sys/cam/scsi/scsi_all.h:
Add the SCSI Solid State Media log page (0x11) structure
definition. This gives the percentage used (in terms of
lifetime flash wear) of an SSD.
MFC after: 3 days
Sponsored by: Spectra Logic
From user report, the errors are seen:
error 1
error 1
gptzfsboot: error 1 lba 4294967288
gptzfsboot: error 1 lba 1
gptzfsboot: no ZFS pools located, can't boot
The first two errors above are from issuing INT13 EAX=0x4800, meaning we
need to check if EDD is available and use EAX=0x800 if not.
For an workaround I'm using the similar idea as in biosdisk.c - first probe
ah=8h, then check if we have EDD.
Note we would like to see the correct disk size info, but we *may*
get away with anything >64MB, so we could at least test 2 zfs pool labels
on whole disk setup and not to freak out the INT13 interface.
If we get away with initial disk probing, then we have partition sizes from
the partition table and we should be able to complete the disk probing.
Note: this update does not provide full fix to all errors, but we get
the drvsize() errors removed.
Reported by: Michael W. Lucas
Reviewed by: julian
Differential Revision: https://reviews.freebsd.org/D10591
Extended attributes and their particular implementation in linux are
different from FreeBSD so in this case we have started diverging from
the UFS EA implementation, which would be the natural reference.
Depending on future progress implementing ACLs this approach may change
but for now bring to the tree an implementation that is consistent and
can be tested.
Submitted by: Fedor Uporov
Differential Revision: https://reviews.freebsd.org/D10460
After FreeBSD SVN revision 236814, the pass(4) driver changed from
only doing error recovery when the CAM_PASS_ERR_RECOVER flag was
set on a CCB to sometimes doing error recovery if the passed in
retry count was non-zero.
Error recovery would happen if two conditions were met:
1. The error recovery action was simply a retry. (Which is most
cases.)
2. The retry_count is non-zero. (Which happened a lot because of
cut-and-pasted code.)
This explains a bug I noticed in with camcontrol:
# camcontrol tur da34 -v
Unit is ready
# camcontrol reset da34
Reset of 1:172:0 was successful
At this point, there should be a Unit Attention:
# camcontrol tur da34 -v
Unit is ready
No Unit Attention.
Try it again:
# camcontrol reset da34
Reset of 1:172:0 was successful
Now set the retry_count to 0 for the TUR:
# camcontrol tur da34 -v -C 0
Unit is not ready
(pass42:mps1:0:172:0): TEST UNIT READY. CDB: 00 00 00 00 00 00
(pass42:mps1:0:172:0): CAM status: SCSI Status Error
(pass42:mps1:0:172:0): SCSI status: Check Condition
(pass42:mps1:0:172:0): SCSI sense: UNIT ATTENTION asc:29,2 (SCSI bus reset occurred)
(pass42:mps1:0:172:0): Field Replaceable Unit: 2
There is the unit attention. camcontrol(8) has a default
retry_count of 1, in case someone sets the -E flag without
setting -C.
The CAM_PASS_ERR_RECOVER behavior was only broken with the
CAMIOCOMMAND ioctl, which is the synchronous pass(4) API. It has
worked as intended (error recovery is only done when the flag
is set) in the asynchronous API (CAMIOQUEUE ioctl).
sys/cam/scsi/scsi_pass.c:
In passsendccb(), when calling cam_periph_runccb(), only
specify the error routine when CAM_PASS_ERR_RECOVER is set.
share/man/man4/pass.4:
Document that CAM_PASS_ERR_RECOVER is needed to enable
error recovery.
Reported by: Terry Kennedy <TERRY@glaver.org>
PR: kern/218572
MFC after: 1 week
Sponsored by: Spectra Logic
vnet_pf_uninit() is called through vnet_deregister_sysuninit() and
linker_file_unload() when the pf module is unloaded. This is executed
after pf_unload() so we end up trying to take locks which have been
destroyed already.
Move pf_unload() to a separate SYSUNINIT() to ensure it's called after
all the vnet_pf_uninit() calls.
Differential Revision: https://reviews.freebsd.org/D10025
Add IRQ placement-only and ithread-only API variants. intr_event_bind
has been extended with sibling methods, as it has many more callsites in
existing code.
Reviewed by: kib@, adrian@ (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D10586
sys/cam/scsi/scsi_all.c:
In the asc_table, if we get a 0x20,0x02 error ("Access denied -
no access rights"), don't bother retrying. Instead, immediately
fail the command.
This is the error returned by Self Encrypting Drives (SED) when
they are locked.
MFC after: 3 days
Sponsored by: Spectra Logic
Prior to this change, the CRN (Command Reference Number) is reset on any
firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which
specifies that the CRN should only be reset in response to a LIP Reset
(LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS
actions as conditions for resetting the CRN for the associated initiator
port.
These violations manifest themselves when the HBA is removed from the
loop, or a target device is removed (especially during an outstanding
command) without power cycling. If the HBA and and the target device
determine upon re-establishing the loop that no PLOGI or PRLI is
required, and the target does not issue a LIPxy to the initiator, the
CRN for the target will have been improperly reset by the isp driver. As
a result, the target port will silently ignore all FCP commands issued
during the device probe (which will time out) preventing the device from
attaching.
This change corrects thie CRN reset behavior in response to loop state
changes, also introduces CRN resets for the above mentioned ELS actions
as encountered through async PDB change events.
