thread for each interrupt that comes in. If we don't, log the event and
return immediately for a hardware interrupt. For a softinterrupt, panic
instead.
Submitted by: ben
The code for suspend/resume is derived from APM device driver.
Some people suggested the original code is somewhat buggy, but I'd
like to just move it from apm.c without any major changes for the
initial version. This code should be refined later.
To use pmtimer to adjust time at resume time, add
device pmtimer
in your kernel config file, and add
hint.pmtimer.0.at="isa"
in your device.hints
Reviewed by: -current, bde
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
in the boot. The cleanup must be done in one of the few ways that
db_numargs() understands, so that early backtraces in ddb don't underrun
the stack. The underruns caused reboots a few years ago when there
was an unmapped page above the stack (trapping to abort the command
doesn't work early).
Cleaned up some nearby code.
curproc was initialized. curproc == NULL was interpreted as matching
the process holding Giant... Just skip mtx_enter() and mtx_exit() in
trap() if (curproc == NULL && cold) (&& cold for safety).
don't take an arg, but swi_generic() is special in order to avoid one
whole conditional branch in the old SWI dispatch code. The new SWI
dispatch code passed it a garbage arg. Bypass swi_generic() and call
swi_dispatcher() directly, like the corresponding alpha code has always
done.
The panic was rare because because it only occurred if more than one
of the {sio,cy,rc} drivers was configured and one was active, and the
cy driver doesn't even compile.
macros that expand to pass filename and line number information. This is
necessary since we're using inline functions instead of macros now.
Add const to the filename pointers passed througout the mtx and witness
code.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
Some have dual host->PCI bridges for the same logical pci bus (!), eg:
some of the RCC chipsets. This is a 32/64 bit 33/66MHz and dual pci
voltage motherboard so persumably there are electical or signalling
differences but they are otherwise the same logical bus.
The new PCI probe code however was getting somewhat upset about it and
ended up creating two pci bridges to the same logical bus, which caused
devices on that logical bus to appear and be probed twice.
The ACPI data on this box correctly identifies this stuff, so bring on
ACPI! :-)
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
pcib_set_bus() cannot be used on the new child because it is
meant to be used on the *pci* device (it looks at the parent internally)
not the pcib being added. Bite the bullet and use ivars for the bus
number to avoid any doubts about whether the softc is consistant between
probe and attach. This should not break the Alpha code.
