time in the cases where it really sends the drive out to lunch, but it also
allows us to catch very wierd edge cases of strange drives that might take
a very long time (emulated disk drives over a network, e.g.).
quirk regarding the C- series makes me suspect that all Olympus models have
the same quirks, but I cannot prove it.
Submitted by: Bernd Walter <ticso@cicely8.cicely.de>
attempts to set buffered mode was printing out "unable to set buffered
mode" no matter what. Oops.
Spotted by: Joerg Wunsch <joerg_wunsch@uriah.heep.sax.de>
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Clear residual counts after a successful samount (the user doesn't
care that we got an N-kbyte residual on our test read).
Change a lot of error handling code.
1. If we end up in saerror, check more carefully about the kind of
error. If it is a CAM_SCSI_STATUS_ERROR and it is a read/write
command, we'll be handling this in saerror. If it isn't a read/write
command, check to see whether this is just an EOM/EOP check condition-
if it is, just set residual and return normally. A residual and
then a NO SENSE check condiftion with the ASC of 0 and ASCQ of
between 1 and 4 are normal 'signifying' events, not errors per se,
and we shouldn't give the command to cam_periph_error to do something
relatively unpredictable with.
2. If we get a Bus Reset, had a BDR sent, or get the cam status of
CAM_REQUEUE_REQ, check the retry count on the command. The default
error handler, cam_periph_error, doesn't honor retry count in these
cases. This may change in the future, but for now, make sure we
set EIO and return without calling cam_periph_error if the retry
count for the command with an error is zero.
3. Clean up the pending error case goop and handle cases more
sensibly.
The rules are:
If command was a Write:
If we got a SSD_KEY_VOLUME_OVERFLOW, the resid is
propagated and we set ENOSPC as the error.
Else if we got an EOM condition- just mark EOM pending.
And set a residual of zero. For the longest time I was just
propagating residual from the sense data- but my tape
comparison tests were always failing because all drives I
tested with actually *do* write the data anyway- the EOM
(early warning) condition occurred *prior* to all of the
data going out to media- that is, it was still buffered by
the drive. This case is described in SCSI-2, 10.2.14,
paragraph #d for the meaning of 'information field'. A
better fix for this would be to issue a WFM command of zero
to cause the drive to flush any buffered data, but this
would require a fairly extensive rewrite.
Else if the command was a READ:
If we got a SSD_KEY_BLANK_CHECK-
If we have a One Filemark EOT model- mark EOM as pending,
otherwise set EIO as the erorr.
Else if we found a Filemark-
If we're in Fixed Block mode- mark EOF pending.
If we had an ILI (Incorrect Length Indicator)-
If the residual is less than zero, whine about tape record
being too big for user's buffer, otherwise if we were in
Fixed Block mode, mark EIO as pending.
All 'pending' conditions mean that the command in question completes
without error indication. It had succeeded, but a signifying event
occurred during its execution which will apply to the *next* command
that would be exexcuted. Except for the one EOM case above, we always
propagate residual.
Now, way back in sastart- if we notice any of the PENDING bits set,
we don't run the command we've just pulled off the wait queue. Instead,
we then figure out it's disposition based upon a previous command's
association with a signifying event.
If SA_FLAG_EOM_PENDING is set, we don't set an error. We just complete
the command with residual set to the request count (not data moved,
but no error). We continue on.
If SA_FLAG_EOF_PENDING- if we have this, it's only because we're in
Fixed Block mode- in which case we traverse all waiting buffers (which
we can get in fixed block mode because physio has split things up) and
mark them all as no error, but no data moved and complete them.
If SA_FLAG_EIO_PENDING, just mark the buffer with an EIO error
and complete it.
Then we clear all of the pending state bits- we're done.
MFC after: 4 weeks
Handle both old and new TARGIOALLOCUNIT/TARGIOFREEUNIT cases- the new
one allows us to specify inquiry data we want to use.
Handle more of the CAM_DIS_DISCONNECT case.
Move TARGCTLIOALLOCUNIT to OTARGCTLIOALLOCUNIT, TARGCTLIOFREEUNIT
to OTARGCTLIOFREEUNIT and redefine old associated structure to be
old_ioc_alloc_unit- deprecation but preservation of binaries.
Add new structure for same- but this one contains a pointer to
user defined INQUIRY data so you can define what the target
device looks like to the outside world.
