The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
upper layer(s).
This eliminates the if_snd queue from net80211. Yay!
This unfortunately has a few side effects:
* It breaks ALTQ to net80211 for now - sorry everyone, but fixing
parallelism and eliminating the if_snd queue is more important
than supporting this broken traffic scheduling model. :-)
* There's no VAP and IC flush methods just yet - I think I'll add
some NULL methods for now just as placeholders.
* It reduces throughput a little because now net80211 will drop packets
rather than buffer them if the driver doesn't do its own buffering.
This will be addressed in the future as I implement per-node software
queues.
Tested:
* ath(4) and iwn(4) in STA operation
This patchset implements a new TX lock, covering both the per-VAP (and
thus per-node) TX locking and the serialisation through to the underlying
physical device.
This implements the hard requirement that frames to the underlying physical
device are scheduled to the underlying device in the same order that they
are processed at the VAP layer. This includes adding extra encapsulation
state (such as sequence numbers and CCMP IV numbers.) Any order mismatch
here will result in dropped packets at the receiver.
There are multiple transmit contexts from the upper protocol layers as well
as the "raw" interface via the management and BPF transmit paths.
All of these need to be correctly serialised or bad behaviour will result
under load.
The specifics:
* add a new TX IC lock - it will eventually just be used for serialisation
to the underlying physical device but for now it's used for both the
VAP encapsulation/serialisation and the physical device dispatch.
This lock is specifically non-recursive.
* Methodize the parent transmit, vap transmit and ic_raw_xmit function
pointers; use lock assertions in the parent/vap transmit routines.
* Add a lock assertion in ieee80211_encap() - the TX lock must be held
here to guarantee sensible behaviour.
* Refactor out the packet sending code from ieee80211_start() - now
ieee80211_start() is just a loop over the ifnet queue and it dispatches
each VAP packet send through ieee80211_start_pkt().
Yes, I will likely rename ieee80211_start_pkt() to something that
better reflects its status as a VAP packet transmit path. More on
that later.
* Add locking around the management and BAR TX sending - to ensure that
encapsulation and TX are done hand-in-hand.
* Add locking in the mesh code - again, to ensure that encapsulation
and mesh transmit are done hand-in-hand.
* Add locking around the power save queue and ageq handling, when
dispatching to the parent interface.
* Add locking around the WDS handoff.
* Add a note in the mesh dispatch code that the TX path needs to be
re-thought-out - right now it's doing a direct parent device transmit
rather than going via the vap layer. It may "work", but it's likely
incorrect (as it bypasses any possible per-node power save and
aggregation handling.)
Why not a per-VAP or per-node lock?
Because in order to ensure per-VAP ordering, we'd have to hold the
VAP lock across parent->if_transmit(). There are a few problems
with this:
* There's some state being setup during each driver transmit - specifically,
the encryption encap / CCMP IV setup. That should eventually be dragged
back into the encapsulation phase but for now it lives in the driver TX path.
This should be locked.
* Two drivers (ath, iwn) re-use the node->ni_txseqs array in order to
allocate sequence numbers when doing transmit aggregation. This should
also be locked.
* Drivers may have multiple frames queued already - so when one calls
if_transmit(), it may end up dispatching multiple frames for different
VAPs/nodes, each needing a different lock when handling that particular
end destination.
So to be "correct" locking-wise, we'd end up needing to grab a VAP or
node lock inside the driver TX path when setting up crypto / AMPDU sequence
numbers, and we may already _have_ a TX lock held - mostly for the same
destination vap/node, but sometimes it'll be for others. That could lead
to LORs and thus deadlocks.
So for now, I'm sticking with an IC TX lock. It has the advantage of
papering over the above and it also has the added advantage that I can
assert that it's being held when doing a parent device transmit.
I'll look at splitting the locks out a bit more later on.
General outstanding net80211 TX path issues / TODO:
* Look into separating out the VAP serialisation and the IC handoff.
It's going to be tricky as parent->if_transmit() doesn't give me the
opportunity to split queuing from driver dispatch. See above.
* Work with monthadar to fix up the mesh transmit path so it doesn't go via
the parent interface when retransmitting frames.
* Push the encryption handling back into the driver, if it's at all
architectually sane to do so. I know it's possible - it's what mac80211
in Linux does.
* Make ieee80211_raw_xmit() queue a frame into VAP or parent queue rather
than doing a short-cut direct into the driver. There are QoS issues
here - you do want your management frames to be encapsulated and pushed
onto the stack sooner than the (large, bursty) amount of data frames
that are queued. But there has to be a saner way to do this.
* Fragments are still broken - drivers need to be upgraded to an if_transmit()
implementation and then fragmentation handling needs to be properly fixed.
Tested:
* STA - AR5416, AR9280, Intel 5300 abgn wifi
* Hostap - AR5416, AR9160, AR9280
* Mesh - some testing by monthadar@, more to come.
If the data frame transmission failures, it may have a node reference
that needs cleaning up.
If the frame is marked as M_ENCAP then it should treat recvif as a node
reference and clear it.
Now - since the mbuf has been freed by calling if_transmit() (even on
failure), the mbuf has to be treated as invalid. Hence why the ifp is
used.
This turns ieee80211_node_pwrsave(), ieee80211_sta_pwrsave() and
ieee80211_recv_pspoll() into methods.
The intent is to let drivers override these and tie into the power save
management pathway.
For ath(4), this is the beginning of forcing a node software queue to
stop and start as needed, as well as supporting "leaking" single frames
from the software queue to the hardware.
