Commit Graph

289 Commits

Author SHA1 Message Date
Bjoern A. Zeeb
1e7d7466b7 Renamed the FRAMELEN macro to TRUEPHY_FRAMELEN as for powerpc
it seems to be possible to collide with FRAMELEN from machine/frame.h.

Found by:	zec
2008-11-28 23:44:13 +00:00
Pyun YongHyeon
d2cd226334 Use auto-negotiation for manual media type selection. This fixes
establishment of 10/100Mbps link on Atheros AR8121(L1E).
2008-10-25 06:39:17 +00:00
Pyun YongHyeon
b8b068386a Correct PHY description and OUI of VSC8211. Previously VSC8211 was
not recognized by ciphy(4) due to the incorrect OUI.

Reported by:	nork
Tested by:	nork
2008-10-23 01:27:15 +00:00
Pyun YongHyeon
b435227b7d Some 88E1149 PHY's page select is initialized to point to other
bank instead of copper/fiber bank which in turn resulted in
wrong registers were accessed during PHY operation. It is
believed that page 0 should be used for copper PHY so reinitialize
E1000_EADR to select default copper PHY.
This fixes link establishment issue of nfe(4) on Sun Fire X4140.

OpenBSD also has similimar patch but they just reset the E1000_EADR
register to page 0. However some Marvell PHYs((88E3082, 88E1000)
don't have the extended address register and the meaning of the
register is quite different for each PHY model. So selecting copper
PHY is limited to 88E1149 PHY which seems to be the only one that
exhibits link establishment problem. If parent device know the type
of PHY(either copper or fiber) that information should be notified
to PHY driver but there is no good way to pass this information yet.

Reported by:	thompsa
Reviewed by:	thompsa
2008-10-17 05:26:51 +00:00
Stanislav Sedov
ba26d470bd - Add driver for Attansic L2 FastEthernet controller found on
Asus EeePC and some Asus mainboards.

Reviewed by:	yongari, rpaulo, jhb
Tested by:	many
Approved by:	kib (mentor)
MFC after:	1 week
2008-10-03 10:31:31 +00:00
Pyun YongHyeon
10bace3e92 Save extended address register prior to switching to 1000BASE-X
only mode and restore original value of extended address register
instead of overwriting it with page 1. There are still instance
information passing issue(e.g configured media type: fiber or
copper) from driver to PHY layer but this change make the selected
PHY work with 88E1112 PHY.

Reported by:	Krzysztof Jedruczyk < beaker <at> hot dot pl >
Tested by:	Krzysztof Jedruczyk < beaker <at> hot dot pl >
2008-09-30 08:18:38 +00:00
Pyun YongHyeon
fdf7d60d6a Add Vitesse VSC8211 PHY which is found on Planex GU-1000T.
HW donated by:	nork
2008-09-30 07:30:05 +00:00
Pyun YongHyeon
f350b4e7cf Explicitly mark IFM_HDX for half-duplex media. 2008-09-30 07:24:20 +00:00
Pyun YongHyeon
937982244e Report current link state while auto-negotiation is in progress. 2008-09-30 07:22:02 +00:00
Pyun YongHyeon
eb10e72371 Use mii_anegticks instead of hardcoded MII_ANEGTICKS. 2008-09-30 07:20:26 +00:00
Pyun YongHyeon
138b38fffa Announce link loss right after it happens. 2008-09-30 07:19:01 +00:00
Rafal Jaworowski
d99ebc85d9 Recognize 88E1116R phy variation. This part is found on some embedded devices.
Obtained from:	Semihalf
2008-09-04 11:09:40 +00:00
Warner Losh
60e984e137 Move the code that looks for the companion phy to a subroutine to make
sure we get the error handling right in both places.  This also
simplifies the code somewhat.
2008-08-23 15:50:18 +00:00
Warner Losh
373444e7a1 It turns out that my analysis of the error handling here was wrong.
When there's an error, we don't want to free the children, since it
will be stack garbage.  While we did fail to dereference it by setting
devs to 0, we didn't fail to call free.  We never failed to fail, it
was the easiest thing to do.
2008-08-23 15:29:28 +00:00
Warner Losh
195c96b714 Revert bogusly committed file. 2008-08-23 07:46:58 +00:00
Warner Losh
e1bd4ee68b Set devs to 0 in case device_get_children return an error. The right thing
to do here is nothing in that case...
2008-08-23 07:46:20 +00:00
Pyun YongHyeon
f8e0f10069 Restore link state handling which was broken in rev 1.69.
Also report current link state while auto-negotiation is in
progress.
With this change link loss should be reported within a second
and drivers that rely on link state should work.

