Add initialization to the if_ie driver for the Micom Interlan NI5210 card.
This is a very old 82586 based card with only 8Kb or 16Kb on board memory.
Also only 8-bit wide instead of 16-bit like the AT& or 3COM card.
Warning: this thing is only tested so far that it detects all bits
correctly but is not yet on an ethernet. Will do that tomorrow.
Submitted by:
Update the if_ep driver for the 3C579 and bring over some of the
changes from the netbsd driver.
This is not complete: the detection of the irq in the eisa does not
work and sometimes the reset for the 3C509 in ISA in an EISA bus system
don't work ( Need a hard reset to be found again == reset knob).
DIOCGDINFO, DIOCGPART, DIOCWDINFO, DIOCSDINFO, CDIOCPLAYMSF, CDIOCRESET,
CDIOCEJECT.
CDIOCPLAYBLOCKS removed (old implementation completely wrong and I don't
know how to implement it correctly).
All routines now detects media change correctly.
DELAY_GETREPLAY increased for long time access from first track
to last.
mcd_waitrdy() now use MIN_DELAY=15 as minimal delay which independs
of machine speed.
mcd_doread() now uses real status (old code uses obsoleted soft copy of it).
clear XBSY on error in mcd_doread()
mcd_statrt(): add missing splx(s), cause dead hang with unmatched slpbio()
optimize mcd_doread(), don't set CD mode each time, keep soft copy of mode.
call getdisklabel() _after_ mcdsize() for proper sizes
mcdopen(): old code forget to set MCDREADRAW in flags when open RAW
partition, doread check it for setting RAW CD mode.
Do nothing on stray interrupt (which sometimes occurse, because driver
read data block too slow, DOS driver use 'insb' here). Old stray code
cause timeouts.
Read toc entries code rewritten to return many requested entries
(as supposed) instead of one entry with incorrect structure.
CMDREAD2 requests covered with disable_intr()/enable_intr()
(from DOS driver)
Read junk code added after read block code in doread (from DOS driver)
mcd_read_toc() code fixed to read all needed entries, old code cause
some audio tracks is not played.
mcd_playtracks() code fixed to proper check valid track range.
New binary read modes implemented (from DOS driver).
Submitted by:
Put the printf("can't map 3c507 ram.. into an ifdef DEBUG. This will
confuse only normal users and the ie0 found/not found is sufficient.
Submitted by:
1) if_ie.c:
Changed a printf and put a space in it. Formerly the "<3C507>"
confused the syslog. He tried to see that as the priority to
log that message.
2) isa_device.h:
Changed the iobase variable from short to u_short. EISA
Adresses can go up to 0xf000 and the sign extension doesn't
look good in the probe output. Example:
ep1 at 0xffff8000-0xffff8000f is not good :-), i like more a
ep1 at 0x8000-0x8000f.
3) isa.c:
Changed a string constant from "probe" to "prob", it gets
later already an "ed" tagged on the end.
in your kernel config now).
2) Added ps ddb function from 1.1.5. Cleaned it up a bit and moved into its
own file.
3) Added \r handing in db_printf.
4) Added missing memory usage stats to statclock().
5) Added dummy function to pseudo_set so it will be emitted if there
are no other pseudo declarations.
2) DELAY(1) does nothing, it affects audio playing f.e:
driver can't play second half of disk, changed to DELAY(10)
3) Debugging messages #ifdef DEBUGed
find something useful to do other than taking credit for other people's
work. Also make the 3C507 bits match the indentation style of the rest of
the code.
Merged changes from 2.0 version (revisions 1.46-1.50) by hand.
Finished conversion to clists: removed flush of tty output buffer
in comflush() (most writes were truncated to 256 bytes) and restored
bypass of ttyinput() in siopoll().
Finished conversion to 2.0 types - more void *'s, less caddr_t's,
less casts, no Dev_t's.
Only these things are seriously broken now compared with 1.1.5:
waiting for output complete is impossible so ttywait() can deadlock;
sioclose() isn't called enough so sioopen() sometimes returns EBUSY
unnecessarily; input flow control is not implemented.
Submitted by:
Add the 3com 3C507 card to the if_ie.c driver. The files elink.c and
elink.h are helding routines that are shared between the 3C507 and the
3C509/3C579. if_ie507.h are constant declarations unique to the 3C507.
The code is based on the NetBSD driver if_ie.c donated to NetBSD by
Rafal Boni and then modified by Charles Hannum.
Added a missing #ifdef INET wrapper in lpt.c
Main change:
Removed the timeout_func_t casts from timeout calls and
correctly defined the timeout routines to conform to
the new format.
lpt.c doesn't have this change.