Right now, ieee80211_recv_pspoll() will attempt to transmit a single frame
to the hardware (whether it be a data frame on the power-save queue or
a NULL data frame) but the driver may have hardware/software queued frames
queued up. This initial work is an attempt at providing the hooks required
to implement correct behaviour.
Allowing ieee80211_node_pwrsave() to be overridden allows the ath(4)
driver to pause and unpause the entire software queue for a given node.
It doesn't make sense to transmit anything whilst the node is asleep.
Please note that there are other corner cases to correctly handle -
specifically, setting the MORE data bit correctly on frames to a station,
as well as keeping the TIM updated. Those particular issues can be
addressed later.
* Call it before sending probe responses, so the ACL code has the
chance to reject sending them.
* Pass the whole frame to the ACL code now, rather than just the
destination MAC - that way the ACL module can look at the frame
contents to determine what the response should be.
This is part of some uncommitted work to support band steering.
Sponsored by: Hobnob, Inc.
handling.
The current sequence number code does a few things incorrectly:
* It didn't try eliminating duplications from HT nodes. I guess it's assumed
that out of order / retransmission handling would be handled by the AMPDU RX
routines. If a HT node isn't doing AMPDU RX, then retransmissions need to
be eliminated. Since most of my debugging is based on this (as AMPDU TX
software packet aggregation isn't yet handled), handle this corner case.
* When a sequence number of 4095 was received, any subsequent sequence number
is going to be (by definition) less than 4095. So if the following sequence
number (0) doesn't initially occur and the retransmit is received, it's
incorrectly eliminated by the IEEE80211_FC1_RETRY && SEQ_LEQ() check.
Try to handle this better.
This almost completely eliminates out of order TCP statistics showing up during
iperf testing for the 11a, 11g and non-aggregate 11n AMPDU RX case. The only
other packet loss conditions leading to this are due to baseband resets or
heavy interference.
clean up parts of the *_recv_mgmt() functions.
- make sure appropriate counters are bumped and debug messages are printed
- order the unhandled subtypes by value and add a few missing ones
- fix some whitespace nits
- remove duplicate code in adhoc_recv_mgmt()
- remove a useless comment, probably left in while c&p
iv_recv_mgmt(). iv_recv_mgmt() will generate management frame responses
and pass them to bpf before the management frame that triggered the
response.
PR: 144323
Submitted by: Alexander Egorenkov <egorenar at gmail.com>
MFC after: 2 weeks
Sponsored by: iXsystems, inc.
o add a new facility for components to register send+recv handlers
o ieee80211_send_action and ieee80211_recv_action now use the registered
handlers to dispatch operations
o rev ieee80211_send_action api to enable passing arbitrary data
o rev ieee80211_recv_action api to pass the 802.11 frame header as it may
be difficult to locate
o update existing IEEE80211_ACTION_CAT_BA and IEEE80211_ACTION_CAT_HT handling
o update mwl for api rev
Reviewed by: rpaulo
Approved by: re (kensmith)
characteristics force the stations to re-associate so protocol state
is re-initialized. Note that for 11h/DFS this is irrelevant as channel
changes are never cross-band.
Reviewed by: ctlaw
o track # bpf taps on monitor mode vaps instead of # monitor mode vaps
o spam monitor mode taps on tx/rx
o fix ieee80211_radiotap_rx_all to dispatch frames only if the vap is up
o while here print radiotap (and superg) state in show com
o do not attach DLT_IEEE802_11_RADIO unless both tx and rx headers are
present; this is assumed in the capture code paths
o verify the above with asserts in ieee80211_radiotap_{rx,tx}
o add missing checks for active taps before calling ieee80211_radiotap_rx
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
indicates if an association id is required before outbound traffic
is permitted. This cleans up the previous change that broke mcast
traffic "to the stack" in ap mode as a side effect.
Reviewed by: sephe, thompsa, weongyo
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
o change ieee80211_parse_htcap and ieee80211_parse_htinfo to save only
internal state obtained from the ie's; no dynamic state such as
ni_chw is altered
o add ieee80211_ht_updateparams to parse ht cap+info ie's and update
dynamic node state
o change ieee80211_ht_node_init to not take an htcap ie that is parsed;
instead have the caller make a separate call as one caller wants to
parse the ie while another wants to parse both cap+info ie's and
update state so can better do this with ieee80211_ht_updateparams
These changes fix sta mode state handling where the node's channel
width was shifted to ht20/ht40 prematurely.
For receive:
o explicitly tag rx frames w/ M_AMPDU instead of passing frames through
the reorder processing according to the node having HT and the frame
being QoS data
o relax ieee80211_ampdu_reorder asserts to allow any frame to be passed
in, unsuitable frames are returned to the caller for normal processing;
this permits drivers that cannot inspect the PLCP to mark all data
frames as potential ampdu candidates with only a small penalty
o add M_AMPDU_MPDU to identify frames resubmitted from the reorder q
For transmit:
o tag aggregation candidates with M_AMPDU_MPDU
o fix the QoS ack policy set in ampdu subframes; we only support immediate
BA streams which should be marked for "normal ack" to get implicit block
ack behaviour; interestingly certain vendor parts BA'd frames with the
11e BA ack policy set
o do not assign a sequence # to aggregation candidates; this must be done
when frames are submitted for transmit (NB: this can/will be handled
better when aggregation is pulled up to net80211)
turns out some devices do this and since we otherwise validate the station
is associated and don't use the aid for anything being lenient here allows
them to function
Submitted by: Chris Zimmermann
MFC after: 2 weeks
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
