signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
2. Add OF_getprop_alloc(), a helper function that will malloc() a sufficient
amount of memory and then retrieve a property value into it.
Approved by: benno
Obtained from: NetBSD (1)
disabled unless verbose flag is set. Also fix some messages in terms
of English.
The critical messages and error messages in probe/attach routine are
unchanged by this commit.
Now you can say;
# sysctl hw.acpi.lid_switch_state=NONE
instead of specifying unsupported _Sx object in the system.
Actually, S4B is going to disappear in ACPICA and we already have
hw.acpi.s4bios to distinguish BIOS hibernation or OS hibernation.
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
off chip that was on one prototype board. However, this appears to be
a design that many chipsets are compatible with its PPEC register set
(eg the Omega 82c094). Through the kindness of the Red Hat developer
David Woodhouse, I now have this datasheet.
I may take the advise of one of the bsd-nomads (whose name
unfortunately escapes me at the moment) and split out all these 16-bit
I/O mapped PCI devices into a separate driver...
that it has one BAR that's mapped to 0x3e0 and is I/O only. It does
not conform to the Yenta spec, like other PCI PCMICA bridges do (eg
the TI 1031, which is mostly a 1131 w/o 32bit card support). It
appears that this chip may also need to not route PCI interrupts
as well.
This chip is used in the NEC Versa 2430CD (and it appears that
sometimes it works, while other times it doesn't) and others in the
2400 series. While the NEC website claims Cardbus support, I can't figure
out how that is possible.
Submitted by: Ben Timby <ben@webexc.com>
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
conf/files) and as a result appears to have been missed in the bulk
KSE update of drivers. This change replaces references to proc
with thread. It has not been compile-tested.
in wdrain during a write. This flag needs to be used in devices whos
strategy routines turn-around and issue another high level I/O, such as
when MD turns around and issues a VOP_WRITE to vnode backing store, in order
to avoid deadlocking the dirty buffer draining code.
Remove a vprintf() warning from MD when the backing vnode is found to be
in-use. The syncer of buf_daemon could be flushing the backing vnode at
the time of an MD operation so the warning is not correct.
MFC after: 1 week
be set to 1 to make FreeBSD and Tru64 coexist peacefully on a dual
boot system and not clobber each other's year in the TOY clock.
(Tru64 uses an offset 52 years higher than one would expect)
Obtained from: NetBSD
MFC After: 1 week
- Now that apm loadable module can inform its existence to other kernel
components (e.g. i386/isa/clock.c:startrtclock()'s TCS hack).
- Exchange priority of SI_SUB_CPU and SI_SUB_KLD for above purpose.
- Add simple arbitration mechanism for APM vs. ACPI. This prevents
the kernel enables both of them.
- Remove obsolete `#ifdef DEV_APM' related code.
- Add abstracted interface for Powermanagement operations. Public apm(4)
functions, such as apm_suspend(), should be replaced new interfaces.
Currently only power_pm_suspend (successor of apm_suspend) is implemented.
Reviewed by: peter, arch@ and audit@
us a lot on older Alphas.
Andrew Gallatin, Thomas V. Crimi, and Peter Jeremy contributed to this
work along with the submitter.
Submitted by: Andrew M. Miklic <miklic@home.com>
- Add a new MIB for battery info expire time in order to make it changeable.
Battery info expire time can be specified by
hw.acpi.battery.info_expire in sec.
- Add own MALLOC type and fix some potential memory leakages.
- Change some frequent printings to verbose printing.
- Stop timeout during acpi_cmbat_get_bst() too. This should reduce
the races with BIF evaluation.
- Remove acpi_cmbat_get_bif() invocation from acpi_cmbat_attach().
This was redundant because this should be called from
acpi_cmbat_timeout() now.
- Give a guaranteed minimum cooling run time to avoid too frequent
cooling system On/Off switching. The minimum cooling run time can be
specified by hw.acpi.thermal.min_runtime in sec.
- Refine message printing (_AC-1 -> NONE).
- Add verbose mode enable/disable capability by hw.acpi.verbose in bool.
Reviewed by: acpi-jp@ folks
in the 21143, instead of giving priority to the receive unit.
This gives a 10-15% performance improvement in the forwarding rate
under heavy load.
Reviewed-by: Bill Paul
while it is on a queue with the queue lock and remove the per-task locks.
- Remove TASK_DESTROY now that it is no longer needed.
- Go back to inlining TASK_INIT now that it is short again.
Inspired by: dfr
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
queue, and a mutex to protect the global list of taskqueues. The only
visible change is that a TASK_DESTROY() macro has been added to mirror
the TASK_INIT() macro to destroy a task before it is free'd.
Submitted by: Andrew Reiter <awr@watson.org>
and packet bundling. Make the microcode settings controllable via sysctl
and loader tunables.
Submitted by: Marko Zec <zec@tel.fer.hr>
(with some munging and dynamic sysctl support by me)
Also extend the workaround for Dynamic Standby mode to later '559 chips,
not just the ICH2 variants.
This is taken verbatim from the Intel's e100-1.6.22 release, with
the addition of their LICENSE file at the top.
Submitted by: Marko Zec <zec@tel.fer.hr>
If we get a completion status of RQCS_QUEUE_FULL, it means
that the internal queues are full. Other QLogic boards set
the QFULL SCSI status. But *nooooooooooo*, not the 2300.
MFC after: 1 day
sio_pccard_detach to use new siodetach. Add an extra arg to sioprobe
to tell driver to probe/not probe the device for IRQs.
This incorporates most of Bruce's review material. I'm at a good
checkpoint, but there will be more to come based on bde's further
reviews.
Reviewed by: bde
This might need additional code for hotswapping use, but first
I need to get my hands on actual hw...
Based on docs kindly provided by Promise Inc which we thank for
the close cooperation with the FreeBSD project!.
avoiding EC read errors on some laptops.
- Stop updating Battery info for all user requests
- Update Battery info by notify events and resume method
- Poll Battery info every one minute
Suggested by: takawata
Move sio from isa/sio.c to dev/sio/sio.c. The next step is to break
out the front end attachments, improve support for these parts on
different busses, and maybe, if we're lucky, merging in pc98 support.
It will also be MI and live in conf/files rather than files.*.
Approved by: bde
Tested with: i386, pc98
tracks as /dev/acdNtY.
This solves the problems with having to deal with howmany and which
devices are open.
For hysterical reasons ONLY, make a link to both the acdNa & acdNc devices.
these chips. There is a new hint, hint.pcm.N.hwvol_config, that can be set
to 1 or 0 to select which pins the buttons are connected to. I'm open to
suggestions on where to document this. Also bump the number of playback
channels up to 4.
MFC after: 3 days
- Count the number of this error.
- When the error is detected for the first time, the psm driver will
throw few data bytes (up to entire packet size) and see if it can
get back to sync.
- If the error still persists, the psm driver disable/enable the mouse
and see if it works.
- If the error still persists and the count goes up to 20,
the psm driver reset and reinitialize the mouse. The counter
is reset to zero.
- It also discards an incomplete data packet when the interval
between two consequtive bytes are longer than pre-defined timeout
(2 seconds). The last byte which arrived late will be regarded as
the first byte of a new packet. This is louie's idea.
You may see the following error logs during the above operations:
"psmintr: delay too long; resetting byte count"
"psmintr: out of sync (%04x != %04x)"
"psmintr: discard a byte (%d)"
"psmintr: re-enable the mouse"
"psmintr: reset the mouse"
MFC after: 1 month
