will intialize the the header length and re-initialize the mbuf pointer
to reference the mbuf that is allocated after moving user supplied packet
data in.
ioctl routines if we are running with !mpsafenet
- Change un-conditional Giant acquisition around ifpromisc
to occur only if we are running with !mpsafenet
With these locking bits in place, we can now remove the Giant
requirement from BPF, so drop the D_NEEDGIANT device flag.
This change removes Giant acquisitions around BPF device
handlers (read, write, ioctl etc).
MFC after: 1 month
Discussed with: rwatson
bridged, previously legitimate traffic was not passed as the bridge could not
tell that it was on a different Ethernet segment.
All non-tagged traffic is treated as vlan1 as per IEEE 802.1Q-2003
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
the value of ph_nhooks to zero, not the address. This removes
extranious calls to pfil_run_hooks (and an rw lock) from the
network stack's critical path when no pfil hooks are active.
Reviewed by: csjp
Sponsored by: Myricom Inc.
which support a 2.5Gbps mode over fiber using next page extensions during
autonegotiation. Typically only found in blade systems which also include
a Broadcom 2.5Gbps capable switch.
MFC after: 2 weeks
as to the type of the command argument: int -> u_long.
These types have different widths in the 64-bit world.
Add a note to UPDATING because the change breaks KBI
on 64-bit platforms.
Discussed on: -net, -current
Reviewed by: bms, ru
- In rt_check() remove the senderr() macro and the "bad" label. They
used to simplify code, but now aren't.
- Remove extra RT_LOCK_ASSERT() in rt_setgate(). The RT_REMREF macro
does this.
- In rtfree() convert panics to KASSERTs.
- Strict the routing API: rtfree() should be called only in a case
when we are completely sure we've got the last reference on the
rtentry. In all other cases RTFREE_LOCKED() macro should be used.
If the reference isn't the last one spit out a warning printf.
Correct the only(?) case for this in rt_check().
- Fix typos in comments.
of each port and any further packets are blocked, when the all the marker frames
have been returned to us from the remote network device then we can be sure
that all interface queues are empty.
This is needed when a port is added or removed from the aggregation since it
will affect the hash based distribution, if the queues are not empty then a
packet from an existing connection may be placed on a different interface and
arrive out of order. This was previously achieved by suppressing transmission for
1 second, now that there is an active feedback this timeout as been increased
to 3 seconds and used as a fallback.
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
tolerance. This driver allows aggregation of multiple network interfaces as
one virtual interface using a number of different protocols/algorithms.
failover - Sends traffic through the secondary port if the master becomes
inactive.
fec - Supports Cisco Fast EtherChannel.
lacp - Supports the IEEE 802.3ad Link Aggregation Control Protocol
(LACP) and the Marker Protocol.
loadbalance - Static loadbalancing using an outgoing hash.
roundrobin - Distributes outgoing traffic using a round-robin scheduler
through all active ports.
This code was obtained from OpenBSD and this also includes 802.3ad LACP support
from agr(4) in NetBSD.
