but it's better than the buggy behavior we have now. If we contigmalloc()
buffers in bus_dmamem_alloc(), then we must configfree() them in
bus_dmamem_free(). Trying to free() them is wrong, and will cause
a panic (at least, it does on the alpha.)
I tripped over this when trying to kldunload my busdma-ified if_rl
driver.
traps, so that ddb can keep control (almost) no matter how it is
entered. This breaks time-critical interrupts while the system is
stopped in ddb, but I haven't noticed any significant problems except
that applications become confused about the time. Lost time will be
adjusted for later. Anyway, the half-baked disabling of interrupts in
Debugger() gives the same problems for the usual way of entering ddb.
bug for bug compatibility to ddb trap handlers after fixing the debugger
trap gates to be interrupt gates, but the fix was never committed. Now
I want the fix to apply to ddb.
- fix segment limit mis-calculation for GCODE_SEL, GDATA_SEL, GPRIV_SEL,
LUCODE_SEL and LUDATA_SEL.
- move `loader(8) metadata' related printf() after cninit().
- use atop macro (address to pages) for segment limit calculation
instead of i386_btop macro (bytes to pages).
- fix style bugs for the declarations of ints.
Reviewed by: bde, msmith (and arch & audit ML)
flags with interrupts disabled to see if we should call ast() during
doreti. This was mostly submitted by Bruce, but his original patch did
the looping in ast() in assembly rather than in the ast() function itself.
Once we've actually called into the ast() function, it's cheaper to just
loop inside the function rather than returning from the function,
performing the check, and then calling the function again. However, we
can optimize the first check to avoid calling the function at all.
Other architectures may choose to implement this optimization if they
wish but it is not required for correct operation.
Submitted by: bde
the process of exiting the kernel. The ast() function now loops as long
as the PS_ASTPENDING or PS_NEEDRESCHED flags are set. It returns with
preemption disabled so that any further AST's that arrive via an
interrupt will be delayed until the low-level MD code returns to user
mode.
- Use u_int's to store the tick counts for profiling purposes so that we
do not need sched_lock just to read p_sticks. This also closes a
problem where the call to addupc_task() could screw up the arithmetic
due to non-atomic reads of p_sticks.
- Axe need_proftick(), aston(), astoff(), astpending(), need_resched(),
clear_resched(), and resched_wanted() in favor of direct bit operations
on p_sflag.
- Fix up locking with sched_lock some. In addupc_intr(), use sched_lock
to ensure pr_addr and pr_ticks are updated atomically with setting
PS_OWEUPC. In ast() we clear pr_ticks atomically with clearing
PS_OWEUPC. We also do not grab the lock just to test a flag.
- Simplify the handling of Giant in ast() slightly.
Reviewed by: bde (mostly)
are a really nasty interface that should have been killed long ago
when 'ptrace(PT_[SG]ETREGS' etc came along. The entity that they
operate on (struct user) will not be around much longer since it
is part-per-process and part-per-thread in a post-KSE world.
gdb does not actually use this except for the obscure 'info udot'
command which does a hexdump of as much of the child's 'struct user'
as it can get. It carries its own #defines so it doesn't break
compiles.
dynamic symbol table buckets and chains. The sparc64 toolchain uses 32
bit .hash entries, unlike other 64 bits architectures (alpha), which use
64 bit entries.
Discussed with: dfr, jdp
were indices in a dense array. The cpuids are a sparse set and treat
them as such, setting up containers only for CPUs activated during
mb_init().
- Fix netstat(1) and systat(1) to treat the per-CPU stats area as a sparse
map, in accordance with the above.
This allows us to properly boot with certain CPUs disactivated. However, if
we later decide to re-activate said CPUs, we will barf until we decide to
implement CPU spinon/spinoff callback hooks to allow for said CPUs' per-CPU
containers to get configured on their activation.
Reported by: mjacob
Partially (sys/ diffs) Submitted by: mjacob
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
right place. Reported by Jonathan Chen <jonc@pinnacle.co.nz> (someone with
the same name who's not me)
PR: i386/8414
Submitted by: Jonathan Chen <jonc@pinnacle.co.nz>
MFC after: 2 weeks
the non-reserved bits of dr7.
During context restore, load dr7 in such a way as to not
disturb reserved bits.
machdep.c: Don't explicitly disallow the setting of the reserved bits
in dr7 since we now keep from setting them when we load dr7
from the PCB.
This allows one to write back the dr7 value obtained from
the system without triggering an EINVAL (one of the
reserved bits always seems to be set after taking a trace
trap).
MFC after: 7 days
we are required to do if we let user processes use the extra 128 bit
registers etc.
This is the base part of the diff I got from:
http://www.issei.org/issei/FreeBSD/sse.html
I believe this is by: Mr. SUZUKI Issei <issei@issei.org>
SMP support apparently by: Takekazu KATO <kato@chino.it.okayama-u.ac.jp>
Test code by: NAKAMURA Kazushi <kaz@kobe1995.net>, see
http://kobe1995.net/~kaz/FreeBSD/SSE.en.html
I have fixed a couple of style(9) deviations. I have some followup
commits to fix a couple of non-style things.
