found on Adaptec AIC-6915 Starfire ethernet controller.
While here, use status register to know resolved speed/duplex.
With this change, sf(4) correctly reports speed/duplex of
established link.
Reviewed by: marius
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
- Use mii_phy_add_media() instead of mii_add_media(). I'm not sure how
this driver actually managed to work before as mii_add_media() is
intended to be used to gether with mii_anar() while mii_phy_add_media()
is intended to be used with mii_phy_setmedia(), however this driver
mii_add_media() along with mii_phy_setmedia().
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
different PHY instance being selected and isolation out into the wrappers
around the service methods rather than duplicating them over and over
again (besides, a PHY driver shouldn't need to care about which instance
it actually is).
- Centralize the check for the need to isolate a non-zero PHY instance not
supporting isolation in mii_mediachg() and just ignore it rather than
panicing, which should sufficient given that a) things are likely to
just work anyway if one doesn't plug in more than one port at a time and
b) refusing to attach in this case just leaves us in a unknown but most
likely also not exactly correct configuration (besides several drivers
setting MIIF_NOISOLATE didn't care about these anyway, probably due to
setting this flag for no real reason).
- Minor fixes like removing unnecessary setting of sc->mii_anegticks,
using sc->mii_anegticks instead of hardcoded values etc.
sn(4) driver and also looking at newer drivers. The reason for the rewrite is
to support MII and to try and resolve some performance issues found when trying
to use the sn(4) driver on the Gumstix network boards.
For reference, the SMSC LAN91C111 is a non-PCI ethernet part whose lineage
dates back to Ye Olde Days of ISA. It seems to get some use in the embedded
space these days on parts lacking on-board MACs or on-board PCI controllers,
such as the XScale PXA line of ARM CPUs.
This also includes a driver for the SMSC LAN83C183 10/100 PHY.
Man page to follow.
