branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
calculations. Keep this changes local to the function so the tick count
is in its natural form otherwise. Previously 1000 was added each time
a tick fired and we divided by 1000 when it was reported. This is done
to reduce rounding errors.
This should fix some problem of SBP2 device probing.
Prior to rev 1.41, we keep writing the register while bus reset phase.
But in rev 1.41, we ignore successive bus reset events and some chips seem to
clear the register after we write to it.
Tested by: Michael Reifenberger <root@nihil.reifenberger.com>
permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
queue items that can be allocated by netgraph and the number of free queue
items that are cached on a private list.
Netgraph places an upper limit on the number of queue items it may allocate.
When there is a large number of netgraph messages travelling through the
system (100k/sec and more) there is a high probability, that messages get
queued at the nodes and netgraph runs out of queue items. In this case the data
flow through netgraph gets blocked. The tuneable for the number of free
items lets one trade memory for performance.
The tunables are also available as read-only sysctls.
PR: kern/47393
Reviewed by: julian
Approved by: jake (mentor)
Always use sys/conf/kern.mk when building kernel/modules.
<bsd.kern.mk> is only preserved for sys/boot/pc98/boot2
for now, but this will be fixed. If there are other
users of <bsd.kern.mk>, please let me know.
Reminded by: bde
Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Move <sys/conf.h> before <sys/disk.h>.
No need for raidread()/raidwrite(), we have generic code for that.
Remove non-functional dump code.
Make raidinit() return the softc, not the dev_t.
Move to "struct disk*" centric API.
Fix printfs' to get name from struct disk instead of dev_t.
OK'ed by: scottl
don't end up freezing the box. This makes VTY locking useless
in the DDB case but a box which is supposed to be physically
secure shouldn't compile DDB anyway.
Reviewed by: silence on -audit
To do this, initialize the d_maj member of the cdevsw to MAJOR_AUTO.
When the cdevsw is first passed to make_dev() a free major number
will be assigned.
Until we have a bit more experience with this a printf will announce
this fact.
Major numbers are not reclaimed, so loading/unloading the same
device driver which uses MAJOR_AUTO will eventually deplete the
pool of free major numbers and the system will panic when it can
not allocate one. Still undecided who to invonvenience with the
solution to this.
Improve SBP device probeing:
- Wait 2 sec before issuing LOGIN ORB expecting the reconnection
hold timer expires.
- Serialize management ORB and scanning LUN by CAM on each target.
This should fix the problem for devices which have multiple LUNs.
Test device is donated by: Jaye Mathisen <mrcpu@internetcds.com>
- Freeze SIM queue for 2 sec after BUS RESET.
- Retry with LOGIN rather than RECONNECT after LOGIN is not completed for
BUS RESET.
- Use appropriate CAM status for BUS RESET and DEVICE RESET.
- Let CAM to scan targets after BUS REST.
- Implement CAM scan target function.
- Keep our own devq freeze count.
- Let CAM to know that SBP does tagged queuing.
These should be merged to RELENG_4 before 4.8-RELEASE.
a correctly aligned address in this block we really want to check, that the
part of the chunk that starts at the aligned address is large enough with
regard to the original request. Comparing it to 0 makes no sense, because this
is always true except in the rare case, that the aligned address is just at
the end of the chunk.
Approved by: jake (mentor)
td_wmesg field in the thread structure points to the description string of
the condition variable or mutex. If the condvar or the mutex had been
initialized from a loadable module that was unloaded in the meantime,
td_wmesg may now point to invalid memory. Retrieving the process table now
may panic the kernel (or access junk). Setting the td_wmesg field to NULL
after unblocking on the condvar/mutex prevents this panic.
PR: kern/47408
Approved by: jake (mentor)
Fixed memory leak in the "nodevice" option implementation.
Use these instead of sed(1) in MD NOTES.
Use a single makefile (sys/conf/makeLINT.mk) to generate
LINT for all architectures. (Previous versions missed
the LINT dependency on Makefile, and i386 version also
missed the dependency on ${NOTES}.)
Fixed bugs in the previous NOTES conversion using the
"nodevice" token and sed(1):
- i386 LINT lost "device pst".
- pc98 LINT lost SC_*, MAXCONS and KBD_DISABLE_KEYMAP_LOAD
options, and got needless DPT_* options.
- Added nooptions PPC_DEBUG, PPC_PROBE_CHIPSET, KBD_INSTALL_CDEV
to sparc64 LINT so that it has a chance to config(8).
This basically returns us to where we were before.
the fxp driver. This is enabled only for the 82550/82551 chips
(PCI revision code 12 or 13). RX and TX checksum offload are
both supported. Transmit offload is limited to TCP and UDP only
right now: there seems to be a problem with IP header checksumming
on transmit in some cases.
This chip has hardware VLAN support as well. I hope to enable
support for this eventually.
- Make transmission of packets work again. This stopped working because
ether_ifattach() was forcing ifp->if_output to be ether_output() and
clobbering our attempt to override this vector with a pointer to
ng_fec_output(). Move the overriding of ifp->if_output to after
ether_ifattach().
- Abandon the use of the netgraph ng_ether_input_p hook for snagging
incoming frames, and instead override the ifp->if_input vector for
interfaces that have been aggregated into our bundle. (I would have
loved to have written things this way in the first place, but I
didn't want to have to be the one to implement the if_input hook
and change all the drivers.) This avoids collisions with the ng_ether
module, which uses the same hook. Each aggregated device now calls
ng_fec_input() directly, which then fakes up the rcvif pointer
before invoking ifp->if_input itself.
This module should actually work now.
that matches snd_max, then do not respond with an ack, just drop the
segment. This fixes a problem where a simultaneous close results in
an ack loop between two time-wait states.
Test case supplied by: Tim Robbins <tjr@FreeBSD.ORG>
Sponsored by: DARPA, NAI Labs
