Although this may not be what the original sysctl was designed to do,
it feels a bit more "expected".
Before, if ANI is disabled, the initial ANI parameters are still written
to the hardware, even if they're not enabled. "ANI enabled" would then
adjust the noise immunity parameters dynamically. Disabling ANI would
simply leave the existing noise immunity parameters where they are,
and disable the dynamic part.
The problem is that disabling ANI doesn't leave the hardware in
a consistent, predictable state - so asking a user to disable ANI
wouldn't actually reset the NIC to a consistent set of PHY signal
detection parameters, resulting in an unpredictable/unreliable outcome.
This makes it difficult to get reliable debugging information from
the user.
Approved by: re (kib)
coordinates, such as digitizers and touch-screens, leaving these devices
to uhid(4) and user-level. Specially patched xf86-input-mouse driver can
handle them, that isn't done and can't be done properly with ums(4)
because of mouse(4) protocol limitations.
Approved by: re (kib)
Slot field of the PxCMD register may point to an empty command slot.
That breaks command timeout detection logic, making impossible to find
what command actually caused timeout, and leading to infinite wait.
Workaround that by checking whether pointed command slot is really used
and can timeout in its time. And if not, fallback to the dumb algorithm
used with FBS -- let all commands to time out and then fail all of them.
Approved by: re (kib)
MFC after: 1 week
the right SIM in case the HBA is RAID-capable but the target in question is
not a hot spare or member of a RAID volume.
- Report the loss and addition of SAS and SATA targets detected via PHY link
status changes and signalled by MPI_EVENT_SAS_DEVICE_STATUS_CHANGE to cam(4)
as lost devices and trigger rescans as appropriate. Without this it can take
quite some time until a lost device actually is no longer tried to be used,
if it ever stops. [1]
- Handle MPI_EVENT_IR2, MPI_EVENT_LOG_ENTRY_ADDED, MPI_EVENT_SAS_DISCOVERY
and MPI_EVENT_SAS_PHY_LINK_STATUS silently as these serve no additional
purpose beyond adding cryptic entries to logs.
Thanks to Hans-Joerg Sirtl for providing one of the HBAs these changes were
developed with and RIP to the mainboard that didn't survive testing them.
PR: 157534 [1]
Approved by: re (kib)
MFC after: 2 weeks
- Sprinkle some const where appropriate.
- Consistently use target_id_t for the target parameter of mpt_map_physdisk()
and mpt_is_raid_volume().
- Fix some whitespace bugs.
Approved by: re (kib)
accessing SATA registers. Unserialized access under heavy load caused
wrong speed reporting and potentially could cause device loss.
- To free memory and other resources (including above), allocated
during chipinit() method call on attach, add new chipdeinit() method,
called during driver detach.
Submitted by: Andrew Boyer <aboyer@averesystems.com> (initial version)
Approved by: re (kib)
MFC after: 1 week
Since no actual radar data is ever handled, this won't
do anything. It's mostly here as a reference for those who
wish to experiment with radar detection.
Approved by: re (kib)
the resource covers the entire range. Some BIOSes appear to mark
endpoints as non-fixed incorrectly (non-fixed endpoints are supposed to
be used in _PRS when OSPM is allowed to allocate a certain chunk of
address space within a larger range, I don't believe it is supposed to be
used for _CRS).
Approved by: re (kib)
ioctl interface for DFS modules to use.
Since there's no open source dfs code yet, this doesn't introduce any
operational changes.
Approved by: re (kib)
tools.
* introduce pe_enabled, which (will) indicate whether the radar
detection stuff is enabled or not. Right now it's incorrectly
set, based on something previously written. I'll sort it out
later.
* Don't set HAL_PHYERR_PARAM_ENABLE in pe_relstep to say whether
radar detection is on.
* Return whether blockradar, fir128 and enmaxrssi is enabled.
* Change some of the phyerr params to be integers rather than
HAL_BOOL so they can be set to the NOPARAM value when the
setup function is called. This is in line with other radar
parameters.
* Add new configuration parameters for fir128, blockradar and
enmaxrssi, rather than defaulting to off, on and on respectively.
Approved by: re (kib)
polluting the AR5416 code with later chipset support.
Note: ar9280InitPLL() supports Merlin (AR9280) and later (AR9285, AR9287.)
