le*dec / le*enc functions.
Replace net80211 specific macros with system-wide bytestream
encoding/decoding functions:
- LE_READ_2 -> le16dec
- LE_READ_4 -> le32dec
- LE_WRITE_2 -> le16enc
- LE_WRITE_4 -> le32enc
+ drop ieee80211_input.h include, where it was included for these
operations only.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6030
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
to get upset.
The Qualcomm Atheros reference design code goes through significant
hacks to shut down RX before TX. It doesn't even try do do it in the
driver - it actually makes the DMA stop routines in the HAL shut down
RX before shutting down TX.
So, to make this work for chips that aren't the AR9380 and later, do
it in the driver. Shuffle the TX stop/drain HAL calls to be called
*after* the RX stop HAL call.
Tested:
* AR5413 (STA)
* AR5212 (STA)
* AR5416 (STA)
* AR9380 (STA)
* AR9331 (AP)
* AR9341 (AP)
TODO:
* test ar92xx series NIC and the AR5210/AR5211, in case there's something
even odder about those.
fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
directly referencing ni->ni_txpower.
This provides the hardware with a slightly more accurate idea of
the maximum TX power to be using.
This is part of a series to get per-packet TPC to work (better).
Tested:
* AR5416, hostap mode
(Yes, the previous code temporarily broke EDMA TX. I'm sorry; I should've
actually setup ATH_BUF_FIFOEND on frames so txq->axq_fifo_depth was
cleared!)
This code implements a whole bunch of sorely needed EDMA TX improvements
along with CABQ TX support.
The specifics:
* When filling/refilling the FIFO, use the new TXQ staging queue
for FIFO frames
* Tag frames with ATH_BUF_FIFOPTR and ATH_BUF_FIFOEND correctly.
For now the non-CABQ transmit path pushes one frame into the TXQ
staging queue without setting up the intermediary link pointers
to chain them together, so draining frames from the txq staging
queue to the FIFO queue occurs AMPDU / MPDU at a time.
* In the CABQ case, manually tag the list with ATH_BUF_FIFOPTR and
ATH_BUF_FIFOEND so a chain of frames is pushed into the FIFO
at once.
* Now that frames are in a FIFO pending queue, we can top up the
FIFO after completing a single frame. This means we can keep
it filled rather than waiting for it drain and _then_ adding
more frames.
* The EDMA restart routine now walks the FIFO queue in the TXQ
rather than the pending queue and re-initialises the FIFO with
that.
* When restarting EDMA, we may have partially completed sending
a list. So stamp the first frame that we see in a list with
ATH_BUF_FIFOPTR and push _that_ into the hardware.
* When completing frames, only check those on the FIFO queue.
We should never ever queue frames from the pending queue
direct to the hardware, so there's no point in checking.
* Until I figure out what's going on, make sure if the TXSTATUS
for an empty queue pops up, complain loudly and continue.
This will stop the panics that people are seeing. I'll add
some code later which will assist in ensuring I'm populating
each descriptor with the correct queue ID.
* When considering whether to queue frames to the hardware queue
directly or software queue frames, make sure the depth of
the FIFO is taken into account now.
* When completing frames, tag them with ATH_BUF_BUSY if they're
not the final frame in a FIFO list. The same holding descriptor
behaviour is required when handling descriptors linked together
with a link pointer as the hardware will re-read the previous
descriptor to refresh the link pointer before contiuning.
* .. and if we complete the FIFO list (ie, the buffer has
ATH_BUF_FIFOEND set), then we don't need the holding buffer
any longer. Thus, free it.
Tested:
* AR9380/AR9580, STA and hostap
* AR9280, STA/hostap
TODO:
* I don't yet trust that the EDMA restart routine is totally correct
in all circumstances. I'll continue to thrash this out under heavy
multiple-TXQ traffic load and fix whatever pops up.
instead of axq_link.
This (among a bunch of uncommitted work) is required for EDMA chips
to correctly transmit frames on the CABQ.
Tested:
* AR9280, hostap mode
* AR9380/AR9580, hostap mode (staggered beacons)
TODO:
* This code only really gets called when burst beacons are used;
it glues multiple CABQ queues together when sending to the hardware.
* More thorough bursted beacon testing! (first requires some work with
the beacon queue code for bursted beacons, as that currently uses the
link pointer and will fail on EDMA chips.)
related issues.
