partition type.
GPT_ENT_TYPE_FREEBSD_{SWAP|UFS|UFS2|VINUM}
FreeBSD partitions in the context of disklabel. This is
speculating on the idea to use the GPT to hold partitions
instead if slices and removing the fixed (and low) limits
we have on the number of partitions.
This commit lacks a GPT image for the regression suite.
The uuidgen command, by means of the uuidgen syscall, generates one
or more Universally Unique Identifiers compatible with OSF/DCE 1.1
version 1 UUIDs.
From the Perforce logs (change 11995):
Round of cleanups:
o Give uuidgen() the correct prototype in syscalls.master
o Define struct uuid according to DCE 1.1 in sys/uuid.h
o Use struct uuid instead of uuid_t. The latter is defined
in sys/uuid.h but should not be used in kernel land.
o Add snprintf_uuid(), printf_uuid() and sbuf_printf_uuid()
to kern_uuid.c for use in the kernel (currently geom_gpt.c).
o Rename the non-standard struct uuid in kern/kern_uuid.c
to struct uuid_private and give it a slightly better definition
for better byte-order handling. See below.
o In sys/gpt.h, fix the broken uuid definitions to match the now
compliant struct uuid definition. See below.
o In usr.bin/uuidgen/uuidgen.c catch up with struct uuid change.
A note about byte-order:
The standard failed to provide a non-conflicting and
unambiguous definition for the binary representation. My initial
implementation always wrote the timestamp as a 64-bit little-endian
(2s-complement) integral. The clock sequence was always written
as a 16-bit big-endian (2s-complement) integral. After a good
nights sleep and couple of Pan Galactic Gargle Blasters (not
necessarily in that order :-) I reread the spec and came to the
conclusion that the time fields are always written in the native
by order, provided the the low, mid and hi chopping still occurs.
The spec mentions that you "might need to swap bytes if you talk
to a machine that has a different byte-order". The clock sequence
is always written in big-endian order (as is the IEEE 802 address)
because its division is resulting in bytes, making the ordering
unambiguous.
"The only hard problem in cryptography is key-management."
All sectors are encrypted with AES in CBC mode using a constant key,
currently compiled in and all zero.
To activate this module, write the magic header on the partition:
echo "<<FreeBSD-GEOM-AES>>" | dd conv=sync of=/dev/md98
The encrypted device will be one sector shorter and have ".aes"
appended to its name.
Sponsored by: DARPA & NAI Labs.
IFS had its fingers deep in the belly of the UFS/FFS split. IFS
will be reimplemented by the maintainer at a later date.
Requested by: adrian (maintainer)
shared code and converting all ufs references. Originally it may
have made sense to share common features between the two filesystems,
but recently it has only caused problems, the UFS2 work being the
final straw.
All UFS_* indirect calls are now direct calls to ext2_* functions,
and ext2fs-specific mount and inode structures have been introduced.
0xdeadc0de and then check for it just before memory is handed off as part
of a new request. This will catch any post free/pre alloc modification of
memory, as well as introduce errors for anything that tries to dereference
it as a pointer.
This code takes the form of special init, fini, ctor and dtor routines that
are specificly used by malloc. It is in a seperate file because additional
debugging aids will want to live here as well.
ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
time-of-day clocks, ported from NetBSD. The front-ends are expected
to be at least partly machine-dependent; the sparc64 EBus and SBus
ones will be commited to MD directories for now (in a subsequent commit).
a set of helper routines to deal with real-time clocks. The generic
functions access the clock diver using a kobj interface. This is intended
to reduce code reduplication and make it easy to support more than one
clock model on a single architecture.
This code is currently only used on sparc64, but it is planned to convert
the code of the other architectures to it later.
I have not been able to find very much information about the PC98
extended partition layout so this is gleaned from the source in
our pc98 architecture. Corrections and patched very welcome.
Sponsored by: DARPA and NAI Labs.
The detection code in this method is written so that it should work on
all architectures which means that you can plug a Sun disk into a i386
now and access the partitions.
We still need an endian-agnostic ufs/ffs before this is really
interresting, but the main focus was to get sparc64 onto the GEOM
trail.
This makes other power-management system (APM for now) to be able to
generate power profile change events (ie. AC-line status changes), and
other kernel components, not only the ACPI components, can be notified
the events.
- move subroutines in acpi_powerprofile.c (removed) to kern/subr_power.c
- call power_profile_set_state() also from APM driver when AC-line
status changes
- add call-back function for Crusoe LongRun controlling on power
profile changes for a example
buffer length, determine if the pointer is to a valid string. Currently,
the only check is whether a '\0' appears in the buffer. This is useful
when pulling in a structure from userland that may contain one or more
strings, and validity testing must be performed on elements of the
structure. When copying normal string arguments, copyinstr() is
expected to be used.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
Remove the explicit call to aio_proc_rundown() from exit1(), instead AIO
will use at_exit(9).
Add functions at_exec(9), rm_at_exec(9) which function nearly the
same as at_exec(9) and rm_at_exec(9), these functions are called
on behalf of modules at the time of execve(2) after the image
activator has run.