Submitted by: ssgriffonuser@gmail.com
Approved by: re (kib)
These should be disabled for the AR5416 in hostap/mesh/ibss mode,
as the AR5416 doesn't have support for radar detection on the
ext channel of a HT40 setup. Later chips do.
Approved by: re (kib)
reference driver.
* Australia should use FCC3_WORLD
* Add some new SKUs; these are just the EEPROM values and haven't been
fully defined yet. As such they won't affect anything.
Obtained from: Atheros
Approved by: re (kib)
unknown reason Apple UniNorth2 gem(4) device required manual
interface down/up operation after r222135. Even though this is not
correct thing and I don't like to revert it but it would be better
than breaking gem(4) on PPC. This should be revisited.
PR: kern/157405
Back in 2009 I changed the ABI of the GIO_KEYMAP and PIO_KEYMAP ioctls
to support wide characters. I created a patch to add ABI compatibility
for the old calls, but I didn't get any feedback to that.
It seems now people are upgrading from 8 to 9 they experience this
issue, so add it anyway.
resource allocation on x86 platforms:
- Add a new helper API that Host-PCI bridge drivers can use to restrict
resource allocation requests to a set of address ranges for different
resource types.
- For the ACPI Host-PCI bridge driver, use Producer address range resources
in _CRS to enumerate valid address ranges for a given Host-PCI bridge.
This can be disabled by including "hostres" in the debug.acpi.disabled
tunable.
- For the MPTable Host-PCI bridge driver, use entries in the extended
MPTable to determine the valid address ranges for a given Host-PCI
bridge. This required adding code to parse extended table entries.
Similar to the new PCI-PCI bridge driver, these changes are only enabled
if the NEW_PCIB kernel option is enabled (which is enabled by default on
amd64 and i386).
Approved by: re (kib)
This was removed accidentally when the per HAL instance
code was added, and not reverted when I added back the
global debug variable (for early chip setup debugging.)
supports IPv4/IPv6 checksum offloading and VLAN tag insertion/
stripping as well as WOL. Because uether does not provide a way
to announce driver specific offload capabilities to upper stack,
checksum offloading support needs more work and will be done in
future.
Special thanks to ASIX for donating sample hardware.
H/W donated by: ASIX Electronics
Reviewed by: hselasky
system timer is stopped during shutdown and that the pause() statement in ukbd
causes infinite hang in this regard. The fix is to use mi_switch() instead of
pause() to do the required task switch to ensure that the required USB processes
get executed.
Reported by: Mike_Karels@mcafee.com
MFC after: 1 week
checking IFF_DRV_RUNNING and simplify the code. This also involves holding
the driver lock in the rx_ch callout.
- Just use ifp instead of sc->sc_ifp.
Submitted by: jhb (mostly)
allowing their use to be disabled via device hints though). This matches
what the corresponding Linux driver provided by LSI does. Tested with
SAS1064.
- There's no need to keep track of the RIDs used.
- Don't allocate MSI/MSI-X as RF_SHAREABLE.
- Remove a comment which no longer applies since r209599.
- Assign NULL rather than 0 to pointers.
MFC after: 1 month
bridge is blacklisted. In that case just return from pci_alloc_msix_method(),
otherwise we continue without a single MSI-X resource, causing subsequent
attempts to use the seemingly available resource to fail or when booting
verbose a NULL-pointer dereference of rle->start when trying to print the
IRQ in pci_alloc_msix_method().
Reviewed by: jhb
MFC after: 1 week
- Consistently use the newly introduced sc_mac_rxcfg throughout the driver
instead of reading the old content of CAS_MAC_RX_CONF.
- Increment if_iqdrops instead of if_ierrors in case of RX buffer allocation
failure.
- According to the Cassini datasheet the RX MAC should also be disabled in
cas_setladrf() before changing its configuration.
- Add error messages to gem_disable_{r,t}x() and take advantage of these
throughout the driver instead of duplicating their functionality all over
the place.
sets GEM_MAC_RX_CONFIG based on sc_mac_rxcfg which in turn is initialized
to zero, before reading the supposedly default configuration we were
effectively not basing sc_mac_rxcfg and thus GEM_MAC_RX_CONFIG on the
default configuration. Solve this by calling gem_setladrf() after reading
in the default configuration of GEM_MAC_RX_CONFIG. This also avoids the
need to distinguish whether gem_setladrf() should enable the RX MAC again
and should be slightly more correct as we're now doing all of the RX MAC
configuration in the intended step.
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
