unreasonable time. I've got a PCI mainboard that simply doesn't grok
it, so continuing with a warning (and a keyboard that's working
nevertheless :) seems to be better than spin-looping forever.
add some logging functionality which I find very useful.
'set debug link' will record just link up/down and address assignments.
'set debug connect' will record the entire chat dialog
'set debug carrier' will record just chat lines including 'CARRIER'
(so that I can be sure I'm getting a 28.8 line).
There was a global change required to permit LogPrintf to take a bit
mask instead of a bit position value (to permit logging some events
on either of two flags, so that no change in 'set debug lcp' would
result from the code supporting 'link'. Thus the diffs are rather
long for such a small change. The man page is also touched.
Oh, and there was a slight syntax problem in route.c
Reviewed by: phk
Submitted by: Tony Kimball <alk@Think.COM>
orthogonal with the rest of the system (you can now use either -PPS or
-P PS), and makes the parser more intelligible. The only drawback is
that the old semantics for the -i flag in case a non-numeric argument
is following are no longer fully supported (only if -i is the very
last arg at all), since getopt(3) doesn't support the discticnction
between numeric and non-numeric arguments.
Make lpr also understand dashes as input pseudo filenames. This
finally makes lp(1) fully comply with Posix.2.
a BIOS was not installed, this will still be true by the time we probe
the chip. We use this heuristic to determine if we should use the left
over scratch ram target settings for controllers that don't have an
SEEPROM. We also "snapshot" the host adapter SCSI id and whether ultra
is enabled or not and use these values if a BIOS was installed. The card
will act as if a BIOS was installed even if there wasn't one if you warm
reboot, but since the scratch ram area is still valid in this case, its
hardly worth the effort of writing a shutdown routing that clears out
the scratch ram. This should make users of motherboard controllers
happy.
channel B first as approriate.
Only reset the SCSI bus if the RESET_SCSI bit of SCSICONF is set. This
makes the aic7xxx driver honor all of the configuration settings availible
in SCSI-Select or the ECU.
Fix a benign bug in the reset code that caused us to always wait a full
second after the chip reset. This should shave some time off the probe.
Bug found by pedrosal@nce.ufrj.br (Pedro Salenbauch)
It seems that only the top three sync rates are doubled when in ultra mode,
so update the syncrates table as appropriate.
Found by "Dan Willis" <dan@plutotech.com> and his SCSI bus analyzer
channel B first as approriate.
Even if the BIOS is diabled, the ECU will still set the primary channel
bit, SCSI ID, RESET_SCSI bit, and BOFF_TIME, so use them.
Change #ifdef linux to #ifdef __linux__
aic7xxx_reg.h:
Remove unneeded BOFF_60BCLOCKS
define CHIPRSTACK to be the same as CHIPRST
define RESET_SCSI and CHANNEL_B_PRIMARY bits
All of these aer used during the setup of adapters.
we are consistent in how they are referenced in the handbook, and
so that they are now all clickable URLs. E.g. no more mis-matched
freebsd-hackers@freebsd.org and hackers@freebsd.org. They are used
just like the individual mail addresses defined in authors.sgml.
E.g. &a.doc will expand to:
FreeBSD documentation project mailing list <freebsd-doc@FreeBSD.ORG>
Be consistent in using the FreeBSD.ORG address. All references
to freebsd.org were changed to FreeBSD.ORG.
Use pre-defined addresses for some individuals where available.
The removed files are no longer needed, they are actually labelled as
``Use only if you are not 4.4BSD''. (Yeah, the ol' crufty printcap.c
is really gone!)
Properly declare all external objects in files ending in .h, as
opposed to embed them into files ending in .c.
(PR #1178).
Define a new SO_TIMESTAMP socket option for datagram sockets to return
packet-arrival timestamps as control information (PR #1179).
Submitted by: Louis Mamakos <loiue@TransSys.com>
Subject: Fix for annoying fsck bug
Date: Wed, 24 Jan 1996 13:33:29 -0700 (MST)
The following small diff fixes the annoying fsck bug that causes it to
need to be run twice to end up with correct reference counts for inodes
for directories that had subdirectories relocated into the lost+found
directory.
I found the need to rerun *extremely* annoying. This fix causes the
count to be correctly adjusted later in pass 4 by correctly stating
the parent reference count.
Note that the parent reference count is incremented when the directory
entry is made (for ".."), but is not really there in the case of a
directory that does not make an entry in its parent dir.
This can be tested by waiting for the inode sync after cd'ing from a
shell into a test fs. Then you "mkdir xxx yyy zzz", wait a second,
and hit the machine reset button.
Reviewed by: nate (Tested lots of crashes :)
Submitted by: Terry Lambert <terry@lambert.org>
Make "selection bar" inverse video white-on-blue on color screens to avoid
it getting muddled up with popup dialogs.
Do disk selection in a more friendly fashion (for one thing, allow a
drive to be de-selected again if you change your mind).
Add a few strategic screen-saves to prevent corruption of screen contents
(thanks, Michael Elbel!).
boundary, which means that it doesn't mark the start of the data
section (which is then inaccessible to the programmer ??).
Hopefully fixes recent locore reboot problems.