1. If we get frozen, unfreeze for disable disconnects.
2. Put CAM_DIS_DISCONNECT commands at the head of the work queue
(we have a target still connected and we can't run anything else
until this command completes).
If we had an error sending the last CTIO, unfreeze the queue anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
This is useful if you want to dynamically move into a Fibre Channel
or Multi-initiator environment that happens to be particularly noisy
and ugly that requires a lot of retries (with shorter I/O timeouts)
for commands destried by LIPs or Bus Resets.
Reviewed by: deafening silence on audit && scsi on the retry counts
MFC after: 2 weeks
1. Add SA_IO_TIMEOUT as an option (4 minutes default) to cover reads,
writes, wfm, test unit ready.
2. Add internal SCSIOP_TIMEOUT (e.g., for mode sense) at 1 minute. This
should not require an option, but is cleaner to parameterize.
MFC after: 1 week
drivers.
- change daprevent() to set CAM_RETRY_SELTO and SF_RETRY_UA when it calls
cam_periph_runccb().
- change the pt(4) driver to ignore unit attentions
- change the targ(4) driver to retry selection timeouts
- clean up a few formatting glitches in the targ(4) driver
Reviewed by: gibbs
prevent scsi_sense_desc() from deferencing a NULL pointer when a drive
happens to return one of these sense keys.
Reported by: Michael Samuel <michael@miknet.net>
With the recent changes in the CAM error handling, some problems in
the error handling of sa(4) have been uncovered. Basically, a number
of conditions that are not actually errors have been mistreated as
genuine errors. In particular:
. Trying to read in variable length mode with a mismatched blocksize
between the on-tape (virtual) blocks and the read(2) supplied buffer
size, causing an ILI SCSI condition, have caused an attempt to retry
the supposedly `errored' transfer, causing the tape to be read
continuously until it eventually hit EOM. Since by default any
simple mt(1) operation does an initial test read, an `mt stat' was
sufficient to trigger this bug.
Note that it's Justin's opinion that treating a NO SENSE as an EIO
is another bug in CAM. I feel not authorized to fix cam_periph.c
without another confirmation that i'm on the right track, however.
. Hitting a filemark caused the read(2) syscall to return EIO, instead
of returning a `short read'. Note that the current fix only solves
this problem in variable length mode. Fixed length mode uses a
different code path, and since i didn't grok all the intentions behind
that handling, i did not touch it (IOW: it's still broken, and you get
an EIO upon hitting a filemark).
The solution is to keep track of those conditions inside saerror(),
and upon completion to not call cam_periph_error() in that case. We
need to make sure that the device gets unfrozen if needed though (in
case of actual errors, cam_periph_error() does this on our behalf).
Not objected by: mjacob (who currently doesn't have the time to
review the patch)
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
inq_len member of the ccb_getdev structure, but we've never filled that
value in..
So we now get the length from the inquiry data returned by the drive.
(Since we will fetch as much inquiry data as the drive claims to support.)
Reviewed by: mjacob
Reported by: Andrzej Tobola <san@iem.pw.edu.pl>
o Offset and period in synch messages and width negotiation should be
done for per target not per lun. Move these from *lun_info to
*targ_info.
o Change in handling XPT_RESET_DEV and XPT_GET_TRAN_SETTINGS .
o Change CAM_* xpt_done return values.
o Busy loop did not timeout. Change this to timeout as original NetBSD/pc98.
Reviewed by: bsd-nomads ML
not be retried. It is an indication that there was an error that was
corrected during the execution of the command. This is per ANSI SCSI2
spec.
It's possible that these should also be noted to the console (as indicative,
perhaps, of growing media defect lists in drives), but the default of
printing errors out if bootverbose in this case is probably enough.
Also, there'd been a missing ERESTART for that clause anyway.
2. If you have an ABORTED COMMAND, it's almost invariably a SCSI parity
error. You should never be silent about these since users should do something
about this if it occurs (moving that power cord *away* from the SCSI cable is
always a good first start). This should print irrespective of bootverbose
because it's an actual real error even if we retry a transmission.
Reviewed by: audit@freebsd.org, gibbs@freebsd.org
we *really* are.
