o Don't check the dummy fields.
o The entry is unused if either dp_mid is 0 or dp_sid is 0.
o The start or end cylinder cannot be 0.
o The start CHS cannot be equal to the end CHS.
Submitted by: nyan
still valid. We were checking the state of the header and
not the table.
PR: 119868
Based on a patch from: Jaakko Heinonen <jh@saunalahti.fi>
MFC after: 1 week
a little refinement, but is good enough to commit as is.
# Should look to see if I should move swab(3) into the kernel or just
# provide the unoptimized routine here.
Reviewed by: marcel@
are possibly still being created. The d_secperunit field
contains the number of sectors of the disk and not of the
slice/partition to which the disklabel applies.
Rather than reject the disklabel, we now silently adjust
the field. Existing code, like bslabel(8), does not seem
to check the label that extensively and seems to adjust
fields as a side-effect as well.
In other words, it's not that important apparently, so
gpart should not be too strict about it.
Reported by: nyan@
Reported by: Andriy Gapon <avg@icyb.net.ua>
Export the active and bootable flags as attributes in
the configuration XML and allow them to be manipulated
with the set/unset commands.
Since libdisk treats the flags as part of the partition
type, preserve behavior by keeping them included in the
configuration text.
if the probe succeeds. This guarantees that the BSD scheme
wins over the MBR scheme when MBR gets to probe first. Build-
or link-time conditions can cause schemes to end up in the
linker set in a different order. Normally BSD is before MBR
in the linker set and as such get to probe first. But typically
when the kernel gets rebuild or relinked, this can change.
that a nested partition (typically the BSD disklabel)
is not done tasting while the root file system is being
mounted. While this is rare, it's still possible.
the method for the (indent == NULL) case (i.e. the kern.geom.conftxt
sysctl). The purpose is to extend the conftxt output with scheme-
specific fields which can be used by libdisk. In particular, have
the schemes dump the xs and xt fields, which contain the backward
compatible values for class type and partition type. This allows
libdisk to work with the legacy slicers as well as with gpart and
helps/promotes migration.
SI_SUB_DRIVERS) to avoid loading schemes before all the GEOM
classes have been loaded and initialized. Otherwise we may
end up using mutexes that haven't been initialized (due to
g_retaste() posting an event).
to declaring a proper module. The module event handler is part of the
gpart core and will add the scheme to an internal list on module load
and will remove the scheme from the internal list on module unload.
This makes it possible to dynamically load and unload partitioning
schemes.
not have VTOC information about the partitions, it will be created.
This is because the VTOC information is used for the partition type
and FreeBSD's sunlabel(8) does not create nor use VTOC information.
For this purpose, new tags have been added to support FreeBSD's
partition types.
partition table is empty, check to see if we have something that
looks sufficiently like a BPB. On non-i386 machines, the boot
sector typically doesn't contain boot code; the end of the boot
sector is all zeroes. This is also where the partition table is
for MBRs.
We only check the sector size and cluster size, as that seems to
be the most reliable across implementations, BPB versions and
platforms.
only because there's a partition table where the boot sector has
boot code. Boot sectors without boot code look like a MBR for all
practical purposes. This change adds a check for the partition table
and fails the probe when it's obvously invalid. The assumption being
that the sector contains a boot sector and not a MBR.
More checks are needed to distinguish a boot secto without boot code
from a (empty) MBR.
o BSD disklabels have relative offsets. Even for the BSD in MBR slice
setup, except when the mbroffset ioctl is supported. Since we don't
support that ioctl, bsdlabel(8) expects relative offsets. So, when
reading an existing disklabel, correct for disklabels that mistakenly
have the mbroffset offsets.
o Don't take the geometry seriously, because it's untrustworthy. We do
expect the numbers to be within range. This means that the secperunit
field will not be computed from secpercyl and ncyls, but simply is
the mediasize in sectors.
o Don't enforce partitions to be aligned to track boundaries. The
default label, constructed by bsdlabel(8), puts partition a at offset
BBSIZE bytes, which commonly means sector 16.
o Disklabels can have between 8 and 20 partitions (inclusive).
o No device special file is created for the raw partition.
o Switch ia64 to use this backend.
o No support for boot code yet.
on i386 and amd64 machines. The overall process is that /boot/pmbr lives
in the PMBR (similar to /boot/mbr for MBR disks) and is responsible for
locating and loading /boot/gptboot. /boot/gptboot is similar to /boot/boot
except that it groks GPT rather than MBR + bsdlabel. Unlike /boot/boot,
/boot/gptboot lives in its own dedicated GPT partition with a new
"FreeBSD boot" type. This partition does not have a fixed size in that
/boot/pmbr will load the entire partition into the lower 640k. However,
it is limited in that it can only be 545k. That's still a lot better than
the current 7.5k limit for boot2 on MBR. gptboot mostly acts just like
boot2 in that it reads /boot.config and loads up /boot/loader. Some more
details:
- Include uuid_equal() and uuid_is_nil() in libstand.
- Add a new 'boot' command to gpt(8) which makes a GPT disk bootable using
/boot/pmbr and /boot/gptboot. Note that the disk must have some free
space for the boot partition.
- This required exposing the backend of the 'add' function as a
gpt_add_part() function to the rest of gpt(8). 'boot' uses this to
create a boot partition if needed.
- Don't cripple cgbase() in the UFS boot code for /boot/gptboot so that
it can handle a filesystem > 1.5 TB.
- /boot/gptboot has a simple loader (gptldr) that doesn't do any I/O
unlike boot1 since /boot/pmbr loads all of gptboot up front. The
C portion of gptboot (gptboot.c) has been repocopied from boot2.c.
The primary changes are to parse the GPT to find a root filesystem
and to use 64-bit disk addresses. Currently gptboot assumes that the
first UFS partition on the disk is the / filesystem, but this algorithm
will likely be improved in the future.
- Teach the biosdisk driver in /boot/loader to understand GPT tables.
GPT partitions are identified as 'disk0pX:' (e.g. disk0p2:) which is
similar to the /dev names the kernel uses (e.g. /dev/ad0p2).
- Add a new "freebsd-boot" alias to g_part() for the new boot UUID.
MFC after: 1 month
Discussed with: marcel (some things might still change, but am committing
what I have so far)
don't have it. Some partitioning schemes, as well as file systems,
operate on the geometry and without it such schemes (e.g. MBR)
and file systems (e.g. FAT) can't be created. This is useful for
memory disks.
