Tested on Qemu/KVM, VirtualBox, and BHyVe.
Currently built as modules-only on i386/amd64. Man pages not yet hooked
up, pending review.
Submitted by: Bryan Venteicher bryanv at daemoninthecloset dot org
Reviewed by: bz
MFC after: 4 weeks or so
I/O from userspace, capable of line rate at 10G, see
http://info.iet.unipi.it/~luigi/netmap/
At this time I am bringing in only the generic code (sys/dev/netmap/
plus two headers under sys/net/), and some sample applications in
tools/tools/netmap. There is also a manpage in share/man/man4 [1]
In order to make use of the framework you need to build a kernel
with "device netmap", and patch individual drivers with the code
that you can find in
sys/dev/netmap/head.diff
The file will go away as the relevant pieces are committed to
the various device drivers, which should happen in a few days
after talking to the driver maintainers.
Netmap support is available at the moment for Intel 10G and 1G
cards (ixgbe, em/lem/igb), and for the Realtek 1G card ("re").
I have partial patches for "bge" and am starting to work on "cxgbe".
Hopefully changes are trivial enough so interested third parties
can submit their patches. Interested people can contact me
for advice on how to add netmap support to specific devices.
CREDITS:
Netmap has been developed by Luigi Rizzo and other collaborators
at the Universita` di Pisa, and supported by EU project CHANGE
(http://www.change-project.eu/)
The code is distributed under a BSD Copyright.
[1] In my opinion is a bad idea to have all manpage in one directory.
We should place kernel documentation in the same dir that contains
the code, which would make it much simpler to keep doc and code
in sync, reduce the clutter in share/man/ and incidentally is
the policy used for all of userspace code.
Makefiles and doc tools can be trivially adjusted to find the
manpages in the relevant subdirs.
This enables locking consumers to pass their own structures around as const and
be able to assert locks embedded into those structures.
Reviewed by: ed, kib, jhb
based on Solarflare SFC9000 family controllers. The driver supports jumbo
frames, transmit/receive checksum offload, TCP Segmentation Offload (TSO),
Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side
Scaling (RSS) using MSI-X interrupts.
This work was sponsored by Solarflare Communications, Inc.
My sincere thanks to Ben Hutchings for doing a lot of the hard work!
Sponsored by: Solarflare Communications, Inc.
MFC after: 3 weeks
curthread-accessing part of mtx_{,un}lock(9) when using a r210623-style
curthread implementation on sparc64, crashing the kernel in its early
cycles as PCPU isn't set up, yet (and can't be set up as OFW is one of the
things we need for that, which leads to a chicken-and-egg problem). What
happens is that due to the fact that the idea of r210623 actually is to
allow the compiler to cache invocations of curthread, it factors out
obtaining curthread needed for both mtx_lock(9) and mtx_unlock(9) to
before the branch based on kobj_mutex_inited when compiling the kernel
without the debugging options. So change kobj_class_compile_static(9)
to just never acquire kobj_mtx, effectively restricting it to its
documented use, and add a kobj_init_static(9) for initializing objects
using a class compiled with the former and that also avoids using mutex(9)
(and malloc(9)). Also assert in both of these functions that they are
used in their intended way only.
While at it, inline kobj_register_method() and kobj_unregister_method()
as there wasn't much point for factoring them out in the first place
and so that a reader of the code has to figure out the locking for
fewer functions missing a KOBJ_ASSERT.
Tested on powerpc{,64} by andreast.
Reviewed by: nwhitehorn (earlier version), jhb
MFC after: 3 days
document knlist_delete, and better document what knlist_clear does... Note
that both of these functions may sleep, and also unlock/relock the list
lock...
document knlist_init_mtx (forgotten by kib)...
other minor improvements
Reviewed by: ru (previous rev)
MFC after: 1 week
Newsletter VI-9 2011-06-12
Name changes for Fiji and Myanmar as well as other minor corrections
Newsletter VI-10 2011-08-09
Code elements for South Sudan.
Reviewed by: http://www.iso.org/iso/country_codes.html
libtool.m4. With these fixes libtool will correctly indentify the
system as ELF (and not a.out).