Moving the TX locking under one lock made things easier to progress on
but it had one important side-effect - it increased the latency when
handling CABQ setup when sending beacons.
This commit introduces a bunch of new changes and a few unrelated changs
that are just easier to lump in here.
The aim is to have the CABQ locking separate from other locking.
The CABQ transmit path in the beacon process thus doesn't have to grab
the general TX lock, reducing lock contention/latency and making it
more likely that we'll make the beacon TX timing.
The second half of this commit is the CABQ related setup changes needed
for sane looking EDMA CABQ support. Right now the EDMA TX code naively
assumes that only one frame (MPDU or A-MPDU) is being pushed into each
FIFO slot. For the CABQ this isn't true - a whole list of frames is
being pushed in - and thus CABQ handling breaks very quickly.
The aim here is to setup the CABQ list and then push _that list_ to
the hardware for transmission. I can then extend the EDMA TX code
to stamp that list as being "one" FIFO entry (likely by tagging the
last buffer in that list as "FIFO END") so the EDMA TX completion code
correctly tracks things.
Major:
* Migrate the per-TXQ add/removal locking back to per-TXQ, rather than
a single lock.
* Leave the software queue side of things under the ATH_TX_LOCK lock,
(continuing) to serialise things as they are.
* Add a new function which is called whenever there's a beacon miss,
to print out some debugging. This is primarily designed to help
me figure out if the beacon miss events are due to a noisy environment,
issues with the PHY/MAC, or other.
* Move the CABQ setup/enable to occur _after_ all the VAPs have been
looked at. This means that for multiple VAPS in bursted mode, the
CABQ gets primed once all VAPs are checked, rather than being primed
on the first VAP and then having frames appended after this.
Minor:
* Add a (disabled) twiddle to let me enable/disable cabq traffic.
It's primarily there to let me easily debug what's going on with beacon
and CABQ setup/traffic; there's some DMA engine hangs which I'm finally
trying to trace down.
* Clear bf_next when flushing frames; it should quieten some warnings
that show up when a node goes away.
Tested:
* AR9280, STA/hostap, up to 4 vaps (staggered)
* AR5416, STA/hostap, up to 4 vaps (staggered)
TODO:
* (Lots) more AR9380 and later testing, as I may have missed something here.
* Leverage this to fix CABQ hanling for AR9380 and later chips.
* Force bursted beaconing on the chips that default to staggered beacons and
ensure the CABQ stuff is all sane (eg, the MORE bits that aren't being
correctly set when chaining descriptors.)
when an interface is going down.
Right now it's quite possible (but very unlikely!) that ath_reset()
or similar is called, leading to a beacon config call, in parallel with
the last VAP being destroyed.
This likely should be fixed by making sure the bmiss/bstuck/watchdog
taskqueues are canceled whenever the last VAP is destroyed.
I couldn't think of a way to maintain the hardware TXQ locks _and_ layer
on top of that per-TXQ software queuing and any other kind of fine-grained
locks (eg per-TID, or per-node locks.)
So for now, to facilitate some further code refactoring and development
as part of the final push to get software queue ps-poll and u-apsd handling
into this driver, just do away with them entirely.
I may eventually bring them back at some point, when it looks slightly more
architectually cleaner to do so. But as it stands at the present, it's
not really buying us much:
* in order to properly serialise things and not get bitten by scheduling
and locking interactions with things higher up in the stack, we need to
wrap the whole TX path in a long held lock. Otherwise we can end up
being pre-empted during frame handling, resulting in some out of order
frame handling between sequence number allocation and encryption handling
(ie, the seqno and the CCMP IV get out of sequence);
* .. so whilst that's the case, holding the lock for that long means that
we're acquiring and releasing the TXQ lock _inside_ that context;
* And we also acquire it per-frame during frame completion, but we currently
can't hold the lock for the duration of the TX completion as we need
to call net80211 layer things with the locks _unheld_ to avoid LOR.
* .. the other places were grab that lock are reset/flush, which don't happen
often.
My eventual aim is to change the TX path so all rejected frame transmissions
and all frame completions result in any ieee80211_free_node() calls to occur
outside of the TX lock; then I can cut back on the amount of locking that
goes on here.
There may be some LORs that occur when ieee80211_free_node() is called when
the TX queue path fails; I'll begin to address these in follow-up commits.
