Originally submitted by: Wayne Self <wself@cdrom.com>
Allow a ppp startup option in rc.conf.
Adjust sysinstall so that it appends to the end of ppp.conf
and uses the generated profile to start ppp in auto mode on
boot.
Submitted by: Josef L. Karthauser <joe@uk.FreeBSD.org>
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
ifconfig, essentially stealing the lease until the user goes and changes
it. The alternative, sadly, is total dysfunction since bpf isn't in
GENERIC and network connectivity would otherwise fail completely on first
bootup when DHCP configuration was attempted again.
The ultimate answer here is to make either bpf a loadable kernel module
(which security conscious admins will be able to simply remove from /modules)
or come up with a lighter weight mechanism just for dhcp and other apps that
need to see broadcast packets but not otherwise sniff the wire in full
bpf glory.
in some code from C. Stone to parse the lease information. This is still
a WIP and this commit is largely intended to allow others to sync up; the
dhclient code still only works when doing dhcp configuration post-install
and requires a bit more work on the boot floppy before it will truly
work in the minimal bootstrapping role.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
a ports tree which was installed initially with the system later,
but this is probably not the general case (user CVSups the repository
rather than the checked-out bits) and it's penalizing everyone else
with excessive inode consumption.
similar to the PNIC I (supported by the pn driver). In fact, it's really
a Macronix 98715A with wake on LAN support added. According to LinkSys,
the PNIC II was jointly developed by Lite-On and Macronis. I get the
feeling Macronix did most of the work. (The datasheet has the Macronix
logo on it, and is in fact nearly identical to the 98715 datasheet, except
for the extra wake on LAN registers.) In any case, the PNIC II works just
fine with the Macronix driver.
The changes are:
- Move PCI ID for the PNIC II from the pn driver to the mx driver.
- Mention PNIC II support in mx.4.
- Mention PNIC II support in RELNOTES.TXT and HARDWARE.TXT.
removal of bio, tty, net
removal of quotes
switches from isa? to nexus? or atkbdc?
additional comments
These bring the kernel config files in sync with those in
RELENG_3
- Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT
and RELNOTES.TXT and the wi.4 man page
- Mention turbo adapters in the wicontrol.8 man page and provide a
complete table of available transmit speed settings
ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
on CDs and FTP sites.
o Collapse some redundant code.
o Fix typo'd menu.
o Restrict searches properly to packages rather than categories.
o Small tweaks to signal handling.
All RELENG_3 candidates.
I simply forgot that I'd already proven this to be a "really good idea that
unfortunately didn't work at all" the *last* time I tried it. Now
I remember. Hmmm. I WILL defeat this evil problem.
RealTek 8029, NetVin 5000, Winbond W89C940, Surecom NE-34, VIA VT86C926.
(checked with Bill Paul)
Mention the Brooktree Bt878 is supported by the Bt848 driver.
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
William Lloyd. New features include:
* many additional command line options
* "fetch" mode
* less bugs :-)
* better README.
Submitted by: William Lloyd <wlloyd@lap.net>
Reviewed by: abial
"passwordtime" is what passwd(1) has actually been using. I suspect
passwordperiod was the original intent. I can't figure-out which,
if either, BSDi uses. If anyone knows...
Enable MS-CHAP support.
release/Makefile:
Build a separate NOCRYPT version of pppd, to keep This Great
Nation's top-secret cryptographic tools out of the filthy hands
of those evil furriners.
feature of packages now so that no version info is embedded.
o Add a default X desktop menu offering afterstep, enlightenment, KDE, GNOME
and Windowmaker desktops instead of the boring twm(1) based one if the
user so chooses. This will require a little testing.
1. Enable use of serial console for installation by using autoboot
instead of boot.
2. Beep when the mfs root floppy needs to be placed in the fdd.
3. Beep again when mfs root image is loaded and the loader waits
for ten seconds before it starts booting for any input. (Serial
console users can say " boot -h" here.)
