Add software mixer table for FastTrack Ultra.
Only set volume controls which are valid at startup for standard
USB audio devices, so that settings like treble and bass use
the reset defaults.
MFC after: 1 week
PCM API doesn't support showing all the knobs. Make sure all the USB audio
mixer nodes are freed at detach. Before this patch USB audio would leak
some memory at detach. Print out buffer sizes in number of samples at attach.
Fix setting of volume controls when the number of channels is greater than two.
MFC after: 1 week
if unused in that configuration mixer at NID 15 is muted. Probably CODEC
incorrectly reports its internal connections. Hide that muter from the
driver to avoid muting and make built-in speaker work.
There are several different CODECs sharing this ID and I have not enough
information about them and the bug to implement more universal solution.
Tested by: Big Yuuta <init.py@gmail.com>
MFC after: 2 weeks
with the real value in regular way if sensing is supported. This fixes
minor inconsistency when playback redirection appeared in undefined state
on boot if headphones were not connected.
audio devices. This endpoint gives clues to the USB host about the
actual data rate on asynchronous endpoints and makes the more
expensive USB audio devices usable under FreeBSD.
The Linux USB audio driver was used as reference for the
automagic shift of the received value.
MFC after: 1 week
appear on which interface. This fixes detection of some USB audio adapters.
Also increase the channel limit for FULL speed devices to 4 channels.
Tested by: gavin
MFC after: 1 week
device drivers that used to provide this feature.
This is a subset of 241856 (which was reverted)
Reviewed by: des
Approved by: cperciva (implicit)
MFC after: 1 week
make analog input loopback and dual-stream playback work by enabling
signal mixing by nid 22, as it should be according to info returned by
the CODEC. Otherwise pin nid 28 receives only signal from DAC nid 16.
PR: kern/169124
MFC after: 1 week
at r230551.
Also while there, make sense polling use reported for each node separately
instead of reporting accumulated total status.
Submitted by: Barbara <barbara.freebsd@gmail.com> (1)
MFC after: 3 days
names to shorten them. PulseAudio reported to have problems with names
longer then 63 chars and at least in XMMS long names are inconvinient.
Reported by: hselasky
MFC after: 3 days
another process is in open() or stat() for the device node, then
close() from the owning process does not result in cdevsw close
method call. This fixes the pemanent "Device busy" seen.
Changed the sndstat_lock from mutex to sx. This allows to extend
the region covered by the lock, to include the uiomove() call in
sndstat_read() and bufptr increment. This fixes the "panic:
sbuf_put_byte called with finished or corrupt sbuf" seen.
In collaboration with: kib
MFC after: 1 week
MOD_SHUTDOWN is not an end of existence, and there is a life after it.
In particular, code previously called on MOD_SHUTDOWN grabbed lock and
deallocated unit numbering. That caused infinite wait loop if snd_uaudio
tried to destroy its PCM device after that point.
MFC after: 3 days
Code should just use the devtoname() function to obtain the name of a
character device. Also add const keywords to pieces of code that need it
to build properly.
MFC after: 2 weeks
The cs driver requires a table with firmware values. An
alternative firmware is available in a similar Open Sound
System driver. This is actually a partial revert of
Revision 77504.
Special thanks to joel@ for patiently testing several
replacement attempts.
The csa driver and the complete sound system are now free
of the GPL.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
hardware imposes strict limitations on hard buffer and block sizes.
Previous code set soft buffer to be no smaller then hard buffer. On some
cards with fixed 64K physical buffer that caused up to 800ms play latency.
New code allows to set soft buffer size down to just two blocks of the hard
buffer and to not write more then that size ahead to the hardware buffer.
As result of that change I was able to reduce full practically measured
record-playback loop delay in those conditions down to only about 115ms
with theoretical playback latency of only about 50ms.
New code works fine for both vchans and direct cases. In both cases sound(4)
tries to follow hw.snd.latency_profile and hw.snd.latency values and
application-requested buffer and block sizes as much as limitation of two
hardware blocks allows.
Reviewed by: silence on multimedia@
Remove unneeded temporary variable (data) to better match the OSS code.
Remove some unused constants and type definitions.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
- add "+HP" in case of headphones redirection;
- add device type for analog devices, if all pins have the same.
As result now it may look like "Analog 5.1+HP/2.0" or "Front Analog Mic".
I hope it will be more useful than long and confusing.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