Use a modified version of tegge's suggestion via at_exec(9) to close
an exploitable race in AIO.
Fix SYSCALL_MODULE_HELPER such that it's archetecuterally neutral,
the problem was that one had to pass it a paramater indicating the
number of arguments which were actually the number of "int". Fix
it by using an inline version of the AS macro against the syscall
arguments. (AS should be available globally but we'll get to that
later.)
Add a primative system for dynamically adding kqueue ops, it's really
not as sophisticated as it should be, but I'll discuss with jlemon when
he's around.
cardbus in the kernel, not on all the bridges that implement it.
Note: this is NEWCARD only, so we don't want it for the 'card' case,
unlike card_if.m, which is both NEWCARD and OLDCARD.
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
"[...] and removes the hostcache code from standard kernels---the
code that depends on it is not going to happen any time soon,
I'm afraid."
Time to clean up.
- Now that apm loadable module can inform its existence to other kernel
components (e.g. i386/isa/clock.c:startrtclock()'s TCS hack).
- Exchange priority of SI_SUB_CPU and SI_SUB_KLD for above purpose.
- Add simple arbitration mechanism for APM vs. ACPI. This prevents
the kernel enables both of them.
- Remove obsolete `#ifdef DEV_APM' related code.
- Add abstracted interface for Powermanagement operations. Public apm(4)
functions, such as apm_suspend(), should be replaced new interfaces.
Currently only power_pm_suspend (successor of apm_suspend) is implemented.
Reviewed by: peter, arch@ and audit@
Until now, the ptrace syscall was implemented as a wrapper that called
various functions in procfs depending on which ptrace operation was
requested. Most of these functions were themselves wrappers around
procfs_{read,write}_{,db,fp}regs(), with only some extra error checks,
which weren't necessary in the ptrace case anyway.
This commit moves procfs_rwmem() from procfs_mem.c into sys_process.c
(renaming it to proc_rwmem() in the process), and implements ptrace()
directly in terms of procfs_{read,write}_{,db,fp}regs() instead of
having it fake up a struct uio and then call procfs_do{,db,fp}regs().
It also moves the prototypes for procfs_{read,write}_{,db,fp}regs()
and proc_rwmem() from proc.h to ptrace.h, and marks all procfs files
except procfs_machdep.c as "optional procfs" instead of "standard".
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
- All sources are built in a single object, reducing namespace pollution.
- Kill the ready queue, and handle a busy response to mly_start in callers
rather than deferring the command.
- Improve our interaction with CAM:
- Don't advertise physical channels as SCSI busses by default.
- use the SIM queue freeze capability rather than queueing CDBs internally.
- force bus reprobe at module load time.
- Clean up more resources in mly_free.
- Tidy up debugging levels.
- Tidy up handling of events (mostly just code cleanliness).
- Use explanatory macros for operations on bus/target/channel numbers.
directories. When enabled via "options UFS_DIRHASH", in-core hash
arrays are maintained for large directories. These allow all
directory operations to take place quickly instead of requiring
long linear searches. For now anyway, dirhash is not enabled by
default.
The in-core hash arrays have a memory requirement that is approximately
half the size of the size of the on-disk directory file. A number
of new sysctl variables allow control over which directories get
hashed and over the maximum amount of memory that dirhash will use:
vfs.ufs.dirhash_minsize
The minimum on-disk directory size for which hashing should be
used. The default is 2560 (2.5k).
vfs.ufs.dirhash_maxmem
The system-wide maximum total memory to be used by dirhash data
structures. The default is 2097152 (2MB).
The current amount of memory being used by dirhash is visible
through the read-only sysctl variable vfs.ufs.dirhash_maxmem.
Finally, some extra sanity checks that are enabled by default, but
which may have an impact on performance, can be disabled by setting
vfs.ufs.dirhash_docheck to 0.
Discussed on: -fs, -hackers
Also removed some spl's and added some VM mutexes, but they are not actually
used yet, so this commit does not really make any operational changes
to the system.
vm_page.c relates to vm_page_t manipulation, including high level deactivation,
activation, etc... vm_pageq.c relates to finding free pages and aquiring
exclusive access to a page queue (exclusivity part not yet implemented).
And the world still builds... :-)
- Move the lance_probe function to if_lnc.c.
- Support C-NET(98)S again.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata) and nyan
No response from: Paul Richards
removed and a minimal number of changes to make it compile in the new
location.
# I have a fully converted on a disk that may be crashed. If it is
# crashed, I'll redo the work.
introduce a modified allocation mechanism for mbufs and mbuf clusters; one
which can scale under SMP and which offers the possibility of resource
reclamation to be implemented in the future. Notable advantages:
o Reduce contention for SMP by offering per-CPU pools and locks.
o Better use of data cache due to per-CPU pools.
o Much less code cache pollution due to excessively large allocation macros.
o Framework for `grouping' objects from same page together so as to be able
to possibly free wired-down pages back to the system if they are no longer
needed by the network stacks.
Additional things changed with this addition:
- Moved some mbuf specific declarations and initializations from
sys/conf/param.c into mbuf-specific code where they belong.