- While here, change the substitutions so they're still correctly
match freebsd1.x, freebsd2.x etc.
With this, I can build various ports on a 10.0-CURRENT system without
hacking or hiding the version number.
This commit should be reverted when there is a cleaner fix in autotools
and/or ports/Mk/bsd.port.mk.
The original patch is from Ed Schouten but needed some additions.
thanks for their contiued support to FreeBSD.
This is version 10.80.00.003 from codeset 10.2.1 [1]
Obtained from: LSI http://kb.lsi.com/Download16574.aspx [1]
CAM.
Desriptor sense is a new sense data format that originated in SPC-3. Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.
This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.
This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.
camcontrol.c: Change uses of scsi_extract_sense() to use
scsi_extract_sense_len().
Use scsi_get_sks() instead of accessing sense key specific
data directly.
scsi_modes: Update the control mode page to the latest version (SPC-4).
scsi_cmds.c,
scsi_target.c: Change references to struct scsi_sense_data to struct
scsi_sense_data_fixed. This should be changed to allow the
user to specify fixed or descriptor sense, and then use
scsi_set_sense_data() to build the sense data.
ps3cdrom.c: Use scsi_set_sense_data() instead of setting sense data
manually.
cam_periph.c: Use scsi_extract_sense_len() instead of using
scsi_extract_sense() or accessing sense data directly.
cam_ccb.h: Bump the CAM_VERSION from 0x15 to 0x16. The change of
struct scsi_sense_data from 32 to 252 bytes changes the
size of struct ccb_scsiio, but not the size of union ccb.
So the version must be bumped to prevent structure
mis-matches.
scsi_all.h: Lots of updated SCSI sense data and other structures.
Add function prototypes for the new sense data functions.
Take out the inline implementation of scsi_extract_sense().
It is now too large to put in a header file.
Add macros to calculate whether fields are present and
filled in fixed and descriptor sense data
scsi_all.c: In scsi_op_desc(), allow the user to pass in NULL inquiry
data, and we'll assume a direct access device in that case.
Changed the SCSI RESERVED sense key name and description
to COMPLETED, as it is now defined in the spec.
Change the error recovery action for a number of read errors
to prevent lots of retries when the drive has said that the
block isn't accessible. This speeds up reconstruction of
the block by any RAID software running on top of the drive
(e.g. ZFS).
In scsi_sense_desc(), allow for invalid sense key numbers.
This allows calling this routine without checking the input
values first.
Change scsi_error_action() to use scsi_extract_sense_len(),
and handle things when invalid asc/ascq values are
encountered.
Add a new routine, scsi_desc_iterate(), that will call the
supplied function for every descriptor in descriptor format
sense data.
Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
which build descriptor and fixed format sense data. They
currently default to fixed format sense data.
Add a number of scsi_get_*() functions, which get different
types of sense data fields from either fixed or descriptor
format sense data, if the data is present.
Add a number of scsi_*_sbuf() functions, which print
formatted versions of various sense data fields. These
functions work for either fixed or descriptor sense.
Add a number of scsi_sense_*_sbuf() functions, which have a
standard calling interface and print the indicated field.
These functions take descriptors only.
Add scsi_sense_desc_sbuf(), which will print a formatted
version of the given sense descriptor.
Pull out a majority of the scsi_sense_sbuf() function and
put it into scsi_sense_only_sbuf(). This allows callers
that don't use struct ccb_scsiio to easily utilize the
printing routines. Revamp that function to handle
descriptor sense and use the new sense fetching and
printing routines.
Move scsi_extract_sense() into scsi_all.c, and implement it
in terms of the new function, scsi_extract_sense_len().
The _len() version takes a length (which should be the
sense length - residual) and can indicate which fields are
present and valid in the sense data.