This change also adds cleanup of outstanding commands in isp_loop_dead()
that was previously missing.
sys/dev/isp/isp.c
Add the last login state to debug output when syncing the pdb
sys/dev/isp/isp_freebsd.c
Replace binary statement setting aborted ccb status in
isp_watchdog() with the XS_SETERR macro used elsewhere
In isp_loop_dead(), abort or complete pending commands as done
in isp_watchdog()
In isp_async(), segregate the ISPASYNC_LOOP_RESET action from
ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP
fallthroughs, and only reset the CRN in the RESET case. Also add
checks to handle false LOOP RESET actions that do not have a
proper associated LIP primitive, and log the primitive in the
debug messages
In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and
only reset the CRN in the DEV_CHANGED action
In isp_async(), when processing an ISPASYNC_CHANGE_PDB status,
reset CRN(s) for the associated nphdl (or all ports) if the
change reason is some form of ELS login/logout. Also remove
assignment to fc since it is not used in the scope
sys/dev/isp/ispmbox.h
Add macro definition for the global N-Port handle, and correct a
macro typo 'PDB24XX_AE_PRLI_DONJE'
sys/dev/isp/ispvar.h
Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for
more legible code when determining if an AL_PD port matches the
portid for a given struct fcparam* by value or by virtue of the
AL_PD port being 0xFF
Submitted by: Reid Linnemann
Sponsored by: Spectra Logic
MFC after: 1 week
During gmirror startup, if component mirrors are found to be dirty as is
typical after a system crash, the mirrors are synchronized to the mirror
with highest priority. However if a gmirror starts without all of its
mirrors present, for example because of some transient delays during
tasting, the remaining mirrors must be synchronized before they may become
active.
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
Before this change if_lagg was using nonsleepable rmlocks to protect its
internal state. This patch introduces another sx lock to protect code
paths that require sleeping, while still uses old rmlock to protect hot
nonsleepable data paths.
This change allows to remove taskqueue decoupling used before to change
interface addresses without holding the lock. Instead it uses sx lock to
protect direct if_ioctl() calls.
As another bonus, the new code synchronizes enabled capabilities of member
interfaces, and allows to control them with ifconfig laggX, that was
impossible before. This part should fix interoperation with if_bridge,
that may need to disable some capabilities, such as TXCSUM or LRO, to allow
bridging with noncapable interfaces.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D10514
This restores 32bit-sized accesses to vmcnt sysctls, making old
binaries like top(1), systat(8) and reboot(8) mostly functional on
newer kernel.
Reviewed by: bde
Sponsored by: The FreeBSD Foundation
At least with Tx FIFO enabled it shows me ~10% reduction of verbose boot
time with serial console at 115200 baud.
Reviewed by: marcel
MFC after: 2 weeks
The current reboot command in efi/loader/main.c is passing extra data with
ResetSystem, however, UEFI spec 2.6, page 265 does state:
"ResetData is only valid if ResetStatus is something other than EFI_SUCCESS
unless the ResetType is EfiResetPlatformSpecific where a minimum amount of
ResetData is always required."
Therefore we should use DataSize 0 and ResetData NULL - those are two last
arguments for the call.
Reviewed by: emaste
Differential Revision: https://reviews.freebsd.org/D10562
cannot access the GLOBAL2 register directly.
Despite the comment in code (which was misleading), the indirect access is
only used to read the switch CONFIG data from the scrap register and not
for the GLOBAL2 access.
Use the dsa data to define when the switch is in the Multi Chip Addressing
Mode (a even address different than zero).
While here fix a typo.
Sponsored by: Rubicon Communications, LLC (Netgate)
This patch allows the MTU stored in the hostcache to be used as an
initial value for SCTP paths. When an ICMP PTB message is received,
store the MTU in the hostcache.
MFC after: 1 week
determining the softc of the bridge in psycho_route_interrupt(). [1]
While at it, update the corresponding comment that the code in
question is also necessary for U30s in addition to E450s (a fact
that has been known for ages).
PR: 218478
Submitted by: Yoshihiko Iwama
The code specified the length of a layout as INT64_MAX instead of
UINT64_MAX. This could result in getting a layout for less than the
full file for extremely large files. Although having little practical
effect, this patch corrects this in the code.
Detected during recent testing of the pNFS server.
MFC after: 2 weeks
In exceptional circumstances, an MCA exception will trigger when the
freelist is exhausted. In such a case, no error will be logged on the list
and 'mca_count' will not be incremented.
Prior to this patch, all CPUs that received the exception would spin
forever.
With this change, the CPU that detects the error but finds the freelist
empty will proceed to panic the machine, ending the deadlock.
A follow-up to r260457.
Reported by: Ryan Libby <rlibby at gmail.com>
Reviewed by: jhb@
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D10536
It improves interoperability with if_bridge, which may need to disable
some capabilities not supported by other members. IMHO there is still
open question about LRO capability, which may need to be disabled on
physical interface.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
7740 fix for 6513 only works in hole punching case, not truncation
illumos/illumos-gate@7de35a3ed07de35a3ed0https://www.illumos.org/issues/7740
The problem is that dbuf_findbp will return ENOENT if the block it's
trying to find is beyond the end of the file. If that happens, we assume
there is no birth time, and so we lose that information when we write
out new blkptrs. We should teach dbuf_findbp to look for things that are
beyond the current end, but not beyond the absolute end of the file.
To verify, create a large file, truncate it to a short length, and then
write beyond the end. Check with zdb to make sure that there are no
holes with birth time zero (will appear as gaps).
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Paul Dagnelie <pcd@delphix.com>