It should be noted that there is a degenerate case where soft tape
location will be lost (not causing a frozen state- but causing
the loss of reporting fileno/blockno)- that's where you backspace
over a filemark- you stop backspacing as soon as you cross the
filemark, but you have no idea what the record number now is because
you have no idea how many records you are into the file you just
backed into. Such is life.
While I'm at it, also pick up residuals from writing filemarks.
PR: 24222
only CCB type but also extra flags- one of which can be "position
updated".
In other changes: Add in a SA_QUIRK_NO_CPAGE quirk so that it's possible
to avoid using a (broken) device's implementation of he DEVICE COMPRESSION
page.
Also do a couple of printout cleanups.
As per some discussion on FreeBSD-scsi, skip doing tape flushing
if we're reading tape logical block location (MTIOCRDSPOS).
MS will be treated as having this quirk. In the event that we falsely
identify one that doesn't need it, no harm will be done. Ken
suggested that we make this more generic since there may be more
needed in the future.
Reported by: TERAMOTO Masahiro <teramoto@comm.eng.osaka-u.ac.jp>
PR: kern/23378
Reviewed by: ken
field in CDB' error when attempting to start a caddy-type CD drive,
since those drives apparently in general refuse to load a medium. Since
we never advertised the feature to load the medium upon calling
cdstartunit() (i. e. upon receipt of a CDIOCSTART ioctl command), nobody
should have relied on it. Besides, nobody noticed so far at all that
this command is failing for caddy-type drives... Only few applications
seem to use it at all (among them is workman, which made me notice it).
Reviewed by: ken
CDs.
With audio CDs, you can't just do a READ(10) call on most drives without
first setting the blocksize with a mode select command. The disklabel code
does a read of the first sector of the media to find a label if it exists.
This caused drives to return an error when an audio CD was in the drive,
due to the problem described above.
The solution is to read the table of contents on the CD, and only attempt
to read the disklabel if the first track is a data track.
This works on all the various CD and DVD media I have tried, but further
testing (especially with Video CDs and other mode 2 media) will be
needed to determine if this is a universal solution.
This allows writing to DVD-RAM, PD and similar drives that probe as CD
devices. Note that these are randomly writeable devices, not
sequential-only devices like CD-R drives, which are supported by cdrecord.
Add a new flag value for dsopen(), DSO_COMPATLABEL. The cd(4) driver now
uses this flag instead of the DSO_NOLABELS flag. The DSO_NOLABELS always
used a "fake" disklabel for the entire disk, provided by the caller.
With the DSO_COMPATLABEL flag, dsopen() will first search the media for a
label, and if it finds a label, it will use that label. Otherwise it will
use the fake disklabel provided by the caller. This provides backwards
compatibility, since we will still have labels for ISO9660 media.
It also provides new functionality, since you can now have a regular BSD
disklabel on read-only media, or on writeable media (e.g. DVD-RAM).
Bruce and I both think that we should eventually (in a few years) get
away from using disklabels for ISO9660 media, and just use the whole disk
device (/dev/cd0). At that point disklabel handling in the cd(4) driver
could follow the "normal" model, as used in the da(4) driver.
Also, clean up the path in a couple of places in cdregister(). (Thanks to
Nick Hibma for catching that bug.)
Reviewed by: bde
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
for the Quantum "MAVERICK 540S" and "LPS525S".
Also, add common string variables, since we seem to have a few Quantum and
Micropolis drives in here.
Fix the 'quantum' variable usage in scsi_all.c that likely got broken when
someone staticized things in cam_xpt.c. (That particular problem would
cause Quantum Fireball ST drives to not get spun up if they were not
already spinning.)
Submitted by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
to be obeying the original spec as to what the numeric value means.
Temperature flags are unaffected- these are still the 'pseudo-thermometers'
and overtemp/undertemp warnings will be caught and translated to SES objects
here.
PR: 20475
related patches. These include:
* Mode page editting can be scripted. This involves two
things: first, if stdin is not a tty, changes are read from
stdin rather than invoking $EDITOR. Second, and more
importantly, not all modepage entries must be included in the
change set. This means that camcontrol can now gracefully handle
more intrusive editting from the $EDITOR, including removal or
rearrangement of lines. It also means that you can do stuff
like:
# echo "WCE: 1" | camcontrol modepage da3 -m 8 -e
# newfs /dev/da3
# echo "WCE: 0" | camcontrol modepage da3 -m 8 -e
* Range-checking on user-supplied input values. modeedit.c now
uses the field width specifiers to determine the maximum
allowable value for a field. If the user enters a value larger
than the maximum, it clips the value to the max and warns the
user. This also involved patching cam_cmdparse.c to be more
consistent with regards to the "count" parameter to arg_put
(previously is was the length of strings and 1 for all integral
types). The cam_cdbparse(3) man page was also updated to reflect
the revised semantics.