Add a couple of new scsi_get_*() routines to get the sense
key, asc, and ascq only.
mly.c: Rename struct scsi_sense_data to struct
scsi_sense_data_fixed.
sbp_targ.c: Use the new sense fetching routines to get sense data
instead of accessing it directly.
sbp.c: Change the firewire/SCSI sense data transformation code to
use struct scsi_sense_data_fixed instead of struct
scsi_sense_data. This should be changed later to use
scsi_set_sense_data().
ciss.c: Calculate the sense residual properly. Use
scsi_get_sense_key() to fetch the sense key.
mps_sas.c,
mpt_cam.c: Set the sense residual properly.
iir.c: Use scsi_set_sense_data() instead of building sense data by
hand.
iscsi_subr.c: Use scsi_extract_sense_len() instead of grabbing sense data
directly.
umass.c: Use scsi_set_sense_data() to build sense data.
Grab the sense key using scsi_get_sense_key().
Calculate the sense residual properly.
isp_freebsd.h: Use scsi_get_*() routines to grab asc, ascq, and sense key
values.
Calculate and set the sense residual.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
too-thorough cleanup of unused files, in r213695. Also make sure these
get installed under /usr/share/doc.
Submitted by: rwatson, brooks
Pointy hat to: dim
MFC after: 3 days
- Emphasize $ipv6_enable and $ipv6_prefer are deprecated.
- Add more detail descriptions about $ipv6_activate_all_interfaces.
- Add some more examples of $ifconfig_IF_ipv6.
- rtsold(8) and rtadvd(8) can be used even when ipv6_gateway_enable=NO now.
Approved by: re (kib)
mod_cc.4 and mod_cc.9 respectively to avoid any possible confusion with the cc.1
gcc man page. Update references to these man pages where required.
Requested by: Grenville Armitage
Approved by: re (kib)
MFC after: 3 days
If it overflows before the taskqueue can run, the task will be
re-added to the taskqueue and cause a loop in the task list.
Reported by: Arnaud Lacombe <lacombar@gmail.com>
Submitted by: Ryan Stone <rysto32@gmail.com>
Reviewed by: jhb
Approved by: re (kib)
MFC after: 1 day
- We no longer use the same data structure in as NetBSD in pucdata.c.
- ppc(4) has had a puc(4) attachment for a while now.
Approved by: re (blackend)
MFC after: 3 days
If a selinfo object is recorded (via selrecord()) and then it is
quickly destroyed, with the waiters missing the opportunity to awake,
at the next iteration they will find the selinfo object destroyed,
causing a PF#.
That happens because the selinfo interface has no way to drain the
waiters before to destroy the registered selinfo object. Also this
race is quite rare to get in practice, because it would require a
selrecord(), a poll request by another thread and a quick destruction
of the selrecord()'ed selinfo object.
Fix this by adding the seldrain() routine which should be called
before to destroy the selinfo objects (in order to avoid such case),
and fix the present cases where it might have already been called.
Sometimes, the context is safe enough to prevent this type of race,
like it happens in device drivers which installs selinfo objects on
poll callbacks. There, the destruction of the selinfo object happens
at driver detach time, when all the filedescriptors should be already
closed, thus there cannot be a race.
For this case, mfi(4) device driver can be set as an example, as it
implements a full correct logic for preventing this from happening.
Sponsored by: Sandvine Incorporated
Reported by: rstone
Tested by: pluknet
Reviewed by: jhb, kib
Approved by: re (bz)
MFC after: 3 weeks
Update to use the latest version of the PCI IDs Repository.
As discussed on -current@ in May, this brings in a new source of the database,
which is also used by other operating systems. Our previous sources no longer
exist and this database is actively maintained and more complete in general.
This includes a structural change regarding atomic ops. Previously they
were enabled on all platforms unless we had knowledge that they did not
work. However both work performed by marius@ on sparc64 and the fact that
the 9.8.x branch is fussier in this area has demonstrated that this is
not a safe approach. So I've modified a patch provided by marius to
enable them for i386, amd64, and ia64 only.
As Garrett points out,
It is no more a debugging interface than setproctitle(3), and has not
been since the name started getting stuffed into the kernel. This
statement may have made sense when the name was only visible in thread
state dumps and the debugger.
PR: threads/158815
Submitted by: wollman@
driver.
Mention all ASIX USB controllers that are supported by axe(4).
Reword media types and explicly mention AX88178 is the only
controller that supports gigabit link.
While I'm here use shorten model instead of showing all controller
model numbers.
to be assigned to a non-default FIB instance.