Reviewed by:
Submitted by:
use of timeout_t -> timeout_func_t in aha1542 and aha1742 drivers.
2) fix a bug in the portalfs that was uncovered by better prototyping -
specifically, the time must be converted from timeval to timespec
before storing in va_atime.
3) fixed/added some miscellaneous prototypes
- Delete redundant declarations.
- Add -Wredundant-declarations to Makefile.i386 so they don't come back.
- Delete sloppy COMMON-style declarations of uninitialized data in
header files.
- Add a few prototypes.
- Clean up warnings resulting from the above.
NB: ioconf.c will still generate a redundant-declaration warning, which
is unavoidable unless somebody volunteers to make `config' smarter.
/usr/src/sys/i386/isa/clock.c:
o Garrett's statclock changes.
o Wire xxxintr, not Vclk.
o Wire using register_intr(), not setidt().
/usr/src/sys/i386/isa/icu.s:
o Garrett's statclock changes.
o Removed unused variable high_imask.
o Fake int 8 for rtc as well as int 0 for clk. Required for kernel
profiling with statclock, harmless otherwise.
/usr/src/sys/i386/isa/isa.c:
o Allow isdp->id_irq and other things in *isdp to be changed by
probes. Changing interrupts later requires direct calls to
register_intr() and unregister_intr() and more care.
ALLOW_CONFLICT_* is brought over from 1.1.5, except
ALLOW_CONFLICT_IRQ is not supported. IRQ conflict checking is
delayed until after probing so that drivers can change the IRQ
to a free one; real conflicts require more cooperation between
drivers to handle.
o Too many details to list.
o This file requires splitting and a lot more work.
/usr/src/sys/i386/isa/isa_device.h:
o Declare more things more completely.
/usr/src/sys/i386/isa/sio.c:
o Prepare to register interrupt handlers as fast.
/usr/src/sys/i386/isa/vector.s:
o Generate entry code for 16 fast interrupt handlers and 16 normal
interrupt handlers. Changed some constants to variables:
# $unit is now intr_unit[intr]. Type is int. Someday it should
be a cookie suitable for the handler (e.g., a struct com_s for
sio).
# $handler is now intr_handler[intr].
# intrcnt_actv[id_num] is now *intr_countp[intr]. The indirection
is required to get a contiguous range of counters for vmstat
and so that the drivers depend more in the driver than on the
interrupt number (drivers could take turns using an interrupt
and the counts would remain correct). There is a separate
counter for each device and for each stray interrupt. In
1.1.5, stray interrupt 7 clobbers the count for device 7 or
something worse if there is no device 7 :-(.
# mask is now intr_mask[intr] (was already indirect).
o Entry points are now _XintrI and _XfastintrI (I = intr = 0-15),
not _VdevU (U = unit).
o Removed BUILD_VECTORS stuff. There's a trace of it left for
the string table for vmstat but config now generates the
string in one piece because nothing more is required.
o Removed old handling of stray interrupts and older comments
about it.
Submitted by: Bruce Evans
``changes'' are actually not changes at all, but CVS sometimes has trouble
telling the difference.
This also includes support for second-directory compiles. This is not
quite complete yet, as `config' doesn't yet do the right thing. You can
still make it work trivially, however, by doing the following:
rm /sys/compile
mkdir /usr/obj/sys/compile
ln -s M-. /sys/compile
cd /sys/i386/conf
config MYKERNEL
cd ../../compile/MYKERNEL
ln -s /sys @
rm machine
ln -s @/i386/include machine
make depend
make
change all of these to be timeout_funt_t and remove the casts and
typedef?
Remove secound argument (uban) from ifp->if_reset routines since it is now
obsolete.
Reviewed by: David Greenman
1) check va before clearing the page clean flag. Not doing so was
causing the vnode pager error 5 messages when paging from
NFS. (pmap.c)
2) put back interrupt protection in idle_loop. Bruce didn't think
it was necessary, John insists that it is (and I agree). (swtch.s)
3) various improvements to the clustering code (vm_machdep.c). It's
now enabled/used by default.
4) bad disk blocks are now handled properly when doing clustered IOs.
(wd.c, vm_machdep.c)
5) bogus bad block handling fixed in wd.c.
6) algorithm improvements to the pageout/pagescan daemons. It's amazing
how well 4MB machines work now.
finally have the f**king documentation!):
1) Changed all the numeric register offsets to symbolic ones (it should
have been this way originally).
2) If 16 bit, disable the shared memory when not using it. Apparantly
switching between 8/16bit mode makes the Ultra unhappy unless
this is done (i.e. it trashes the bus).