EDMA HAL hardware.
* The EDMA HAL code assumes the nexttbtt and intval values are in TU/8
units, rather than TU. For now, just "hack" around that here, at least
until I code up something to translate it in the HAL.
* Setup some different TXQ flags for EDMA hardware.
* The EDMA HAL doesn't support setting the first rate series via
ath_hal_setuptxdesc() - instead, a call to ath_hal_set11nratescenario()
is always required. So for now, just do an 11n rate series setup
for EDMA beacon frames.
This allows my AR9380 to successfully transmit beacon frames.
However, CABQ TX and all normal data frame TX and TX completion is
still not functional and will require some more significant code churn
to make work.
The existing API only exposes 'seglen' (the current buffer (segment) length)
with the data buffer pointer set in 'ds_data'. This is fine for the legacy
DMA engine but it won't work for the EDMA engines.
The EDMA engine has a significantly different TX descriptor layout.
* The legacy DMA engine had a ds_data pointer at the same offset in the
descriptor for both TX and RX buffers;
* The EDMA engine has no ds_data for RX - the data is DMAed after the
descriptor;
* The EDMA engine has support for 4 TX buffer/segment pairs in the TX
DMA descriptor;
* The EDMA TX completion is in a different FIFO, and the driver will
'link' the status completion entry to a QCU by a "QCU ID".
I don't know why it's just not filled in by the hardware, alas.
So given that, here are the changes:
* Instead of directly fondling 'ds_data' in ath_desc, change the
ath_hal_filltxdesc() to take an array of buffer pointers as well
as segment len pointers;
* The EDMA TX completion status wants a descriptor and queue id.
This (for now) uses bf_state.bfs_txq and will extract the hardware QCU
ID from that.
* .. and this is ugly and wasteful; it should change to just store
the QCU in the bf_state and save 3/7 bytes in the process.
Now, the weird crap:
* The aggregate TX path was using bf_state->bfs_txq for the TXQ, rather than
taking a function argument. I've tidied that up.
* The multicast queue frames get put on a software TXQ and then that is
appended to the hardware CABQ when appropriate. So for now, make sure
that bf_state->bfs_txq points at the CABQ when adding frames to the
multicast queue.
* .. but the multicast queue TX path for now doesn't use the software
queue and instead
(a) directly sets up the descriptor contents at that point;
(b) the frames on the vap->avp_mcastq are then just appended wholesale
to the CABQ.
So for now, I don't have to worry about making the multicast path
work with aggregation or the per-TID software queue. Phew.
What's left to do:
* I need to modify the 11n ath_hal_chaintxdesc() API to do the same.
I'll do that in a subsequent commit.
* Remove bf_state.bfs_txq entirely and store the QCU as appropriate.
* .. then do the runtime "is this going on the right HWQ?" checks using
that, rather than comparing pointer values.
Tested on:
* AR9280 STA/AP
* AR5416 STA/AP
TX descriptor link pointers.
This is required for the AR93xx and later chipsets.
The RX path is slightly different - the legacy RX path directly
accesses ath_desc->ds_link for now, however this isn't at all done
for EDMA (FIFO) RX.
Now, for those performing a little software archeology here:
This is all a bit sub-optimal. "struct ath_desc" is only really relevant
for the pre-AR93xx NICs - where ds_link and ds_data is always in the
same location.
The AR93xx and later NICs have different descriptor layouts altogether.
Now, for AR93xx and later NICs, you should never directly reference
ds_link and ds_data, as:
* the RX descriptors don't have either - the data is _after_ the RX
descriptor. They're just one large buffer. There's also no need for
a per-descriptor RX buffer size as they're all fixed sizes.
* the TX descriptors have 4 buffer and 4 length fields _and_ a link
pointer. Each frame takes up one TX FIFO pointer, but it can contain
multiple subframes (either multiple frames in a buffer, and/or
multiple frames in an aggregate/RIFS burst.)
* .. so, when TX frames are queued to a hardware queue, the link
pointer is ONLY for buffers in that frame/aggregate. The next frame
starts in a new FIFO pointer.
* Finally, descriptor completion status is in a different ring.
I'll write something up about that when its time to do so.
This was inspired by Linux ath9k and the reference driver but is a
reimplementation.
Obtained from: Linux ath9k, Qualcomm Atheros