- m_getclr() has been renamed to m_get_clrd() because the old name is really
confusing. m_getclr() HAS been preserved though and is defined to the new
name. No tree sweep has been done "to change the interface," as the old
name will continue to be supported and is not depracated. The change was
merely done because m_getclr() sounds too much like "m_get a cluster."
- TEMPORARILY disabled mbtypes statistics displaying in netstat(1) and
systat(1) (see TODO below).
- Fixed systat(1) to display number of "free mbufs" based on new per-CPU
stat structures.
- Fixed netstat(1) to display new per-CPU stats based on sysctl-exported
per-CPU stat structures. All infos are fetched via sysctl.
TODO (in order of priority):
- Re-enable mbtypes statistics in both netstat(1) and systat(1) after
introducing an SMP friendly way to collect the mbtypes stats under the
already introduced per-CPU locks (i.e. hopefully don't use atomic() - it
seems too costly for a mere stat update, especially when other locks are
already present).
- Optionally have systat(1) display not only "total free mbufs" but also
"total free mbufs per CPU pool."
- Fix minor length-fetching issues in netstat(1) related to recently
re-enabled option to read mbuf stats from a core file.
- Move reference counters at least for mbuf clusters into an unused portion
of the cluster itself, to save space and need to allocate a counter.
- Look into introducing resource freeing possibly from a kproc.
Reviewed by (in parts): jlemon, jake, silby, terry
Tested by: jlemon (Intel & Alpha), mjacob (Intel & Alpha)
Preliminary performance measurements: jlemon (and me, obviously)
URL: http://people.freebsd.org/~bmilekic/mb_alloc/
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
memory I/O space. Otherwise, our resource allocation system might
mistakenly assign pccard, plug and play devices or other things
addresses that conflict with ROMs.
I cleaned up his code a little from the submited driver: style(9)
issues, commentary on why something that looks incorrect really is
correct. Also noted that while a checksum field is defined for the
ROMs, enough common hardware neglects it to make it not worthwhile
checking.
Submitted by: Nikolai Saoukh <nms@otdel-1.org>
PR: 22078
This closes a minor information leak which allows a remote observer to
determine the rate at which the machine is generating packets, since the
default behaviour is to increment a counter for each packet sent.
Reviewed by: -net
Obtained from: OpenBSD
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
Add a CAPI (hardware independent) driver i4bcapi(4) and hardware driver
iavc (4) to support active CAPI-based BRI and PRI cards (currently AVM
B1 and T1 cards) to isdn4bsd.
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
soon attach directly to pcic rather than the kludge pci-pcic device we
have now.
In some ways, this is similar to the work PAO3 did to try to support
cardbus bridges. In some ways different. This and future commits
will be taking from the spirit of many of those changes. pcicvar.h is
completely different from the pcicvar.h that appeared in PAO3, but
similar in concept.
If for some reason DEVFS is undesired, the "NODEVFS" option is
needed now.
Pending any significant issues, DEVFS will be made mandatory in
-current on july 1st so that we can start reaping the full
benefits of having it.
of the pcic class of devices. Go ahead and move it to the "usual"
place. I say "usual" in quotes since it isn't exactly right (not in
dev/blah), but it is closer than before.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
been made machine independent and various other adjustments have been made
to support Alpha SMP.
- It splits the per-process portions of hardclock() and statclock() off
into hardclock_process() and statclock_process() respectively. hardclock()
and statclock() call the *_process() functions for the current process so
that UP systems will run as before. For SMP systems, it is simply necessary
to ensure that all other processors execute the *_process() functions when the
main clock functions are triggered on one CPU by an interrupt. For the alpha
4100, clock interrupts are delievered in a staggered broadcast fashion, so
we simply call hardclock/statclock on the boot CPU and call the *_process()
functions on the secondaries. For x86, we call statclock and hardclock as
usual and then call forward_hardclock/statclock in the MD code to send an IPI
to cause the AP's to execute forwared_hardclock/statclock which then call the
*_process() functions.
- forward_signal() and forward_roundrobin() have been reworked to be MI and to
involve less hackery. Now the cpu doing the forward sets any flags, etc. and
sends a very simple IPI_AST to the other cpu(s). AST IPIs now just basically
return so that they can execute ast() and don't bother with setting the
astpending or needresched flags themselves. This also removes the loop in
forward_signal() as sched_lock closes the race condition that the loop worked
around.
- need_resched(), resched_wanted() and clear_resched() have been changed to take
a process to act on rather than assuming curproc so that they can be used to
implement forward_roundrobin() as described above.
- Various other SMP variables have been moved to a MI subr_smp.c and a new
header sys/smp.h declares MI SMP variables and API's. The IPI API's from
machine/ipl.h have moved to machine/smp.h which is included by sys/smp.h.
- The globaldata_register() and globaldata_find() functions as well as the
SLIST of globaldata structures has become MI and moved into subr_smp.c.
Also, the globaldata list is only available if SMP support is compiled in.
Reviewed by: jake, peter
Looked over by: eivind