Reported by:	Pete French < petefrench at ticketswitch dot com >
Tested by:	Pete French < petefrench at ticketswitch dot com >
MFC after:	1 week
2008-08-12 00:57:39 +00:00
Pyun YongHyeon
366dbcbd4a Remove 'cr' at the end of line. 2008-08-12 00:55:03 +00:00
Pyun YongHyeon
104d1d8401 Remove whitespace at the end of line. 2008-08-12 00:52:10 +00:00
Kevin Lo
503765e486 Fix a copy/paste error 2008-08-06 07:52:59 +00:00
Pyun YongHyeon
c06cddfef8 Add RTL8211C(L) support.
Disable advanced link-down power saving in phy reset.

Reported by:	nork
Tested by:	nork
2008-07-02 08:10:18 +00:00
Xin LI
cca7141d76 Add et(4), a port of DragonFly's Agere ET1310 10/100/Gigabit
Ethernet device driver, written by sephe@

Obtained from:	DragonFly
Sponsored by:	iXsystems
MFC after:	2 weeks
2008-06-20 19:30:44 +00:00
Xin LI
4d52a57549 Add et(4), a port of DragonFly's Agere ET1310 10/100/Gigabit
Ethernet device driver, written by sephe@

Obtained from:	DragonFly
Sponsored by:	iXsystems
MFC after:	2 weeks
2008-06-20 19:28:33 +00:00
David Christensen
d75672d1c4 - Added support for BCM5709 and BCM5716.
MFC after:	2 weeks
2008-06-13 01:20:29 +00:00
Marcel Moolenaar
cf99524aed Add support for the Apple Big Mac (BMAC) Ethernet controller,
found on various Apple G3 models.

Submitted by:	Nathan Whitehorn
2008-06-07 22:58:32 +00:00
Benno Rice
694c651803 This is a rewritten driver for the SMSC LAN91C111. It's based in part on the
sn(4) driver and also looking at newer drivers.  The reason for the rewrite is
to support MII and to try and resolve some performance issues found when trying
to use the sn(4) driver on the Gumstix network boards.

For reference, the SMSC LAN91C111 is a non-PCI ethernet part whose lineage
dates back to Ye Olde Days of ISA.  It seems to get some use in the embedded
space these days on parts lacking on-board MACs or on-board PCI controllers,
such as the XScale PXA line of ARM CPUs.

This also includes a driver for the SMSC LAN83C183 10/100 PHY.

Man page to follow.
2008-06-06 05:00:49 +00:00
Pyun YongHyeon
6021a944af Add JMicron JMP202/JMP211 PHY driver. 2008-05-27 01:16:40 +00:00
Pyun YongHyeon
d1307e812e Add Attansic/Atheros F1 PHY driver. 2008-05-19 01:12:10 +00:00
John Baldwin
38cc658ff6 Add support for the BCM5906[M] adapters. These adapters only support
10/100 operation and place the mailbox registers at a different offset.
They also do not have an EEPROM, so the MAC address must be read from
NVRAM instead.

MFC after:	1 month
PR:		kern/118975
Submitted by:	benjsc, Thomas Nyström  thn at saeab dot se
Submitted by:	sephe (original patch for DragonflyBSD)
2008-04-29 19:47:13 +00:00
Rafal Jaworowski
324eb73387 Recognize Cicada CS8244 phy chip (among others, can be found on MPC8572DS
development systems).

Obtained from:	Freescale, Semihalf
2008-04-26 18:07:24 +00:00
Pyun YongHyeon
a76215ece3 Add support for IC Plus IP1001 PHY.
Tested by:	Stuart Fraser < stuart AT stuartfraser DOT net >
2008-04-05 00:52:07 +00:00
John Baldwin
bcc20328f5 Flesh out support for the BCM5722 by recognizing the phy on the 5722 and
the specific ASIC revision.

MFC after:	1 week
Obtained from:	OpenBSD (mii/phy bits)
2008-03-06 21:42:48 +00:00
David Christensen
bf10880210 - Add PHY ID for BCM5709C 1000Base-T controllers.
MFC after:	1 week
2008-03-05 22:58:02 +00:00
Pyun YongHyeon
b455d946f5 Add detection of isolation state.
PR:	kern/76710
2008-03-05 01:15:10 +00:00
Rafal Jaworowski
ff857dc5d6 Recognize the quad-port Cicada (Vitesse) CS8204 10/100/1000TX PHY.
This PHY is found on many embedded development boards: among others MPC8555CDS
evaluation systems use it.

Approved by:	cognet (mentor)
MFp4:		e500
2008-03-03 18:44:33 +00:00
Marius Strobl
82f358ff2a - Fix a typo in a comment.
- Fix whitespace according to style(9).
- Sync the comment describing why we have to wait in nsphy_reset()
  with nsphyter_reset(). It's true that the manual tells to not do a
  reset within 500us of applying power but that's unlikely the cause
  of problems seen here. Generally having to wait 500us after a reset
  however is.
2008-01-27 01:30:02 +00:00
Marius Strobl
4f3b854461 Fix a typo in a comment. 2008-01-27 01:11:57 +00:00
Marius Strobl
d47d37af9b Add a driver for the National Semiconductor DP83815, DP83843 and
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.

