Switches that originate their own frames (eg obvious ones like Pause frames)
need a MAC address to use to send those frames from.
This API will hopefully begin to allow that to be configurable.
This stuff may be a bit fluid during this -HEAD cycle as various other
switch features are added, but the current stuff is enough to drive
initial development and features on the atheros range of integrated
and external switches.
* add a method to flush the whole address table;
* add a method to flush all addresses on a given port;
* add a method to download the address table;
* .. and then a method to fetch entries from the address table.
The table fetch/read methods pass through to the drivers for now since
the drivers may implement different ways of fetching/caching the address
table data. The atheros devices for example fetch the table by
iterating over the table through a set of registers and so you need
to keep that locked whilst you iterate otherwise you may have the table
flushed half way by a port status change.
This is a no-op until the userland and arswitch code shows up.
This fix the case when etherswitch is printing the information of port 0
vlan group (in port based vlan mode) with no member ports.
Add the ETHERSWITCH_VID_VALID support to ip17x driver.
Add the ETHERSWITCH_VID_VALID support to rt8366 driver.
arswitch doesn't need to be updated as it doesn't support vlans management
yet.
Approved by: adrian (mentor)
This adds a vlan capability field to etherswitch_info structure and some
definitions of ports flags.
It adds the support to global config parameters which right now is used
only to switch between the vlan modes, but it is intended to be extended
to support the setup of others parameters (STP, mirror, etc.).
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
than VLAN groups.
Some chips (eg this rtl8366rb) has a VLAN group per port - you first
define a set of VLANs in a vlan group, then you assign a VLAN group
to a port.
Other chips (eg the AR8xxx switch chips) have a VLAN ID array per
port - there's no group per se, just a list of vlans that can be
configured.
So for now, the switch API will use the latter and rely on drivers
doing the heavy lifting if one wishes to use the VLAN group method.
Maybe later on both can be supported.
PR: kern/177878
PR: kern/177873
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
This is designed to support the very basic ethernet switch chip behaviour,
specifically:
* accessing switch register space;
* accessing per-PHY registers (for switches that actually expose PHYs);
* basic vlan group support, which applies for the rtl8366 driver but not
for the atheros switches.
This also includes initial support for:
* rtl8366rb support - which is a 10/100/1000 switch which supports
vlan groups;
* Initial Atheros AR8316 switch support - which is a 10/100/1000 switch
which supports an alternate vlan configuration (so the vlan group
methods are stubbed.)
The general idea here is that the switch driver may speak to a variety of
backend busses (mdio, i2c, spi, whatever) and expose:
* If applicable, one or more MDIO busses which ethernet interfaces can
then attach PHYs to via miiproxy/mdioproxy;
* exposes miibusses, one for each port at the moment, so ..
* .. a PHY can be exposed on each miibus, for each switch port, with all
of the existing MII/ifnet framework.
However:
* The ifnet is manually created for now, and it isn't linked into the
interface list, nor can you (currently) send/receive frames on this ifnet.
At some point in the future there may be _some_ support for this, for
switches with a multi-port, isolated mode.
* I'm still in the process of sorting out correct(er) locking.
TODO:
* ray's switch code in zrouter (zrouter.org) includes a much more developed
newbus API that covers the various switch methods, as well as a
capability API so drivers, the switch layer and the userland utility
can properly control the subset of supported features.
The plan is to sort that out later, once the rest of ray's switch drivers
are brought over and extended to export MII busses and PHYs.
Submitted by: Stefan Bethke <stb@lassitu.de>
Reviewed by: ray