You may need to recompile world or ports due to the change of struct ifnet.
Submitted by: cjsp
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
(original versions)
Reviewed by: julian
Reviewed by: Alexander V. Chernikov (melifaro ipfw.ru)
MFC after: 2 weeks
X-MFC: use spare in struct ifnet
This knob removes the tools that are exclusively used to view and
maintain the databases maintained by utmpx, namely last, users, who,
wtmpcvt, ac, lastlogin and utxrm.
The tool w is not in this list, because it has some other functionality
which is unrelated to utmpx; it is hardlinked to the uptime tool.
doc/, and now www/ trees, but only using the "cvsup" transport.
When "make update" is run using a tree's makefile, it can also use
"cvs" (except for www/) and "svn" (only src/).
Clean up documentation and code regarding "make update":
- Increase oddness by adding support for WWWSUPFILE and NO_WWWUPDATE to
Makefile.inc1 (analogous to PORTSSUPFILE/NO_PORTSUPDATE and
DOCSUPFILE/NO_DOCUPDATE; WWWSUPFILE already supported by www/Makefile).
- Document all trees that support CVS_UPDATE.
- Document all trees that support SUP_UPDATE.
- Document SVN_UPDATE.
- Document NO_WWWUPDATE.
- make.conf(5) mistakenly said that *SUPFILE* had defaults.
- Add an example entry for WWWSUPFILE.
POSIX says an empty entry in CDPATH shall not result in the new directory
being printed, while any non-empty entry shall result in the new directory
being printed, including ".". Therefore, the value of CDPATH should almost
always start with a colon, not dot and colon.
Our sh does not print the name for empty entries as well as "." entries.
MFC after: 1 week
the system to proceed to boot without bailing out into single user mode,
even when the file system can not be successfully mounted.
This option is implemented in mount(8) and not passed into kernel.
MFC after: 1 month
Many thanks to Tino <tinotom@gmail.com> for drawing my attention to
this, for doing a lot of testing and providing great feedback.
Many thanks to AMD for continuing to release public specifications for
their chipsets.
PR: kern/157568
Tested by: Tino <tinotom@gmail.com>
MFC after: 1 week
uses the .RP macro, a separate cover page is created as page 0 which
is not otherwise output. The bug was hiding by a hack in troffrc
that disables SGR support in grotty(1), which I'm going to remove now.
For POLA reasons, still disable SGR support in grotty(1), by passing
-P-c to groff(1). If we want SGR sequences in these documents, this
can be removed.
MFC after: 1 week
controllers because of TX MAC hangs when trying to send a frame
that is larger than 4K (see r200759).
PR: docs/156742
Submitted by: Michael Moll (kvedulv at kvedulv dot de)
Reviewed by: yongari@
MFC after: 6 days
being able to verify, but also having the ability to
fetch distfiles that are missing or failed the checksum
calculation
PR: docs/138887
Submitted by: Radim Kolar (hsn at sendmail dot cz)
MFC after: 5 days
WITH{OUT,}_KERNEL_SYMBOLS (defaulting to WITH). In the fullness of
time, likely around 2020, INSTALL_NODEBUG will be removed. For now,
don't print a warning when using INSTALL_NODEBUG, but that will be
coming soon.
which is now disabled by default. The detection is known to cause hangs
on boot with some new Lenovo laptops on FreeBSD/amd64.
Reported by: gnn
Discussed with: jkim
MFC after: 3 months
When supported by hardware, this allows to control per-port activity, locate
and fault LEDs via the led(4) API for localization and status reporting
purposes. Supporting AHCI controllers may transmit that information to the
backplane controllers via SGPIO interface. Backplane controllers interpret
received statuses in some way (IBPI standard) to report them using present
indicators.
I checked with http://www.iso.org/iso/country_codes/iso_3166_code_lists.htm
and "MF" was officially spelled in English as "Saint Martin" there, but now
that "SX" exists (for "Sint Maarten (Dutch part)") (nice official "English"
spelling!) they seem to have added a "(French part)" suffix to "MF". Since
this is also in line with Newsletter VI-1 (2007-09-21), catch up.
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