* In the process, I removed the 64 entry limit on mode pages (not
that we were even close to hitting that limit). This was a nice
side-effect of the other changes.
* Technically, the new mode editting functionality allows editting
of character array entries in mode pages (type 'c' or 'z'),
however since buff_encode doesn't grok them it is currently
useless.
* Camcontrol gained two new options related to mode pages: -l and
-b. The former lists all available mode pages for a given
device. The latter forces mode page display in binary format
(the default when no mode page definition was found in
scsi_modes).
* Added support for mode page names to scsi_modes. Allows names to
be displayed alongside mode numbers in the mode page
listing. Updated scsi_modes to use the new functionality. This
also adds the semicolon into the scsi_modes syntax as an
optional mode page definition terminator. This is needed to name
pages without providing a page format definition.
* Updated scsi_all.h to include a structure describing mode page
headers.
* Added $FreeBSD$ line to scsi_modes.
Inspired by: dwhite
Reviewed by: ken
Clean up the comments related to the high speed
sync rate table for SPI.
scsi_message.h:
Bring in some SCSI3 message terminology. All SCSI2 names
are still preserved for backwards compatibility.
CAM_TAG_ACTION_VALID and CAM_DIR_MASK). Remove redundant
CAM_DEBUG line. Spiff up CAM_DEBUG printout for commands
and move the printout up to the top where we can see it,
even for the pending_ua/pending_ca cass. Add missing
newline in a CAM_DEBUG.
to splx(s) if cam_extend_get fails and we return ENXIO, reset ccb flags
when we push ATIOs back to the SIM, do some data increment fixes, set
priority of command based on whether CAM_DIS_DISCONNECT is set and related
changes).
Add in some more CAM_DEBUG_PERIPH debug statements and also add in support
for TARGIODEBUG which then will enable or disable CAM_DEBUG_PERIPH tracing
for an instance.
CAPACITY operation. SCSI-3 mandates this to be 2048, but some older
drives like my old Plasmon CD-R report weird numbers between 2048 and
up to 2352 bytes depending on the mode of the last track etc. This in
turn confuses stuff like the slice code since it refuses to work with
devices that do not have a blocksize which is a multiple of 512 bytes.
Reviewed by: ken
libcam/Makefile: Add scsi_da.c to libcam for the new
scsi_format_unit() function.
camcontrol.8: Update the man page for the new format
functionality, and take out the examples section
describing how to do it with 'camcontrol cmd'.
camcontrol.c: New format functionality. Note that unlike the
rest of the camcontrol subcommands, this one is
interactive by default. Because of the potential
destructiveness of the format command, I thought
it necessary to get confirmation from the user
before spamming a disk. You can disable the
interactive behavior, and the status meter with
command line arguments.
scsi_da.c: Add the new scsi_format_unit() cdb building
function and use #ifdef _KERNEL to make this file
compile in both the kernel and userland. The
format unit function is currently only defined in
the non-kernel case, because nothing in the kernel
is using it. If that changes, it should be
un-ifdefed and compiled in both cases.
scsi_da.h: New function declaration, CDB structure and format
data structures.
Thanks to Nick Hibma for providing some valuable input on these changes.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
Add a SA_QUIRK_NO_MODESEL type and use it for the OnStream real SCSI
device (not the broken one). This one is still broken in that it can't
be set to the same fixed block size it reports [ unflattering comments
about this company elided ].
If we're unable to set buffered mode on, complain, but drive on. It's
not a fatal error to not be in buffered mode.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
- Mike Smith discovered a panic in the changer probe code if the probe
command (mode sense) fails. So we need to release the CCB used in the
probe before we unlock the peripheral. (i.e. the same fix mjacob put in
the CD and DA drivers)
- A newline was missing in a warning message. (PR kern/17512)
PR: kern/17512
Submitted by: Louis Mamakos <louie@uu.net> (newline fix)
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
an HBA. Garbage in this field confuses the driver in targdone().
o When completing a CCB on behalf of a user process, we need to
*de-queue* the ccb from our pending ccb list, not queue it again.
o All continue target I/O operations need to have a timeout set.