PR:		112654
Obtained from:	NetBSD
MFC after:	2 weeks
Thanks to:	mlaier for testing w/ DP83815
2008-01-27 01:10:41 +00:00
Jung-uk Kim
86543395c1 Add a flag for Ethernet@WireSpeed capability and correct chip revisions.
The idea was taken from OpenBSD and cross-referenced with Linux driver.
2008-01-18 22:09:50 +00:00
Pyun YongHyeon
5f36bdfcc2 Reset autonegotation timer if media option is not IFM_AUTO.
Make mii_ticks advance, autonegiation is retried every
mii_anegticks seconds.
2007-11-16 10:39:18 +00:00
Pyun YongHyeon
d612cc5947 IEEE 802.3 Annex 28B.3 explicitly specifies the following relative
priorities of the technologies supported by 802.3 Selector Field
value.

1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T

However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.

PR:	92599
2007-11-16 10:25:36 +00:00
Pyun YongHyeon
fa99a6317c Setting sc->mii_anegticks to MII_ANEGTICKS_GIGE in rgephy_attach()
is redundant. mii_phy_add_media() already takes care of that.

Pointed out by:	marius
2007-10-30 00:37:35 +00:00
Marius Strobl
2a6a6e5ca7 - Remove MIIF_NOISOLATE; there's generally no reason to let gentbi(4)
set this flag and it was more or less just copied and pasted from
  another FreeBSD driver while porting this driver from NetBSD, whose
  gentbi(4) doesn't set MIIF_NOISOLATE either.
- Fix spelling in a comment.

OK'ed by:	yongari
MFC after:	3 months
2007-10-29 21:11:55 +00:00
Pyun YongHyeon
6fd47025e1 Add 88E1116/88E1116R PHY support code that takes the PHY out of
power-down mode.

PR:	kern/114086
MFC after:	3 days
2007-10-29 05:50:22 +00:00
Pyun YongHyeon
0bc6ff67a0 Add a newer RTL8211B(L) PHY. 2007-10-29 02:17:44 +00:00
Pyun YongHyeon
648bfbe6a7 Add support for RealTek RTL8211B(L) PHY. It's based on the patch
made by Michael Eisele and the patch was slightly modified by me.
With this change several NVIDIA ethernet controllers(e.g. MCP61)
works.

RTL8211B(L) is RealTek's new gigabit PHY. The PHY has several
features including crossover correction, polarity correction as
well as supporting triple speed(10/100/1000bps). Data transfer
between MAC and PHY is via RGMII for 1000baseT, MII for
10baseT/100baseTX.
Unfortunately, RealTek used the same model number for RTL8211B(L)
PHY so there is no way to discriminate between RTL8211B(L) and its
predecessors. ATM RTL8211B uses revision number 2 so checking the
revision number seems to be only way to identify it.

Obtained from:	Michael Eisele [1]
Tested by:	clemens fischer < ino-qc AT spotteswoode DOT de DOT eu DOT org >
2007-10-29 02:17:07 +00:00
Pyun YongHyeon
37fd5f0fed o RTL8169S/8110S integrated PHY and RTL8211B are gigabit PHYs so set
mii_anegticks to MII_ANEGTICKS_GIGE and use it. Previously it used
  to MII_ANEGTICKS which may not be enough to wait before retrying
  autonegotiation process at 1000bps.
o Reset autonegotation timer if media option is not IFM_AUTO or we
  got a valid link.
o Announce link loss right after it happends.
o Autonegiation is retried every mii_anegticks seconds.
o Report link state changes right after setting autonegotiation.
2007-10-29 02:06:15 +00:00
Pyun YongHyeon
78679427f6 Add icsphy(4), Integrated Circuit Systems PHY driver, ported from
NetBSD. ATM the only consumer of the PHY is XBox with nfe(4) driver.

Submitted by:	Ed Schouten <ed@fxq.nl>
Tested by:	Ed Schouten <ed@fxq.nl>
2007-06-11 02:04:50 +00:00
Pyun YongHyeon
fcb11bb3f9 Add ICS1889/ICS1892/ICS1893 PHY.
Submitted by:	Ed Schouten <ed@fxq.nl>
2007-06-11 02:02:20 +00:00
David Christensen
599741f908 - Fixed a problem that caused autonegotiation failures.
Submitted by:	tor.egge@cvsup.no.freebsd.org
MFC after:	4 weeks
2007-06-08 02:34:44 +00:00