and into the bus front ends. For ISA and C-BUS cards, we always need
to grab it. For PC Card, already committed, we need to do some sanity
checking on the data that's in the ROMs before we decide that they are
OK to use. The PC Card code has already been committed and is
independent of this code (which also has to work on NE-1000 cards,
assuming that those cards still work :-).
if_ed_isa.c, and they seem to not be helpful anymore.
o Fix style issues from de-Pification.
o change from _isa_ to _cbus_ to the largest extent possible to reflect that
this is really for cbus, not isa.
o Use ANSI function definitions.
o Use ed_clear_memory
o eliminate kvtop
Make the special hp versions match the general ones. Also use fixed
types in the WD80x3_generic probe, and change callers' arrays to
match. Fix a couple of minor style issues by using newstyle function
definitions in a couple places.
if_ed and rename it to ed_detach(). Tell other busses to use this
routine for detach.
Since I don't actually have any non-pccard ed hardware I can test
with, I've only tested with my pccards.
More improvements in this area likely are possible.
Prodded by: rwatson
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Discussed in from [FreeBSD-tech-jp 3396] to [FreeBSD-tech-jp 3407]
at FreeBSD-tech-jp@jp.freebsd.org.
NOTE: We must put ed_probe_SIC() function into if_ed_isa.c because
this is a bus dependent code. But the ed driver code is not
separated explicitly whether it is bus dependent or independent
now.
Refer to: http://plaza17.mbn.or.jp/~chi/myprog/FreeBSD/sicat.html
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
o Move the ax88190 code to its own function.
o Move all device_method_t, driver_t and DRIVER_MODULE definitions to the
end of files.
o Wrap a few lines > 80 characters.
o Use the same devclass for all ed drivers. This allows machines with
multiple types of cards to have their cards numbered correctly. Before,
you could wind up with two ed0's.
o Protect if_edvar.h from multiple includes because I was there.