We use 5 seconds throughout this driver.
o Remove some logging printfs.
o During abort processing, remove ccbs that are on the pending queue
from the pending queue, not the work queue.
256 bytes) caused it to break on many devices.
The SCSI spec says that for commands with 8-bit length fields, a value of 0
means 256 bytes. As it turns out, many devices don't deal with that
properly. Some interpret the 0 as 0, and return no data. Others return
more than 256 bytes of data, and cause an overrun.
The fix is to tell the device we've only allocated SHORT_INQUIRY_LENGTH (36
bytes) of inquiry data, instead of sizeof(struct scsi_inquiry_data).
camcontrol.c: Change inq_len in the call to scsi_inquiry() to
SHORT_INQUIRY_LENGTH, and add a long comment
explaining the reason for the change.
scsi_all.h: Add a comment above the definitinon of
SHORT_INQUIRY_LENGTH alerting people that it is
both the initial probe inquiry length, and the
minimum amount of data needed for scsi_print_inquiry()
to function.
scsi_all.c: Add a comment about SHORT_INQUIRY_LENGTH being the
minimum amount of data needed for
scsi_print_inquiry() to function.
Reviewed by: gibbs
Approved by: jkh
Reported by: "John W. DeBoskey" <jwd@unx.sas.com>
that there's sense to send with status (if the SIM does it), and
then clear any pending contingent allegiance state for this initiator
if the SIM actually did send the sense data.
Widen MAX_INITITATORS to 256- that's still not quite right, but will
accomodate the widest Fibre Channel support in FreeBSD now.
Obtained from:(partially) gibbs@freebsd.org
full size. Define a SHORT_INQUIRY_LENGTH for use during initial
probing (covers the size used previously). Define some SPC-2 related
fields (and define the revision code for SPC-2) which includes some
further SPI-3 defines. Don't go all the way (256 bytes) for the structure-
stop 4 bytes short- because we haven't auditted the source base to find
any u_int8_t potential overflow issues. Add RBC (single byte device)
and OCR (Optical Character Reader) device type codes.
Approved by JKH.
Reviewed by: gibbs@freebsd.org, ken@freebsd.org
to be more platform independent. Add a ses_hlptxt structure definition
and retrieval ioctl for when we are able to retrieve object help text
SES Objects can have up to 64 KBytes of associated 'help' text- the
Sun A5000 uses this, for example, to give physical location information
(e.g., 'left power supply').
to be created at init time. The unit devices are created at
ctor when new instances are created and bound and destroyed
when that instance is closed. As such, there is just s single
static control dev_t for this driver (the per-unit dev_t's are
still in the softc).
When we have decommissionable periph drivers, a destroy_device
on the control device will have to called.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
second LUN to show up.
mjacob's change (which is correct) in rev 1.21 of cam_periph.c to elminiate
infinite retries of the SCSI busy status bit seems to have broken probing
of Pioneer changers that aren't already quirked.
The right way to fix this is probably to change things around so we can
guarantee 100% sequential probing of LUN-based changers even if they aren't
quirked. This should fix things for now, though.
The same goes for CD drivers and tape drivers. In systems with mixed IDE
and SCSI, devices in the same priority class will be sorted in attach
order.
Also, the 'CCD' priority is now the 'ARRAY' priority, and a number of
drivers have been modified to use that priority.
This includes the necessary changes to all drivers, except the ATA drivers.
Soren will modify those separately.
This does not include and does not require any change in the devstat
version number, since no known userland applications use the priority
enumerations.
Reviewed by: msmith, sos, phk, jlemon, mjacob, bde
in samount. Make things a lot quieter in samount (and other places). Fix
ridiculous and not so ridiculous bugs in compression related code in both
sagetparams and sasetparams.
saprevent when we're doing an OFFLINE ioctl- saprevent
won't unlock the door, which then causes the unload to
fail on some units.
If we've already unloaded the tape, don't try and rewind and
unload in saclose. This is a slightly riskier change because
we're now going to depend on SA_FLAG_TAPE_MOUNTED to say whether
we've really unloaded the tape. This involved changing the
setting in sadone for tape errors to SA_FLAG_TAPE_FROZEN (which
is more accurate anyway-if you get an EIO you've probably lost
tape position anyway) where it used to just clear the mounted
flag.
Merge the contents (less some trivial bordering the silly comments)
of <vm/vm_prot.h> and <vm/vm_inherit.h> into <vm/vm.h>. This puts
the #defines for the vm_inherit_t and vm_prot_t types next to their
typedefs.
This paves the road for the commit to follow shortly: change
useracc() to use VM_PROT_{READ|WRITE} rather than B_{READ|WRITE}
as argument.
and add a config option that allows one to default to 1FM@EOD for tapes
otherwise unquirked or unknown as to which to prefer. Note that tcopy
will be broken for these tapes until tcopy is fixed.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
- increase the default timeout from 10 seconds to 60 seconds
- add a new kernel option, SCSI_PT_DEFAULT_TIMEOUT, that lets users specify
the default timeout for the pt driver to use
- add two new ioctls, one to get the timeout for a given pt device, the
other to set the timeout for a given pt device. The idea is that
userland applications using the device can set the timeout to suit their
purposes. The ioctls are defined in a new header file, sys/ptio.h
PR: 10266
Reviewed by: gibbs, joerg
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
Handle errors reported through immediate notify ccbs. This includes
bus resets, BDR messages, and abort messages.
Properly setup CA conditions for errors such as uncorectable parity
in data phases, reselection failure, and IDE message received.
Add a mechanism for stalling the queue of transactions to a particular
initiator while a CA is in progress. Since we don't yet support
tagged I/O, this is largely just for show right now.
Properly bzero our softc at init time (oops).
Add more documentation on what all of the queues in our softc do.
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
zero traps. I actually can't believe that this compiler is *sooooo* stupid
that it did a divide when there was 1024L*1024L instead of a right shift by
20. When we get quad type modifiers in kernel printf we can change to this
too (to avoid overflow on > terabyte disk sizes).
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
code in all initiator type peripheral drivers.
scsi_target.c:
Release ATIO structures that wind up in the 'unkown command queue'
for consumption by our userland counterpart, back to the controller
when the exception for that command is cleared.
SUPPORTED). Add a SA_FLAG_TAPE_FROZEN for (see below).
Add a queue_count field to softc.
Add HP T20* Travan-5 like tape device as a FIXED/512 type device.
Works for me. Add TANDBERG SLR5 as a variable SA_QUIRK_1FM device.
Change VIPER 2525 to 1024 byte blocksize. It's possible other
drives should change too, but see below..
Change argument to sagetparams to be pointer to a sa_comp_t union-
this can be either a DATA COMPRESSION or a DEVICE CONFIGURATION
page. In general compression now tries to use the DATA COMPRESSION
page and if that fails tries the DEVICE CONFIGURATION page.
Change close routine to not rewind tape if there's a failure in either
writing filemarks or in backing over one of two filemarks for a 2FM
at EOT tape- instead mark the tape as 'frozen' and print a message
saying that either an OFFLINE or REWIND or an MTEOM command is needed
to clear this state (all bring certainty back to tape position). Fix
sastrategy to not allow I/O to a frozen tape.
Add MTIOCGETEOTMODEL/MTIOCSETEOTMODEL ioctls that get and set the EOT
model for a tape drive (you can now dynamically change whether it's
a 2 FM @ EOT or 1FM at EOT tape device). This ought to give folks
something to handle the QIC drives we don't know about. Correctly propagate
record of compression algorithm back. Clear FROZEN flag for EOM, REWIND
and OFFLINE (and RETENSION and ERASE) cases.
Fix an egregious bug in sadone that had left the device queue frozen
for deferred (for fixed mode case) errors.
Add comment in samount about how useless the test unit ready is for
invalidating a mount (this has to be fixed later).
Fix residual calculation (per Eivind) in saerror so that negative values
for tape records being too large for the supplied buffer get caught. Do
some other saerrro cleanup.
Per Ken && Justin, add my name to copyright comment.
entity. Add the Device Configuration page data structure- this structure
should be used if you fail to fetch the DATA COMPRESSION page. Make a union
type of a mode header, a device configuration page and the data compression
page.
Add a couple of QIC density defines (QIC 2G/QIC 4GB).
If the client requests that the error recovery code retry a selection
timeout, it will be retried after half a second. The delay is to give the
device time to recover.
For most of these drivers, I only added selection timeout retries where
they were also retrying unit attention type errors. The sa(4) driver calls
saerror() in a number of places, but most of them don't request retrying
unit attentions.
Also, bump the default minimum CD changer timeout from 2 to 5 seconds and
the maximum timeout from 10 to 15 seconds. Some Pioneer changers seem to
have trouble with the shorter timeout.
Reviewed by: gibbs
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
emulator so that instances can be dynamically added and removed from the
system.
Properly reference count peripheral instances so they are cleaned up when
destroyed by the control device.
Set a timeout for test unit ready commands. Before it was uninitialized
and could cause us to drop off the bus when no real timeout had occurred.
catch a T4000s)
+ Set *some* kind of error at EOM if we're in fixed mode and have pending errs.
Do not clear the ERR_PENDING bit if more buffers are queued.
+ Release the start_ccb in this case also, else we hang forever on rewinding.
+ Any kind of error for load to BOT in samount should then cause an attempt
to use REWIND to come back to BOT. Do the initial load command quietly.
+ In samount, if we succeed, set the relative position markers.
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
of the minor). Establish and use a control mode open. Control
mode opens may open the device without locking, but are prohibited
from all but some ioctls. MTIOCGET always works. MTIOCERRSTAT
works, but the clearing of latched error status is contingent
upon whether another application has the device open, in which
case an interruptible perip acquire is done. MTSETBSIZ, MTSETDNSTY
and MTCOMP also require a periph aquire.
Relative fileno and blkno are tracked. Note that just about any
error will make these undefined, and if you space to EOD or use
hardware block positioning, these are also lost until the next
UNLOAD or REWIND.
Driver state is also tracked and recorded in the unit softc
to be passed back in mt_dsreg for a MTIOCGET call.
Thanks to Dan Strick for suggesting this.
Reintroduce 2 filemarks at EOD for all but QIC devices. I
really think it's wrong, but there is a lot of 3rd party
software that depends upon this (not the least of which is
tcopy). Introduce a SA_QUIRK_1FM to ensure that some devices
can be marked as only being able to do 1 FM at EOD.
At samount time force a load to BOT if we aren't mounted. If the
LOAD command fails, use the REWIND command (e.g., for the IBM 3590
which for some gawdawful reason doesn't support the LOAD (to BOT)
command).
Also at samount time, if you don't know fixed or variable, try to
*set* to one of the known fixed (or variable, for special case)
density codes. We only have to do this once per boot, so it's not
that painful. This is another way to try and figure out the wierd
QIC devices without having to quirk everything in the universe.
A substantial amount of cleanup as to what operations can and what
operations cannot be retried. Don't retry space operations if they
fail- it'll just lead to lossage.
Not yet done is invalidating mounts correctly after errors. ENOTIME.
idiot about testing SA_QUIRK_2FM in samount. Fixed.
Removed the NORRLS quirk (to save quirk space) and left
the behaviour of being quiet about failed reserve/release
(failed due Illegal Request) the same.
Added a SF_QUIET_IR for prevent/allow for the same purposes.
(<blank@fox.uni-trier.de>) about quirks being set as
arithmetic values, not as bitfields. Add HP, Kennedy
and M4 1/2" reel quirk entries.
Do a lot of gratuitous source changing.
Audit all functions that build ccbs for the tape driver
and decide whether each one can be retried or not.
Still to do is some more state management post errors.
data and sense information for target mode devices for which no other
peripheral driver is attached. This simplifies the task of dealing with
luns that are not otherwise enabled for target mode if the controller
does not have firmware that automatically deals with this case (e.g.
the aic7xxx driver).
from the old driver. Change format of quirk table to have a preferred block
size for devices that need to be QUIRK_FIXED- this is loaded into the
last_media_blocksize tag at saregister time and will be used in the first
samount case.
Change sasetparams to take a sense_flags argument so that probe time testing
can be quieter (e.g. with SF_NO_PRINT).
Fix a couple of silly bugs in the fixed/variable determination in samount- one
was where there was a check against 'guessing' AND the density code being
default density- *SMACK* - you're only guessing if you find the media code
to be *other* than default density. Second bug was a test against current
blocksize being zero- should be a test against whether current blocksize
is not equal to the last blocksize if you had wanted to be fixed (suppose
you came up in fixed, but not the preferred size?). And if you don't
know what the fixed size should be, select 512 as the starting point,
not BLKDEV_IOSIZE (reality wins). Finally, in doing the test set to variable
mode, make sasetparams non-chatty.
to release the probe ccb before taking down the periph.
Also, don't do cdscheduling if you're not going to
attach the device after all.
Reviewed by: ken@freebsd.org
CAPACITY fail for a non-removable media device. There's a race
condition where the device entry is removed and then
xpt_release_ccb is called which attempts to give back the ccb
to a device that's now gone. In this bandaid release the ccb
early and then remember to not call xpt_release_ccb later.
will) get set for the devices that don't actually support
reserve/release (so we don't keep trying it).
Add softc storage and manage storing last I/O and CTL
commands that had errors (for correlative purposes).
In saclose clear the 'MOUNTED' bit if we either rewind or
unload (yes, this shouldn't be necessary since the next open
should catch whether a tape change occurred, but I'm having
some questions about that actually working so this is
safer for the moment). Oh, forgot to mention in previous
commit messages that some of the failures particularly at
close time cause the tape to be ejected (for the sake
of safety)- all this prior to redoing the state machine
(which is in progress) which will try and handle this better.
Complete the addition of the setmark support
(from Martin.Birgmeier@aon.at).
written even it the tape was opened readonly- 2 botches in deferred error
handling for FIXED LENGTH mode which caused panic && hand resp.). Fixed
a memory leak in sa_mount.
2) Fixed an annoying bug when turning of compression to actually reflect
this for future status calls.
3) Implement the MTIOCERRSTAT call where latched control and I/O residuals
and sense data are returned to the application asking for them.
Attempt to determine (at mount time if not done so already) via density code
whether a device should default to fixed mode or not. Attempts to set to
variable that fail will cause fixed to be selected.
Similarly, the '2 filemarks at EOM' quirk is now determined (or attempted to
be determined) via density code. Some as yet not entirely tested code for
coping with 2FM@EOD position is now also in place.
aborted prior to disabling our lun. This requires a second set of
links since we use the ones in the ccb_hdr during normal operations.
Nuke some unused variables.
level so they can be reclaimed before attempting to disable our lun.
Correctly free descriptors. Add periph locking and spl protection
around open and close.
incorporate some notion of which revision the device is. If it's < SCSI2, for
example, READ BLOCK LIMITS is not a MANDATORY command.
At any rate, the initial state is to try and read block limits to get a notion
of the smallest and largest record size as well as the granularity. However,
this doesn't mean that the device should actually *in* fixed block mode should
the max && min be equal... *That* choice is (for now) determined by whether
the device comes up with a blocksize of nonzero. If so, then it's a fixed block
preferred device, otherwise not (this will change again soon).
When actually doing I/O, and you're in fixed length mode, the block count is
*not* the byte count divided by the minimum block size- it's the byte count
divided by the current blocksize (or use shift/mask shortcuts if that worked
out...).
Then when you *change* the blocksize via an ioctl, make sure this actually
propagates to the stored notion of blocksize (and update the shift/mask
shortcuts).
Misc Other:
When doing a mode select, only use the SCSI_SAME_DENSITY (0x7f) code if
the device is >= SCSI2- otherwise just use the saved density code.
Recover from the ripple of ILLEGAL REQUEST not being 'retried' in that
RESERVE/RELEASE is not a mandatory command for < SCSI2 (so ignore it if it
fails).
Allow sync transfers if the controller supports it. Wide will follow
as soon as I get the kinks worked out of wide target transfers in the
aic7xxx driver (currently the only target mode driver in the tree).
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
not like the 6-byte read and write commands! It returns illegal request,
with the field pointer pointing to byte 9 of a 6 byte CDB.
In any case, the work around is to put in a quirk mechanism that makes sure
that we don't send 6-byte reads or writes to this device. It's rather sad
that this is necessary. You'd think that they would be able to get
something that basic to work right in their firmware...
Reviewed by: gibbs
Reported by: Adam McDougall <bsdx@spawnet.com>
other problem.
- Hold onto splsoftcam() in the peripheral driver open routines until we
have locked the periph. This eliminates a race condition.
- Disallow opening the pass driver when securelevel > 1.
- If a user tries to open the pass driver with O_NONBLOCK set, return
EINVAL instead of ENODEV. (noticed by gibbs)
